Advantech AIMB-585 User Manual
  1. Manuals
  2. Brands
  3. Advantech Manuals
  4. Motherboard
  5. AIMB-585
  6. User manual

Advantech AIMB-585 User Manual

Intel xeon e3/core i7/i5/i3 lga1151 microatx with vga/ dvi/edp/dp/hdmi, 6 com, dual lan, ddr4, pcie x 16, pcie x 8 and sataiii
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
AIMB-585
Intel® Xeon® E3/Core™ i7/i5/i3
LGA1151 MicroATX with VGA/
DVI/eDP/DP/HDMI, 6 COM, Dual
LAN, DDR4, PCIe x 16, PCIe x 8
and SATAIII

Advertisement

Table of Contents
loading

Related Manuals for Advantech AIMB-585

Summary of Contents for Advantech AIMB-585

  • Page 1 User Manual AIMB-585 Intel® Xeon® E3/Core™ i7/i5/i3 LGA1151 MicroATX with VGA/ DVI/eDP/DP/HDMI, 6 COM, Dual LAN, DDR4, PCIe x 16, PCIe x 8 and SATAIII...
  • Page 2 The documentation and the software included with this product are copyrighted 2016 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice.
  • Page 3 Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.

  • Page 4: Declaration Of Conformity

    2.3G 14nm LGA1151 PASS QG2/L WG2/QG2/ Intel i3-6100 3.7G 14nm LGA1151 PASS WG2/QG2/ Intel I3-6100TE 2.7G 14nm LGA1151 PASS Intel Pentium® WG2/QG2/ 3.3G 14nm LGA1151 PASS Processor G4400 Intel Pentium® WG2/QG2/ Processor 2.9G 14nm LGA1151 PASS G4400TE AIMB-585 User Manual...
  • Page 5 DDR4 AQD-D4U8GN21-SG PASS 2133 K4A4G085WD DDR4 SEC 543 BCPB Advantech DDR4 AQD-D4U4GN21-SG PASS 2133 K4A4G085WD DDR4 SEC 543 BCPB Advantech 16GB DDR4 AQD-D4U16N21-SE PASS 2133 K4A8G085WB DDR4 SEC 528 K4A8G08 5WB 16GB DDR4 A4D16QB8BNPBSE PASS 2133 BCPB AIMB-585 User Manual...
  • Page 6 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.

  • Page 7: Ordering Information

    It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the AIMB-585, check it for signs of ship- ping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately.
  • Page 8 AIMB-585 User Manual viii...

  • Page 9: Table Of Contents

    Board layout: Jumper and Connector Locations ........5 Figure 1.1 Jumper and Connector Location ........ 5 Figure 1.2 I/O Connectors ............6 AIMB-585 Board Diagram ................. 6 Figure 1.3 AIMB-585 Block Diagram ........... 6 Safety Precautions ..................7 Jumper Settings ..................7 1.8.1 How to Set Jumpers..............
  • Page 10 4.2.2 Software Utility................76 Chapter Chipset Software Installation Utility Before You Begin..................78 Introduction ..................... 78 Windows 8 Driver Setup ................. 79 Chapter VGA Setup ......... 81 Introduction ..................... 82 Windows 8 VGA Driver Installation ............82 AIMB-585 User Manual...
  • Page 11 B.18 Dual port USB3.0 header (USB910) ............. 106 Table B.18:Dual port USB3.0 header (USB910)....... 106 B.19 Dual port USB3.0 header (USB78) ............106 Table B.19:Dual port USB3.0 header (USB78)......106 B.20 COMS Mode selection (JCOMS1) ............107 AIMB-585 User Manual...
  • Page 12 System Fan #3 connector (SYSFAN3) ..........120 Table B.45:System Fan #3 connector (SYSFAN3)....120 B.46 COM1 RI# selection pin header (JSETCOM1_V1)....... 120 Table B.46:COM1 RI# selection pin header (JSETCOM1_V1) 120 B.47 USB VBUS selection for LAN1_USB12, LAN2_USB34, USB561112 AIMB-585 User Manual...
  • Page 13 Case open selection pin header (JCASEOP_SW1)......125 Table B.55:Case open selection pin header (JCASEOP_SW1)125 B.56 COM1_RI# Pin RI# / 5V / 12V selection (JSETCOM1_V1) ....125 Table B.56:COM1_RI# Pin RI# / 5V / 12V selection (JSETCOM1_V1)............ 125 xiii AIMB-585 User Manual...
  • Page 14 AIMB-585 User Manual...

