FLIR D-Series Installation And Operation Manual
D-series
Hide thumbs
Also See for D-Series:
- Installation manual (60 pages) ,
- Installation and operation manual (33 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
Quick Links
D
-
S
e
D
-
S
e
I
n
s
t
a
l
l
a
I
n
s
t
a
l
l
a
444-00001-00-10 Revision 100
r
i
e
s
T
h
e
r
i
e
s
T
h
e
t
i
o
n
a
n
d
t
i
o
n
a
n
d
FLIR Systems, Inc.
70 Castilian Drive
Goleta, CA 93117
Phone: 888.747.FLIR
(888.747.3547)
International: +1.805.964.9797
www.flir.com
Copyright © 2008 FLIR Systems, Inc.
r
m
a
l
C
r
m
a
l
C
O
p
e
r
a
t
i
o
n
O
p
e
r
a
t
i
o
a
m
e
r
a
a
m
e
r
a
M
a
n
u
a
l
n
M
a
n
u
a
l
Page 1 of 32
Advertisement
Table of Contents
Related Manuals for FLIR D-Series
Summary of Contents for FLIR D-Series
- Page 1 FLIR Systems, Inc. 70 Castilian Drive Goleta, CA 93117 Phone: 888.747.FLIR (888.747.3547) International: +1.805.964.9797 www.flir.com 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 1 of 32...
- Page 2 COPYRIGHT Copyright © 2008 by FLIR Systems, Inc. All rights reserved. This publication, or any parts thereof, may not be reproduced in any form without the express written permission of FLIR Systems, Inc.
-
Page 3: Table Of Contents
6.1. IR Imaging Views ....................... 25 6.2 Pelco D and Keyboard Commands ..................26 7. Troubleshooting ........................27 7.1 Caring for your FLIR D-Series Camera ................27 8. Performance Specifications ...................... 28 8.1 FLIR D-Series Camera Dimensions ................... 29 8.2 Default Settings ........................30 9. -
Page 4: Legal Considerations
Figure 5: Installation template (not to scale) ................14 Figure 6: Proper alignment of standoffs for installation of dome enclosure ........ 16 Figure 7: Ring installation (left); D-Series Dome camera installed in ceiling (right) ....16 Figure 8: PC board with DIP switch bank ..................24 Figure 9: Areas radiating heat appear brighter. -
Page 5: Warnings And Cautions
8. Do not install or operate the device in locations that contain flammable and/or explosive objects. 9. Do not try to repair the unit by yourself. FLIR Systems shall not be responsible for any problem caused by unauthorized amendment or repairing. -
Page 6: Introduction
Congratulations! You have purchased one of the most important instruments you can have as part of your security system. The D-Series Thermal Camera is a state-of-the-art thermal imaging system especially suited to accommodate security surveillance of moving objects within a large area. -
Page 7: Pan/Tilt Mechanism
The D-Series Camera features a wide field of view and is capable of providing an image even in absolute darkness. Figure 1 shows the limitations of images obtained with a standard CCTV camera and the advantages provided by the D-Series camera in extreme conditions. -
Page 8: Mounting Options
See sections 3 and 4 for detailed installation instructions. Figure 2: Types of installation CAUTION! The camera should be installed in accordance with local codes and industry- standard safe practices. 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 8 of 32... -
Page 9: Getting Started
If there is any discrepancy between the list and the contents of your shipment, please contact FLIR Systems Customer Support immediately using the contact information at the front of this manual. Please retain the original shipping container and packing materials in case the camera possibly needs to be shipped in the future. -
Page 10: Installation Requirements
3. The installation materials must be capable of supporting well in excess of the weight of the product and accessories. FLIR Systems, Inc. is not responsible for damage or injury that results from an improperly installed camera. -
Page 11: Power On Self-Test
3.2.1 Power On Self-Test The D-Series Camera goes through a self-test process after power on. The camera will tilt up to the top near the trim ring and the dome will perform a full rotation. The self-test is complete when the camera tilts to the home position. -
Page 12: D-Series Camera Connections
3.3 D-Series Camera Connections Figure 4: D-Series Camera wiring connections WARNING: The Green/Yellow Ground wire must be properly connected in order for the camera to operate properly. 3.4 Drop Ceiling Installation (Typical Installation) WARNING! Make sure the Dome Camera and any other related equipment is powered off during installation. - Page 13 Cut an approximately 9 ½ “ diameter hole in the surface where the dome is to be Step 1 mounted using the template provided with the SR-Series camera. A sketch (not to scale) is shown in Figure 5. Cutouts 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 13 of 32...
