Page 1
User Manual AIMB-562 KIOSK ® Intel LGA775 Core™ 2 Duo mATX Motherboard with Dual VGA/LVDS/DDR2/10 COM/LAN...
Page 2
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
Page 3
Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer's instructions. AIMB-562 KIOSK User Manual...
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
Page 8
It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the AIMB-562 KIOSK, check it for signs of shipping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately.
VGA performance and shares system memory up to 224 MB. Advantech AIMB-562 KIOSK is designed with an Intel 945G/945GC chipset and sup- ports Intel Core 2 Duo processor up to FSB 1066 MHz. A rich I/O connectivity of 10 serial ports, 8 USB 2.0, single GbE LAN and 2 SATA ports.
Board weight: 0.75 kg Jumpers and Connectors Connectors on the AIMB-562 KIOSK motherboard link it to external devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to configure your system for your application.
LVDS power jumper selection1-2:3.3 V 2-3:5 V JBL1 LVDS inverter connector SYS_FAN2 System Fan connector 2 VOLADJ1 Volume adjustment connector AT_SWITCH1 AT Switch power connector Board layout: Jumper and Connector Locations Figure 1.1 Jumper and Connector Location AIMB-562 KIOSK User Manual...
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer’s instructions. AIMB-562 KIOSK User Manual...
1.8.2 CMOS clear (CMOS1) The AIMB-562 KIOSK motherboard contains a jumper that can erase CMOS data and reset the system BIOS information. Normally this jumper should be set with pins 1-2 closed. If you want to reset the CMOS data, set J1 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed.
2-3 closed *default setting 1.8.6 AT switch connector(AT_SWITCH1) The AT switch connector for AIMB-562 KIOSK is default with 1-2 pin closed for only customer who use AT switch power supply. 1.8.7 COM3/7 RS 232/422/485 mode selector (JSETCOM3456/78910) Users can use JSETCOM3456/78910 to select among RS 232/422/485 modes for COM3 and COM7.
1.11 Cache Memory The AIMB-562 KIOSK supports a CPU with one of the following built-in full speed L2 caches: 2048 MB for Intel Core 2 Duo CPU 1024 KB for Pentium dual core...
The parallel port is normally used to connect the motherboard to a printer. The AIMB- 562 KIOSK includes an onboard parallel port, accessed through a 25-pin flat-cable connector, LPT1. Note! Parallel cable is not enclosed in the box as a standard accessory. The order part number is 1700008809. AIMB-562 KIOSK User Manual...
USB Ports (USB12/LAN2_USB34/USB56/USB78) The AIMB-562 KIOSK provides up to eight ports of USB (Universal Serial Bus). The USB interface complies with USB Specification Rev. 2.0 supporting transmission rates up to 480 Mbps and is fuse protected. The USB interface can be disabled in the system BIOS setup.
VGA Connector (VGA1/VGA2) VGA1/VGA2 The AIMB-562 KIOSK includes a VGA interface that can drive conventional CRT dis- plays. VGA1/VGA2 is a standard 15-pin D-SUB connector commonly used for VGA. Pin assignments for CRT connector VGA1/VGA2 are detailed in Appendix B.
COM2 COM 3456/78910 AIMB-562 KIOSK supports ten serial ports - eight RS-232, and two RS-232/422/485 - COM3 and COM7. The user can use JSETCOM3/7 to select among RS 232/422/485 modes for COM3 and COM7. These ports can connect to serial devices, such as a mouse or a printer, or to a communications network.
PS/2 Keyboard and Mouse Connector (KBMS1) KBMS1 Two 6-pin mini-DIN connectors (KBMS1) on the motherboard provide connection to a PS/2 keyboard and a PS/2 mouse, respectively. AIMB-562 KIOSK User Manual...
Front Panel Connectors (JFP1) There are several external switches to monitor and control the AIMB-562 KIOSK. JFP1 5 and 7 Reset switch 1 and 3 Hard drive activity LED 2 and 4 Power/Sleep/Waiting LED 6 and 8 Power switch 2.9.1 Power/Sleep Waiting LED (JFP1) JFP1 pins 2 &...
JFP1 pins 1&2. This connection enables you to turn your computer on and off. 2.10 Line In, Line Out, Mic In Connector (AUDIO1) Line In Line Out Mic In AUDIO1 AIMB-562 KIOSK User Manual...
2.11 Serial ATA Interface (SATA1, SATA2) SATA1, SATA2 AIMB-562 KIOSK features two high performance serial ATA interface (up to 300 MB/ s) which eases cabling to hard drives with thin and long cables. AIMB-562 KIOSK User Manual...
The system can become unstable and might experience difficulty powering up if the power supply is inadequate. You must install a PSU with a higher power rating if you intend to install additional devices. AIMB-562 KIOSK User Manual...