  • Page 15: Chapter 1 General Information

    Chapter General Information...

  • Page 16: Introduction

    3), 1 x PCIe x8 slot (Gen 3), 1 x PCIe x4 slot (Gen 3), 1 x PCIe x1 slot (Gen 3), 2 USB 2.0 ports and 12 USB 3.0 ports.  Standard Micro ATX form factor with industrial features: The AIMB-585 is a full featured Micro ATX motherboard with balanced expandability and perfor- mance.

  • Page 17: Input/Output

    Under Window 7 OS, all of USB 2.0/3.0 ports are not workable before XHCI driver is installed. Suggest to use PS/2 keyboard & mouse for XHCI driver install first.  GPIO: AIMB-585 supports 16-bit GPIO from super I/O for general purpose con- trol application. 1.3.4 Graphics ...

  • Page 18: Jumpers And Connectors

    Board weight: 0.365 kg Jumpers and Connectors Connectors on the AIMB-585 motherboard link it to devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to configure your system for your application.

  • Page 19: Board Layout: Jumper And Connector Locations

    Voltage Display connector SPDIF1 Digital Audio connector 4 x 1 header pitch = 2.54 mm LPC1 Low pin count interface (2 x 7 pin header) Board layout: Jumper and Connector Locations Figure 1.1 Jumper and Connector Location AIMB-585 User Manual...

  • Page 20: Aimb-585 Board Diagram

    Figure 1.2 I/O Connectors AIMB-585 Board Diagram Figure 1.3 AIMB-585 Block Diagram AIMB-585 User Manual...

  • Page 21: Safety Precautions

    1, 2, and 3. In this case you connect either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when set- ting jumpers. AIMB-585 User Manual...

  • Page 22: Cmos Clear (Cmos1)

    1.8.2 CMOS Clear (CMOS1) The AIMB-585 motherboard contains a jumper that can erase CMOS data and reset the system BIOS information. Normally this jumper should be set with pins 1-2 closed. If you want to reset the CMOS data, set CMOS1 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed.

  • Page 23: Jusbpwr1-2 (Usb Power Selection Connector)

    JIR1+JOB1+JWD1: Watchdog Timer Output, OBS Alarm Option, and CIR interface Table 1.7: JIR1+JOB1+JWD1: Watchdog Timer Output and OBS Alarm Connector Pin Name Watch dog reset# output IRRX System reset input# SIO Warning Beep output IRTX SP1 Buzzer Beep input AIMB-585 User Manual...

  • Page 24: Jsetcom2: Com2 Rs232, Rs422, Rs485 Selection

    (3-4) (9-11) (10-12) (15-17) (16-18) RS-485 Mode (1-2) (7-9) (8-10) (13-15) (14-16) 1.8.8 JCASE1: Case Open Sensor The AIMB-585 motherboard contains a jumper that provides a chassis open sensor. The buzzer on the motherboard beeps when the case is opened. AIMB-585 User Manual...

  • Page 25: Jcaseop_Sw1: Case Open Selection Pin Header

    Jumper position for +12V System Memory AIMB-585 has four 288-pin memory sockets for 2133 MHz memory modules with maximum capacity of 64 GB (Maximum 16 GB for each DIMM). AIMB-585QG2/L supports only non-ECC DDR4 memory modules and do not support registered DIMMs (RDIMMs).

