Zektor CVS4 User Manual

,home theater switches, high definition component video switch
Hide thumbs Also See for CVS4:

Advertisement

Quick Links

Z E K T O R
H o m e T he at e r Swi tc he s
Digital Video / Component Video / Multichannel Audio
CVS4
High Definition Component Video Switch
Rev 2
07/26/2006

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CVS4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Zektor CVS4

  • Page 1 Z E K T O R H o m e T he at e r Swi tc he s Digital Video / Component Video / Multichannel Audio CVS4 High Definition Component Video Switch Rev 2 07/26/2006...
  • Page 2: Table Of Contents

    C VS4 video switch, however should something go wrong, and war rant y repair wor k is needed, we An Overview of the CVS4 ....3 request that you hold on to the or iginal pack aging mater ials.
  • Page 3: An Overview Of The Cvs4

    An Overview of the CVS4 Front Panel Controls: Front Panel Power I ndicator. Lights up in standby mode. S elec tion LEDs. I ndicate cur rently selec ted inputs. I nput S elec tion Buttons. I nfrared R emote S ensor Window.
  • Page 4: Easy, Simple, Instructions

    (although it can be), any re - mote from an old T V or VCR will wor k just fine. • Using Zektor ’s exclusive I ntelligent-IR™, setup is easy! The POWER Turn to the next chapter for simple instructions...
  • Page 5: Three Simple Steps To A Remote

    Step 1: Put the CVS4 into the Setup Mode Three Simple Steps to a Remote! The C VS4 features Zektor ’s Exclusive I ntelligent-IR™, and with ver y few exceptions can be setup to use any remote you can point at it! Press and hold the Power Button for 4 secs.
  • Page 6: More Remote Options

    Waiting for the '' IR code. remote control button is pressed if the IR '2' - LED Waiting for the '2' IR code. code is compatible with the CVS4. '3' - LED Waiting for the '' IR code. '4' - LED Waiting for the '4' IR code.
  • Page 7: Controlling The Front Panel Lights

    Step 1: Place the CVS4 into the Setup Mode Controlling the Front Panel Lights There are four different front panel light modes available on the C VS4. They are: • Front panel lights automatically fade from br ight to dim Press and hold the Power Button for 4 secs.
  • Page 8: Adjusting The Front Panel Intensity

    Step 1: Place the CVS4 into the Setup Mode Adjusting the Front Panel Intensity The br ight and dim levels of the front panel lights of the C VS4 are user adjustable, allowing the C VS4 to blend into a wide range of lighting conditions.
  • Page 9: Setting The Initial Power On State

    Setting the Initial Power On State Step 1: Set the CVS4 to the preferred initial power on state As long as the C VS4 is plugged in, it will remember the previously selec ted input in standby mode. When powered up by pressing the Power button, it will retur n to that previously selec ted channel.
  • Page 10: Disabling Front Panel Or Remote

    S etup Modes. Even with the front panel disabled you c an per form the above steps, allow- Enable / Disable ing you to once again enable the front panel buttons. Front Panel Buttons Exit Setup Mode 6 CVS4 Component Video Switch CVS4 Component Video Switch...
  • Page 11: Resetting To Factory Defaults

    ‘2’ button... and the ‘’ buttons. After about 4 seconds, the display will flash indicating all parameters have been restored to their factory programmed values.  CVS4 Component Video Switch CVS4 Component Video Switch...
  • Page 12: The Rs-232 Port

    The RS -22 on the C VS4 is the same for mat as a PC-modem, and uses Zektor ’s exclusive K .I.S.S.™ (Keep I t Simple S er ial™) protocol was de - the same t ype cable as a ser ial modem would, which is a standard signed by engineers who have been controlling RS -22 devices for straight through cable.
  • Page 13: The Rear Panel Ir Jack

    The Rear Panel IR Jack The rear panel jack labeled "IR / Z-IN" allows the CVS4 to be controlled by hardwired IR controllers. The signal can be either modulated or unmodulated: 25KHz to 250KHz +3V to +12V MODULATED SIGNAL +3V to +12V UNMODULATED SIGNAL And uses a standard 1/8"...
  • Page 14: Specifications

    90-120VAC, 60Hz, 15W Optional International: 90-264VAC, 47-63Hz, 15W Power Supply: Wall Mount, 9V @ 500ma, U.L. Listed Dimensions: Rack Mountable, 17”W x 6.5”D x 1.75”H Warranty: Two Year Parts and Labor 24 CVS4 Component Video Switch CVS4 Component Video Switch...
  • Page 15 This page lef t intentionally (nea rl y) blank. This page lef t intentionally (nea rl y) blank. 26 CVS4 Component Video Switch CVS4 Component Video Switch...
  • Page 16: Warranty Policy

    Phone: 858-748-8250 us at once and tell us your concer ns, so we may make ever y effor t to Fax: 858-748-8224 satisfy your purchase. E-mail: customerservice@zektor.com Website: www.zektor.com 2 CVS4 Component Video Switch CVS4 Component Video Switch...
  • Page 17 Z E K T O R Z E K T O R 267 Danielson Ct Suite 40 Poway, CA 2064 •74•20 www.zektor.com...

Table of Contents