I/O module cable to this connector. Note! For motherboards with the optional HD Audio feature, we recommend that you connect a high-definition front panel audio module to this con- nector to avail of the motherboardís high?definition audio capability. AIMB-562 KIOSK User Manual...
These USB connectors comply with USB 2.0 specification that sup- ports up to 480 Mbps connection speed. Note! The USB module is purchased separately. AIMB-562 KIOSK User Manual...
2.20 LVDS Power Jumper Selection1 (JLVDSPWR1) 2.21 Volume Adjustment Connector (VOLADJ1) Note! The volumn adjustment cable can be used to control the volumn. The cable need bought separately. AIMB-562 KIOSK User Manual...
CPUs from 386 through Pentium and AMD Geode, K7 and K8 (including multiple pro- cessor platforms), and VIA Eden C3 and C7 CPU. You can use Advantech’s utilities to select and install features to suit your designs for customers need.
Set Password Establish, change or disable password. Save & Exit Setup Save CMOS value settings to CMOS and exit BIOS setup. Exit Without Saving Abandon all CMOS value changes and exit BIOS setup. AIMB-562 KIOSK User Manual...
Extended Memory The BIOS POST will determine the amount of extended memory (above 1 MB in CPU’s memory address map) installed in the system. Total Memory This item displays the total system memory size. AIMB-562 KIOSK User Manual...
The eight settings are 6, 8, 10, 12, 15, 20, 24 and 30. – Typematic Delay (Msec) This item sets the keypress time delay before autorepeat begins. Four delay rate options are 250, 500, 750 and 1000. AIMB-562 KIOSK User Manual...
This item enables users to set the DRAM RAS# precharge timing, system default is setting to “Auto” to reference the data from SPD ROM. Precharge delay (tRAS) [Auto] This item allows user to adjust memory precharge time. AIMB-562 KIOSK User Manual...
Page 49
(DVMT). BIOS provides three options: DVMT, FIXED, and Both. DVMT/FIXED Memory Size [128MB] This item allows the user to adjust DVMT/FIXED graphics memory size. Init Display First This item is the setting for start up video output: either from PCI Express or Onboard device. AIMB-562 KIOSK User Manual...
This item enables users to set the OnChip IDE device status, including some of new chipsets also support SATA devices (Serial-ATA). Onboard Device This item enables users to set the Onboard device status, including enabling USB, AC97, and LAN devices. AIMB-562 KIOSK User Manual...
Page 51
This item allows you to determine the active level of the RxD and TxD serial lines. The choices: “Hi, Hi”, “Lo, Lo”, “Lo, H”, and “Hi, Lo”. IR Transmission Delay This item allows you to enable/disable IR transmission delay. The options are “Enabled” and “Disabled”. AIMB-562 KIOSK User Manual...
Select an item and then press <Enabled> to display the configuration options. Note! To enable the TPM function, set the TPM Support item to [Enabled] and then save the change; after rebooting, the TPM configuration menu will show the active options. AIMB-562 KIOSK User Manual...
This item allows user to select system power saving mode. Min Saving Minimum power management. Suspend Mode=1 hr. Max Saving Maximum power management. Suspend Mode=1 min. User Define Allows user to set each mode individually. Suspend Mode= Dis- abled or 1 min ~1 hr. AIMB-562 KIOSK User Manual...
Page 54
Use this to set up the system after power failure. The “Off” setting keeps the system powered off after power failure, the “On” setting boots up the system after failure, and the “Former-Sts” returns the system to the status before power failure. AIMB-562 KIOSK User Manual...
PCI / VGA Palette Snoop [Disabled] This is set to “Disabled” by default. Maximum Payload Size [128] This item shows you the maximum TLP payload size for PCI Express devices. The option is set to [128 bytes] by chipset specification. AIMB-562 KIOSK User Manual...
This shows you the current temperature of system. Current CPU Temperature This shows the current CPU temperature. VCORE and Other Voltages This shows the voltage of VCORE, +3.3 V, +5 V, +12 V, -12 V, VBAT(V), and 5 VSB (V). AIMB-562 KIOSK User Manual...
“Setup” requires a password only to enter Setup. “System” requires the pass- word either to enter Setup or to boot the system. A password can be at most 8 characters long. AIMB-562 KIOSK User Manual...
Page 58
Select Set Password again, and at the “Enter Password” prompt, please don’t enter anything; just press <Enter>. At the”Confirm Password” prompt, again, don’t type in anything; just press <Enter>. Select Save to CMOS and EXIT, type <Y>, then <Enter>. AIMB-562 KIOSK User Manual...