  • Page 26: Cache Memory

    1.11 Cache Memory The AIMB-585 supports a CPU with one of the following built-in full speed L3 caches: 8MB for Intel Xeon E3 1275v5 6MB for Intel Xeon E3 1225v5 8MB for Intel Xeon E3 1268Lv5 8MB for Intel Core i7 6700...

  • Page 27: Chapter 2 Connecting Peripherals

    Chapter Connecting Peripherals...

  • Page 28: Introduction

    USB Ports (LAN1_USB12/LAN2_USB34/ USB561112/USB78/USB910/USB1516) The AIMB-585 provides up to 14 USB ports. The USB interface complies with USB Specification Rev 2.0 supporting transmission rates up to 480 Mbps and Rev 3.0 sup- porting transmission rate up to 5 Gbps and is fuse protected. The USB interface can be disabled in the system BIOS setup.

  • Page 29: Usb Power Switch (Jusbpwr1/Jusbpwr2)

    USB Power Switch (JUSBPWR1/JUSBPWR2) AIMB-585 allows users to set USB power between +5 VSB and +5 V. When the jumper is set as +5 V (default 2-3 pin), the board doesn't support wake from S3 via keyboard or mouse. If you need to set it to +5 Vsb, you need to modify the jumper (1- 2 pin) .

  • Page 30: Com1/Dvi-D Connector (Com1+Dvi 1) Connector

    Connector COM1 DVI-D AIMB-585 includes COM1 and DVI interfaces that can drive conventional COM1 and DVI displays. COM1 is a standard 9-pin connector support RS-232. Pin assignments for COM1 and DVI connectors are detailed in Appendix B. AIMB-585 User Manual...

  • Page 31: Serial Ports (Com1~Com6)

    COM1 COM2 COM3~6 AIMB-585 supports six serial ports. COM1, COM2, COM4-6 supports RS-232. COM2 supports RS-232/422/485 (with 5V/12V power). JSETCOM2 is used to select the RS- 232/422/485 mode for COM2. These ports can connect to serial devices, such as a mouse or a printer, or to a com- munications network.

  • Page 32: Display Port (Dp1)

    Display Port (DP1) HDMI AIMB-585 has one external DP/HDMI connector to supports the Display Port panel and HDMI monitor. DP max resolution support to 4096 x 2304 @ 60 Hz HDMI default is support to HDMI 1.2. Can do BOM option to support HDMI 2.0 (4096 x 2160 @ 60 Hz)

  • Page 33: Ps/2 Keyboard And Mouse Connector

    6-pin mini-DIN connectors (KBMS1) is for supporting the PS/2 keyboard and PS/2 mouse by a cable P/N 1703060191. CPU Fan Connector (CPU_FAN1) If a fan is used, this connector supports cooling fans of 500 mA (6 W) or less. AIMB-585 User Manual...

  • Page 34: System Fan Connector (Sysfan1/2/3/4)

    Please notice that, system fan 3 and system fan 4 can't be read rotational speed in BIOS. And system fan 3 will be controlled with system fan 1, system fan 4 will be controlled with system fan 2. AIMB-585 User Manual...

  • Page 35: Front Panel Connectors (Jfp1/Jfp2)

    External speaker (JFP1/SPEAKER) JFP2/SPEAKER is a 4-pin connector for an external speaker. If there is no external speaker, the AIMB-585 provides an onboard buzzer as an alternative. To enable the buzzer, set pins 7 & 10 as closed. AIMB-585 User Manual...

  • Page 36: Power Led And Keyboard Lock Connector

    (on back plane) pins 2-3 closed pins 1-2 closed panel switch via cable jumper setting System On Off ( Windows 7) System Off Slow Flashes (Window 8) Fast flashes Slow flashes 2.11 Line Out, Mic In Connector (AUDIO1) AIMB-585 User Manual...

