Advertisement
Mini-Dome Camera Installation Manual
Content
Introduction
The MobileView™ Mini-Dome Camera Installation
Manual includes instructions for installation inside a
transit vehicle. Read through these instructions before
installation.
To use this document, you must have the following
minimum qualifications:
A basic knowledge of CCTV systems and
components; and
A basic knowledge of electrical wiring and low-
voltage electrical hookups.
Location and Preparation
The mini-dome camera is designed for interior use only.
Choose a protected location inside the vehicle that will
deliver the desired image.
Before beginning, confirm you have the following parts
required for installation:
MobileView™ Mini-Dome Camera
Three (3) machine screws with red nylon washers
Three (3) flat-head sheet-metal screws with black
nylon washers (optional)
Hex wrench
Mini-Dome Camera Installation Manual
MobileView™ Part Numbers:
MVC-7100-29-BL
Mini-dome, 600TVL, 2.9mm lens, black, No IR
MVC-7100-29-BLI Mini-dome, 600 TVL, 2.9mm lens, black, with IR
MVC-7100-29-W
Mini-dome, 600TVL, 2.9mm lens, white, No IR
MVC-7100-29-WI
Mini-dome, 600TVL, 2.9mm lens, white, with IR
MVC-7100-36-BL
Mini-dome, 600 TVL, 3.6mm lens, black, No IR
MVC-7100-36-BLI Mini-dome, 600 TVL, 3.6mm lens, black, with IR
MVC-7100-36-W
Mini-dome, 600TVL, 3.6mm lens, white, No IR
MVC-7100-36-WI
Mini-dome, 600TVL, 3.6mm lens, white, with IR
MVC-7100-60-BL
Mini-dome, 600TVL, 6.0mm lens, black, No IR
MVC-7100-60-BLI Mini-dome, 600 TVL, 6.0mm lens, black, with IR
MVC-7100-60-W
Mini-dome, 600TVL, 6.0mm lens, white, No IR
MVC-7100-60-WI
Mini-dome, 600TVL, 6.0mm lens, white, with IR
MVC-7200-29-BL
Mini-dome, 520 TVL, 2.9mm lens, black, with WDR
MVC-7200-29-W
Mini-dome, 520 TVL, 2.9mm lens, white, with WDR
MVC-7200-36-BL
Mini-dome, 520 TVL, 3.6mm lens, black, with WDR
MVC-7200-36-W
Mini-dome, 520 TVL, 3.6mm lens, white, with WDR
MVC-7200-60-BL
Mini-dome, 520 TVL, 6.0mm lens, black, with WDR
MVC-7200-60-W
Mini-dome, 520 TVL, 6.0mm lens, white, with WDR
Installation
Mounting the Camera
1. Using the provided hex wrench, loosen the set
screw on the side of the camera just enough to
unscrew the lens cover. See Figure 1.
Figure 1 Loosen set screw
1
Advertisement
Table of Contents
Related Manuals for Interlogix MobileView MVC-7100-29-BL
Summary of Contents for Interlogix MobileView MVC-7100-29-BL
- Page 1 Mini-Dome Camera Installation Manual Content MobileView™ Part Numbers: MVC-7100-29-BL Mini-dome, 600TVL, 2.9mm lens, black, No IR Introduction 1 MVC-7100-29-BLI Mini-dome, 600 TVL, 2.9mm lens, black, with IR Location and Preparation 1 MVC-7100-29-W Mini-dome, 600TVL, 2.9mm lens, white, No IR Installation 1 MVC-7100-29-WI Mini-dome, 600TVL, 2.9mm lens, white, with IR...
- Page 2 2. Using the camera mounting base as a guide, mark 6. If using rivnuts, install stainless steel rivnuts as the center of the mounting base and the position of shown in Figure 5. the three mounting screws on the mounting surface as shown in Figure 2.
- Page 3 Figure 7 Remove the cover Installing the cover 1. Install the camera cover by tightening in a clockwise direction. Figure 9 Replace the cover and tighten the set screw Adjusting the lens Once the camera is mounted, it is adjustable in three dimensions.
-
Page 4: Contact Information
Ensure that the BNC connector inside the connection box is wrapped with electrical tape to prevent metal- 561-998-6114 to-metal contact with the camera housing. latam@interlogix.com Ensure that the pigtail wires coming from the camera Web site: are not pinched. www.interlogix.com/mobileview Image is upside down or misaligned on the monitor. - Page 5 Mounting bracket template Use the mounting bracket template to mark the positions of the mounting and cable entry holes on the mounting surface. 2013005 March 2013 © 2013 Interlogix, Inc. www.interlogix.com/mobileview...
Need help?
Do you have a question about the MobileView MVC-7100-29-BL and is the answer not in the manual?
Questions and answers