-
Page 14: Figure 5: Installation Template (Not To Scale)
Turn the trim ring on the unit counter-clockwise to remove it, as shown below. Trim ring Step 3 Secure the mounting board and security chain to the bottom of the dome. 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 14 of 32... - Page 15 Step 5 cutout and the two small plastic standoffs surrounding the mounting screw rest firmly against the ceiling board (they should be flush with the ceiling board). 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 15 of 32...
-
Page 16: Figure 6: Proper Alignment Of Standoffs For Installation Of Dome Enclosure
Slide the trim ring into the slots on the dome edge and turn clockwise to tighten it. Step 7 Figure 7: Ring installation (left); D-Series Dome camera installed in ceiling (right) 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. -
Page 17: Removing The Main Camera Assembly From The Housing Enclosure
Reach inside and lift the catch on the bottom of the inner cylinder. Push down on the cylinder and turn the cylinder counter-clockwise to release it, then pull the cylinder up. 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 17 of 32... - Page 18 You may remove it as well. A safety cable attaches the cylinder to the cylinder bottom and is designed to keep the cylinder from falling of if the maintenance person were to accidentally drop it. 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 18 of 32...
-
Page 19: Steps To Removing The Camera Base For Installation
4.3. Steps to install the base cover 1. To install the base, align the cutout on the base with the pull out tab 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 19 of 32... - Page 20 2. Turn the base clockwise and make sure the locking mechanism engages (you will hear a clicking sound when the locking mechanism sets in place. 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 20 of 32...
-
Page 21: Hard Ceiling Installation (Pendant Mount)
Attach the base to the ceiling using the three screws and wall anchors provided. The wires go up through the central hole in the camera base. Ceiling mounting holes Step 3 Attach the safety cable and ribbon cable. 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 21 of 32... - Page 22 Failure to properly engage the locking mechanism may cause the dome to fall from the base, resulting in damage to the dome and base, and possible personal injury. 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 22 of 32...
-
Page 23: Configuration Options
5. Configuration Options The D-Series Camera comes with defaults set (see Section 5.4: Default Settings). However, you can make the following modifications to the FLIR D-Series Camera: ? Change the electronic wiring connections ? Change the dip switch settings on the PC board... -
Page 24: Changing Dip Switch Settings
RS485 "network", where the Pelco KBD (or similar controller device) uses addressable commands from one access point. This switch needs to be set to the "On" position for the last 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 24 of 32... -
Page 25: Reassembling And Running Self-Check
6. Using Your D-Series Camera 6.1. IR Imaging Views The D-Series Camera is easy to use, but you should take a moment to carefully read this section so you fully understand what you are seeing on your display. While the imagery you will see on the monitor may look like black and white daylight video, it isn’t! A few tips on how to... -
Page 26: Pelco D And Keyboard Commands
16 – 20 Preset 5 Aux On Reserved 25 – 29 Preset 6 – 9 Aux On/Off Reserved 92 Preset ---------- Set Auto Scan Left Hold Preset for >3 seconds 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 26 of 32... -
Page 27: Troubleshooting
Table 3: Troubleshooting Guidelines 7.1 Caring for your FLIR D-Series Camera For lens cleaning use the following materials: ? Optical-grade tissue (e.g., Edmund Industrial Optics part number 52105 or any similar product) ? Pure water (de-ionized or other) -
Page 28: Performance Specifications
Pelco ID Address Shipping Dimensions Size 15” x 15” x 19” (38 cm x 38 cm x 48 cm) Weight 10.7 lbs (4.86 kg) Table 4: Performance Specifications 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 28 of 32... -
Page 29: Flir D-Series Camera Dimensions
8.1 FLIR D-Series Camera Dimensions Figure 10: FLIR D-Series Camera Dimensions (in mm) 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 29 of 32... -
Page 30: Default Settings
8.2 Default Settings The FLIR D-Series Camera comes with a default address of 001 (Table 6), a baud rate of 9600, and default Pelco-D auxiliary command settings (Table 2). NOTE: If you decide to change the settings, FLIR recommends making the change before installation. -
Page 31: Hard Ceiling Mounting Template
Figure 11: Drop Ceiling Mounting Template (not to scale) 9.2 Hard Ceiling Mounting Template Figure 12: Hard Ceiling Mounting Template (not to scale) 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 31 of 32... -
Page 32: Fundamentals Of Infrared
10. Fundamentals of Infrared 444-00001-00-10 Revision 100 Copyright © 2008 FLIR Systems, Inc. Page 32 of 32...
Need help?
Do you have a question about the D-Series and is the answer not in the manual?
Questions and answers