  • Page 37: Digital Audio Connector (Spdif_Out1)

    This connector is for the S/PDIF audio module to allow digital output sound. Connect one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF module. Note! The S/PDIF module is purchased separately. AIMB-585 User Manual...

  • Page 38: Serial Ata Interface (Sata1 ~ Sata4)

    2.13 Serial ATA Interface (SATA1 ~ SATA4) AIMB-585 features a high performance Serial ATA III interface (up to 600 MB/s) which eases hard drive cabling with thin, space-saving cables. AIMB-585 User Manual...

  • Page 39: 8-Pin Alarm Board Connector (Volt1)

    2.15 PCI Express x16 Slot / PCI Express x 8 AIMB-585 provides a PCIe x16 slot and PCIe x8 slot for users to install add-on cards when their applications require higher graphic performance than the CPU embedded graphics controller can provide.

  • Page 40: Front Panel Audio Connector (Fpaud1)

    I/O module cable. Note! For motherboards with the optional HD Audio feature, we recommend that you connect a high-definition front panel audio module to this con- nector to take advantage of the motherboard’s high definition audio capability. AIMB-585 User Manual...

  • Page 41: Atx Power Connector (Eatxpwr1, Atx12V1)

    Please connect the ATX12V1 connector with the PSU ATX 12V 4- pin connector. For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 180 W. AIMB-585 User Manual...

  • Page 42: Vga (Vga1)

    2.18 VGA (VGA1) AIMB-585 has one 2x 5 pin header on board for VGA (VGA1), but this function is BOM optional. AIMB-585 User Manual...

  • Page 43: General Purpose I/O Connector (Gpio1)

    2.19 General purpose I/O Connector (GPIO1) AIMB-585 User Manual...

  • Page 44: Edp Connector (Edp1)

    2.20 eDP Connector (eDP1) 2.21 EDP Backlight inverter(INV1) AIMB-585 User Manual...

  • Page 45: Bios Operation

    Chapter BIOS Operation...

  • Page 46: Introduction

    AIMB-585 setup screens. BIOS Setup The AIMB-585 Series system has AMI BIOS built in, with a SETUP utility that allows users to configure required settings or to activate certain system features. The SETUP saves the configuration in the FLASH of the motherboard. When the power is turned off, the battery on the board supplies the necessary power to pre- serve the FLASH.

  • Page 47: Main Menu

    System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS format. AIMB-585 User Manual...