Typing “Y” will quit the BIOS Setup Utility and save user setup values to CMOS. Typing “N” will return to BIOS Setup Utility. 3.2.14 Quit without Saving Note! Typing “Y” will quit the BIOS Setup Utility without saving to CMOS. Typing “N” will return to BIOS Setup Utility. AIMB-562 KIOSK User Manual...
To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for the AIMB-562 KIOSK are located on the software installation CD. The driver in the folder of the driver CD will guide and link you to the utilities and drivers under a Windows system.
Windows XP Driver Setup Insert the driver CD into your system's CD-ROM drive. You can see the driver folder items. Navigate to the "INF" folder and click "setup.exe" to complete the installation of the driver. AIMB-562 KIOSK User Manual...
Insert the driver CD into your system's CD-ROM drive. You can see the driver folders items. Navigate to the "VGA" folder and click "setup.exe" to complete the installation of the drivers for Vista, Windows XP, and Windows 2000. AIMB-562 KIOSK User Manual...
Introduction The AIMB-562 KIOSK has a single/dual Gigabit Ethernet LAN via dedicated PCI Express x 1 bus (Realtek RTL8111C), which offers bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet to operate at 1000 Mbps.
Programming the Watchdog Timer The AIMB-562 KIOSK's watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the pro- grammed period. This section describes the operation of the watchdog timer and how to program it.
Page 75
Unlock W83627DHG Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog timer Lock W83627DHG AIMB-562 KIOSK User Manual...
0. [default=0] Bit 4: Read status of watchdog timer, 1 means timer is “timeout”. Write this address to I/O port 2E (hex) to lock the AA (hex) ----- watchdog timer 2. AIMB-562 KIOSK User Manual...
Mov al,10 Out dx,al ;----------------------------------------------------------- Dec dx ; Lock W83627HG Mov al,0aah Out dx,al Enable watchdog timer and set 5 minutes as timeout interval ;----------------------------------------------------------- Mov dx,2eh ; Unlock W83627HG Mov al,87h Out dx,al Out dx,al AIMB-562 KIOSK User Manual...
Page 78
Enable watchdog timer to be reset by mouse ;----------------------------------------------------------- Mov dx,2eh ; Unlock W83627HG Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- AIMB-562 KIOSK User Manual...
Page 79
Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al AIMB-562 KIOSK User Manual...
Page 80
Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------- Dec dx ; Lock W83627HG Mov al,0aah Out dx,al AIMB-562 KIOSK User Manual...
Parallel Port (LPT1) Table B.1: Parallel Port (LPT1) Signal Signal STROBE* AUTOFD* INIT* SLCTINI* ACK* BUSY SLCT * Low activity USB Header (USB56) Table B.2: USB Header (USB56) Signal Signal USB0_VCC5 USB1_VCC5 USB0_D- USB1_D- USB0_D+ USB1_D+ AIMB-562 KIOSK User Manual...
CPU Fan Power Connector (CPU_FAN1) Table B.12: CPU Fan Power Connector (CPU_FAN1) Signal +12 V DETECT B.13 System Fan Power Connector (SYS_FAN1/ SYS_FAN2) Table B.13: System Fan Power Connector (SYSFAN1/SYSFAN2) Signal +12 V DETECT B.14 Front Panel Connectors (JFP1) AIMB-562 KIOSK User Manual...
Table B.15: Reset Connector (JFP1) Signal RESET B.14.3HDD LED Connector (JFP1) Table B.16: HDD LED Connector (JFP1) Signal IDE LED+ IDE LED- B.14.4ATX Soft Power Switch (JFP1) Table B.17: ATX Soft Power Switch (JFP1) Signal 5 VSB PWR-BTN AIMB-562 KIOSK User Manual...
B.16 ATX Power Connector (EATXPWR1) Table B.19: ATX Power Connector (ATX2) Signal Signal +3.3 V +3.3 V +5 V +5 V 5 VSB 12 V 12 V 3.3 V 3.3 V -12 V PSON -5 V AIMB-562 KIOSK User Manual...
Table B.21: Ethernet 10/100Base-T RJ-45 Port Signal Signal XMT+ XMT- RCV- RCV+ B.18 Line Out, Mic In Connector (AUDIO1) Line Out Mic In B.19 Serial ATA0 (SATA1) Table B.22: Serial ATA0 (SATA1) Signal Signal SATA_0TX+ SATA_0TX- SATA_0RX- SATA_0RX+ AIMB-562 KIOSK User Manual...
JCASE1(Open Case Connector) Table B.33: Case Open Connector(JCASE1) Signal +5VSB ICH_INTRUDER# B.30 DMA Channel Assignments Table B.34: DMA Channel Assignments Channel Function Available Available Floppy disk (8-bit transfer) Available Cascade for DMA controller 1 Available Available Available AIMB-562 KIOSK User Manual...