Table of Contents
Advertisement
HDMI5 Command Ref. (Cont'd)
Extended Control Settings
In the Asynchronous mode of operation, the HDMI5 will transmit state changes as they occur.
This command allows individual control over which state changes will be sent.
This HDMI5 allows control over the following states:
•
Power State changes (On / Off condition).
•
Selection changes (input / output mapping changes).
•
Front Panel modes and intensity changes
•
Front Panel Button Presses.
•
IR codes received.
•
New IR codes learned.
•
Control Settings changes.
Each of the above states can be selectively set to asynchronously transmit their state changes,
or run in the Master / Slave mode. If asynchronous transmit has been disabled for one of the
options, then that option will revert to the Master / Slave mode.
The 'AS' in the "Control Settings" command must be set to '1' to allow any Asynchronous
transmissions, if the 'AS' bit is set to zero, then the HDMI5 will operate solely in the Master /
Slave mode regardless of the settings of this command.
XE settings
Set the enable bits to 'settings'.
XE +settings
Set enable bits indicated in 'settings' to 1.
XE -settings
Reset enable bits indicated in 'settings' to 0.
XE settings,$
Set the control bits to 'settings', save in EEPROM.
XE +settings,$
Set bits indicated in 'settings' to 1, save in EEPROM.
XE -settings,$
Reset bits indicated in 'settings' to 0, save in EEPROM.
XE $
Back up current settings into EEPROM.
XE ?
Query for current settings.
XE
Query for current settings.
2 HDMI5 Component Video Switch
HDMI5 Command Ref. (Cont'd)
Response String:
=XE settings
Where 'settings' is a bitmapped parameter:
Decimal Value
+4096 +2048 +1024 +512 +256 +128 +64 +32 +16
Bit Position
12
11
10
Name
RS2
RS1
RL2 RL1 EQU SWD CTL LMI IRC IRR BTN SEL PWR
Factory Settings:
0
0
0
PWR - 1=Power State has changed.
SEL - 1=Selection (Input / Output Mapping) has changed.
BTN - 1=One or more buttons have been pressed.
IRR - 1=A new IR code has been received.
IRC - 1=New IR codes have been learned.
LMI - 1=Lighting Mode or Intensity Level Settings have changed.
CTL - 1=Control Settings have changed.
SWD - 1=Switching delays have changed.
EQU - 1=Equalization or Bandwidth settings have changed.
RL1 - 1=Auxiliary 1's relay has changed states.
RL2 - 1=Auxiliary 2's relay has changed states.
RS1 - 1=Auxiliary 1 relay's parameters have changed.
RS2 - 1=Auxiliary 2 relay's parameters have changed.
The '$' parameter is a "Backup Control Settings" flag. If it exists, then the current settings will
be backed up in EEPROM, and will remain unchanged through a power failure. Backing up the
"Extended Control Settings" will also backup the "Control Settings".
Input Equalization & Bandwidth
This command allows setting the equalization, bandwidth and control settings of the currently
selected input.
EQU equ,bw,ctl,$
Where:
equ = Indicates the cable length equalization setting (0=Shortest, 15=Longest).
bw = Bandwidth setting. (0=4MHz, 1=3MHz, 2=6Mhz, 3=5MHz).
ctl = Bitmapped control settings (See following bitmap table).
$
= If present, settings are backed up in EEPROM.
Response string:
=EQU equ,bw,ctl
+8
+4
+2
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
1
HDMI5 Component Video Switch
+1
0
1
2
Advertisement
Table of Contents