  • Page 48: Advanced Bios Features

    3.2.2 Advanced BIOS Features Select the Advanced tab from the AIMB-585 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>...
  • Page 49  Security Device Support [ Disable ] Note! TCG EFI Protocol and INT1A interface won't be available. AIMB-585 User Manual...
  • Page 50 Select ACPI sleep state the system will enter when the SUSPEND button is pressed.  Lock Legacy Resources [ Disabled ] Enables or Disables Lock of Legacy Resources.  S3 Video Repost [ Disabled ] Enable or Disable S3 Video Repost. AIMB-585 User Manual...
  • Page 51 Active Remote Assistance Process [ Disabled ] Trigger CIRA boot.  USB Configure [ Enable ] Enable/Disable USB Configure function.  PET Progress [ Enable ] User can Enable/Disable PET Events progress to receive PET events or not. AIMB-585 User Manual...
  • Page 52 When set to [Enabled], the Watchdog timer will monitor the time taken for each task performed by a software or hardware. – OS Timer [ 0 ] Set OS watchdog timer. – BIOS Timer [ 0] Set BIOS watchdog timer AIMB-585 User Manual...
  • Page 53 3.2.2.4 PCH FM Configuration MEDS BIOS Status Code [ Disable ]  Firmware update Configuration  – ME FW Image Re-Flash [ Disabled ] AIMB-585 User Manual...
  • Page 54 3.2.2.5 NCT6106D Super IO Configuration  Super IO Chip [ NCT6106D ]  Serial Port 1 Configuration AIMB-585 User Manual...
  • Page 55 To select an optimal setting for serial port 1.  Serial Port 2 Configuration – Serial Port [ Enabled ] – Device Settings: IO=2F8h; IRQ =3 – Change Setting [ Auto ] To select an optimal setting for serial port 2. AIMB-585 User Manual...
  • Page 56 Serial Port 3 Configuration – Serial Port [ Enabled ] To “enable or disable” Serial Port 3. – Device Settings: IO=3E8h; IRQ =5 – Change Settings [ Auto ] To select an optimal setting for serial port 3. AIMB-585 User Manual...
  • Page 57  Serial Port 4 Configuration – Serial Port [Enabled] To "enable or disable" serial port 4. – Device Settings: IO=2E8h; IRQ =5 – Change Settings [ Auto ] To select an optimal setting for serial port 4. AIMB-585 User Manual...
  • Page 58  Serial Port 5 Configuration – Serial Port [Enabled] To “enable or disable” serial port 5. – Device Settings: IO=280h; IRQ =7 – Change Settings [ Auto ] To select an optimal setting for serial port 5. AIMB-585 User Manual...
  • Page 59 Serial Port 6 Configuration – Serial Port [ Enabled ] To “enable or disable” serial port 6. – Device Settings: IO=288h; IRQ =7 – Change Setting [ Auto ] To select an optimal setting for serial port 6. AIMB-585 User Manual...
  • Page 60 ACPI Shutdown Temperature [ Disabled ] Use this to set the ACPI shutdown temperature threshold. When the system reaches the shutdown temperature, it will be automatically shut down by ACPI OS to protect the system from overheating damage. AIMB-585 User Manual...
  • Page 61 CPU FAN Mode [ SMART FAN IV Mode ] The item shows you CPU temperature and fan speed (PWM) information.  SYSFAN Mode [ SMART FAN IV Mode ] The item shows you system temperature and fan speed (PWM) information. AIMB-585 User Manual...
  • Page 62  Digital I/O Configuration – Digital I/O Pin 1 - 16 [ Input ] AIMB-585 User Manual...
  • Page 63 3.2.2.7 S5RTC Wake Settings The item allow you enable or disable system wake up on alarm event.  Wake system with Fixed Time [ Disabled ] Note! When enabled, system will wake up on the specified time. AIMB-585 User Manual...
  • Page 64 3.2.2.8 Serial Port Console Redirection  Console Redirection [ Enabled ] Enable or disable the console redirection feature AIMB-585 User Manual...
  • Page 65 3.2.2.9 CPU Configuration  CPU Configuration The item shows you CPU specification and feature, the content could be differ- ent by the different CPU. AIMB-585 User Manual...
  • Page 66 3.2.2.10 SATA Configuration  SATA Controllers [ Enabled ] Enable or disable SATA Function.  SATA Mode [ AHCI ] This can be configured as IDE, AHCI or RAID mode. AIMB-585 User Manual...
  • Page 67 1. Re-install your OS as UEFI Mode 2. Change all of settings above as " Legacy" * Boot option filter-> Legacy Only * Network -> Legacy * Storage -> Legacy * Video -> Legacy * Other PCI devices -> Legacy AIMB-585 User Manual...
  • Page 68  USB Mass Storage Driver Support [ Enabled ]  USB hardware delays and time-outs USB Device transfer & reset time-out and delay setting.  Mass Storage Devices [ Auto ] Shows USB mass storage device information. AIMB-585 User Manual...

  • Page 69: Chipset Configuration Setting

    Users can display a Chipset Setup option by highlighting it using the <Arrow> keys. All Chipset Setup options are described in this section. The Chipset Setup screens are shown below. The sub menus are described on the following pages. AIMB-585 User Manual...

