Related Manuals for Zektor HDVI5
Summary of Contents for Zektor HDVI5
- Page 1 Z E K T O R H o m e T he at e r Swi tc he s Digital Video / Component Video / Multichannel Audio HDVI5 (Picture of HDVI5) Digital Video Switch Rev 1 02/28/2006...
-
Page 2: Table Of Contents
What’s Inside Contents Thank you for your purchase of your HDVI5 H igh D efinition Compo - nent Video Switch. Ever y care has been taken to assure you of a successful installation What’s Inside ........1 and subsequent operations of your new HDVI5 video switch, however should something go wrong, and war rant y repair wor k is needed, we An Overview of the HDVI5 .... -
Page 3: An Overview Of The Hdvi5
Only one of the t wo t ypes of inputs can be ac tive at any time. The HDVI5 will auto -selec t bet ween the t wo t ypes of signals. I f a signal is supplied to both the Coax and Optical inputs, the Coax signal is given pr ior it y. -
Page 4: Easy, Simple, Instructions
To switch bet ween any of the five inputs, simply press the button for the desired input. I f the HDVI5 is in the standby, it will tur n on. The HDVI5 will then switch to the selec ted input, and the associated LED will light to indicate this. - Page 5 • Using any remote to operate the HDVI5 is a simple mat- ter of pair ing up the HDVI5 with the remote. The remote doesn’t have to be a universal remote (although it can be), any remote from an old T V or VCR will wor k just fine.
-
Page 6: Three Simple Steps To A Remote
: Power 1 2 3 4 5 0 8 9 • That ’s it! The HDVI5 will retur n to the state it was in before setup, and will now wor k with your new remote! The new control buttons on your remote are... Press the following sequence of buttons on... -
Page 7: Controlling The Front Panel Lights
To change the front panel lighting mode... Step 1: Enter the Setup Mode • The HDVI5 is placed into the setup mode by pressing and holding the Power button for about seconds. Step 2: Select the Lighting Mode option After ‘’... -
Page 8: Adjusting The Front Panel Intensity
The new intensit y settings are saved in non-volatile memor y and are not affec ted by a power failure. When things look good, press the power button to exit setup mode. 12 HDVI5 Component Video Switch HDVI5 Component Video Switch... -
Page 9: Setting The Initial Power On State
Power button, it will retur n to that previously selec ted channel. However, if power is removed (for instance a plug str ip used to pow- er the HDVI5 is tur ned off ), and then re -applied, the HDVI5’s default Setup the HDVI5 to the initial power on behavior is to enter into the standby mode. -
Page 10: Disabling Front Panel Or Remote
(About seconds.) front panel switches and only operating the HDVI5 with a remote. To enable / disable the front panel switches or remote capabilities... -
Page 11: Changing Switching Delays
Changing Switching Delays The HDVI5 allows adjusting the switching delay times, for Video and Audio, independently. B y default the HDVI5 uses a 200ms video de - lay and no audio delay when switching bet ween channels. The HDMI Press and hold the Power Button until the specifications calls for a minimum of 100ms, some monitors may display goes wild. -
Page 12: Input Cable Length Tuning
Press and hold the desired channel until the HDVI5 enters the cable length tuning The HDVI5 allows for 15 levels of equalization. Using high qualit y mode. DVI or DVI to HDMI conversion cables, the HDVI5 can compensate for cables of up to 20 meters (65f t), on its inputs and still reliably receive a stable, spar k le free image at 1080p. -
Page 13: Bandwidth & Sync Settings
The HDVI5 is a fully digital switch, unlike many similar produc ts, the HDVI5 decodes the DVI / HDMI signal and re - encodes it on the output. This allows it to cor rec t for many non- compliant devices... -
Page 14: Resetting To Factory Defaults
Resetting to Factory Defaults Step 1: Reset All Parameters to Factory Defaults I f, for whatever reason, you’d like to reset your HDVI5 back to its fac - tor y default condition, this is easily done... Step 1: Reset All Parameters to Factory Defaults... -
Page 15: The Rs-232 Port
• The abilit y to read all IR codes sent to the HDVI5 by any re - The por t settings used by the HDVI5 are: mote, even those not used by the HDVI5. Use the HDVI5 to... -
Page 16: The Rear Panel Ir Jack
The Rear Panel IR Jack The rear panel jack labeled "IR / Z-IN" allows the HDVI5 to be controlled by hardwired IR controllers. The signal can be either modulated or unmodulated: 25KHz to 250KHz +3V to +12V MODULATED SIGNAL +3V to +12V UNMODULATED SIGNAL And uses a standard 1/8"... -
Page 17: Specifications
90-120VAC, 60Hz, 15W Optional International: 90-264VAC, 47-63Hz, 15W Power Supply: Wall Mount, 9V @ 1200ma, U.L. Listed Dimensions: Rack Mountable, 17”W x 6.5”D x 1.75”H Warranty: Two Year Parts and Labor 0 HDVI5 Component Video Switch HDVI5 Component Video Switch... -
Page 18: Warranty Policy
Phone: 858-748-8250 us at once and tell us your concer ns, so we may make ever y effor t to Fax: 858-748-8224 satisfy your purchase. E-mail: customerservice@zektor.com Website: www.zektor.com 2 HDVI5 Component Video Switch HDVI5 Component Video Switch... - Page 19 Z E K T O R Z E K T O R 1265 Danielson Ct Suite 01 Poway, CA 206 858•8•8250 www.zektor.com...
Need help?
Do you have a question about the HDVI5 and is the answer not in the manual?
Questions and answers