Lamp Replacement; Manual Operation; Remote Operation - Dimplex SP620 User Manual

This section provides step by step instructions for selecting
a location and preparing the site to install the fireplace into
the following:
Existing Fireplace
1. Make sure that the fire is located on a flat surface.
2. Seal all draughts and vents to prevent chimney debris
from falling onto the Fireplace Insert. Do not install into
an existing fireplace that is prone to dampness.
3. Remove the fire front panel by following the steps as
outlined in 'Lamp Replacement' sections.
4. Locate the 4 fixing holes, position the fire accordingly, and
firmly fix the appliance to the wall using the appropriate
screws - see Fig. 5a.
5. Replace the front panel.
New Support Structure Construction
When planning where to position your purpose built support
structure the following steps must be observed:
1. Place the fire in the desired location to see how it will look
in the room.
2. Mark the desired location for the new support structure in
the room and store the fire in a safe, dry and dust free
location.
3. Using timber studs to support the fire, devise and construct
a suitable means of supporting the product within the
wall partition and provide electrical power for the fire to be
HARD wired. For recommended sizes of height, width
and depth of opening for recess and hole fixing
dimensions for each model - see Table 1 and Fig. 5a.
4. When the structure is complete, remove the front panel of
the fire by following the steps as outlined in 'Lamp
Replacement' sections.
5. Locate the 4 fixing holes, position the fire accordingly, and
firmly fix using the appropriate screws.
6. Replace the front panel.
TABLE 1
A X
1160 1143
NOTE: The appliance should be HARD wired to an electrical
power outlet when placed in a recessed installation.
Please consult a qualified electrician for appropriate wiring
requirements.

Manual Operation

The switches are located at the bottom right side of the
appliance - see Fig. 6.

Remote Operation

The standby switch (S1) must first be turned 'ON'.
Note: It takes some time for the receiver to respond to the
transmitter. DO NOT PRESS the buttons more than once
within two seconds for correct operation.
Manual & Remote Operation
Function Operation
Flame Effect Press the ' I ' button (Switch 3)
The Standby switch must first be turned 'ON' to operate the
appliance manually or by remote control.
Note: It takes some time for the receiver to respond to the
transmitter. DO NOT PRESS the buttons more than once
within two seconds for correct operation.
Y Z
515 146
Status
LED On
To go to the previous settings press the O button.
Pressing the O button on the remote turns off the appliance.
To turn the appliance back On press the I button - see Fig. 8.
To increase or decrease the brightness of the flames, use
the dimmer button or the
To turn off the power the Standby Switch must be turned 'OFF'.

Lamp Replacement

WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE REMOVING LAMPS.
Warning - The lamps reach high temperatures during
operation. For this reason, allow the lamps to cool down
after switching off the appliance.
The front panel will need to be removed in order to change
lamps – see Fig. 9.
Warning - The front panel is heavy and easily damaged.
The front panel is supported at the top by two brackets and
held tight by magnets at the bottom.
To gain access to lamps please apply the following
procedure:
While holding the front panel by its sides with both hands, (1)
carefully tilt the bottom of the frame outwards until free and
then lift the panel up (2) and then away (3) from the main
body - see Fig. 9.
To gain access to the bulbs remove the screws at 'A' to remove
the cover bracket 'X' and the screws at 'B' to remove the
cover bracket 'Y' - see Fig. 10.
To access the bottom bulbs, carefully slide the flexible
rotisserie to one side ensuring that the rubber grommet is
not lost - see Fig. 11.
Remove the defective lamp by unscrewing it - see Fig. 11.
Replace with a 60W E14 SES Clear Candle bulb, rotating it.
Take care not to over-tighten the lamp.
Steps for reassembling the appliance
1. Refit the rotisserie making sure that the rubber grommet
is carefully pushed into the slotted hole on the axial bracket.
2. Replace the cover brackets 'X' and 'Y' - see Fig. 10.
3. Replace the front by aligning the slots at top of the front
frame with the support brackets on the chassis and
ensuring it catches fully on the support brackets.The
magnets on the chassis will hold the front flush to the
main body.
button on the Remote Control.