  • Page 70: System Agent (Sa) Configuration

    3.3.1 System Agent (SA) Configuration VT-d [ Enabled ]  Disable or enable VT-d function on MCH. AIMB-585 User Manual...
  • Page 71 Gfx Low Power Mode [ Enabled ]  Note! When BIOS set as " Auto", only single display under DOS. Note! The triple display can only working PASS under Windows 7 and 8, the 2nd and 3rd display can not work under DOS. AIMB-585 User Manual...
  • Page 72 Dual Display CRT+DVI PASS CRT+HDMI PASS CRT+DP PASS CRT+EDP PASS DVI+HDMI PASS DVI+DP PASS DVI+EDP PASS HDMI+DP PASS HDMI+EDP PASS DP+EDP PASS Triple Display DP+HDMI+DVI PASS CRT+HDMI+DVI PASS CRT+DP+HDMI PASS DP+EDP+DVI PASS CRT+EDP+DVI PASS CRT+DP+EDP PASS CRT+DP+DVI PASS AIMB-585 User Manual...
  • Page 73 Enable or disable the control of Active State Power Management on SA side of the DMI Link.  DMI Extended Synch Control [ Disabled ] Enable DMI Extended Synchronization.  DMI De-emphasis Control [ -3.5 dB ] Configure the De-emphasis control on DMI  DMI IOT [ Disabled ] AIMB-585 User Manual...
  • Page 74 Root Port Preset Value Per lane for Gen3 Equalization.  PEG Gen3 Endpoint Preset Value each Lane Endpoint Preset Value Per lane for Gen3 Equalization.  PEG Gen3 Endpoint Hint Value each Lane Endpoint Hint Value Per lane for Gen3 Equalization. AIMB-585 User Manual...
  • Page 75 MMIO length of installed graphic controller.  Retrain on Fast Fall [Enabled] Enable or disable Retrain on Fast Fall.  Memory Remap [Enabled] Enable or disable Memory remap.  Fast Boot [Enabled] Enable or disable Fast Boot support. AIMB-585 User Manual...

  • Page 76: Pch-Io Configuration

    Enable or disable PCIE to wake the system from S5.  High Precision Timer Enable or Disable High Precision Timer.  State After G3 [ Power Off ] This item allows users to select off, on and last state. AIMB-585 User Manual...
  • Page 77 The control of Active State Power Management on both NB side and SB side of the DMI Link.  Peer Memory Write Enable [Disabled]  PCIe-USB Glitch W/A [ Disabled ] PCIe-USB Glitch W/A for bad USB device(s) connected behind PCIE/PEG Port. AIMB-585 User Manual...
  • Page 78 Set the ASPM Level: Force L0s - Force all links to L0s State : AUTO - BIOS auto configure : DISABLE - Disables ASPM – L1 Substates PCI Express L1 Substates settings. – PCIe Speed [ Auto ] Select PCI Express port speed. AIMB-585 User Manual...
  • Page 79 Set the ASPM Level: Force L0s - Force all links to L0s State : AUTO - BIOS auto configure : DISABLE - Disables ASPM – L1 Substates PCI Express L1 Substates settings. – PCIe Speed [ Auto ] Select PCI Express port speed. AIMB-585 User Manual...
  • Page 80 Set the ASPM Level: Force L0s - Force all links to L0s State : AUTO - BIOS auto configure : DISABLE - Disables ASPM – L1 Substates PCI Express L1 Substates settings. – PCIe Speed [ Auto ] Select Mini PCI Express port speed. AIMB-585 User Manual...
  • Page 81 3.3.2.2 USB Configuration  USB Preconditon [ Disabled ] To enable or disable precondition work on USB host controller for faster enu- meration. AIMB-585 User Manual...

  • Page 82: Security Setting

    Select this option and press <ENTER> to access the sub menu, and then type in the password. Set the Administrator password.  User Password Select this option and press <ENTER> to access the sub menu, and then type in the password. Set the User Password. AIMB-585 User Manual...

  • Page 83: Boot Setting

    Quiet Boot [ Disabled ] If this option is set to disabled, the BIOS displays normal POST messages. If enabled, an OEM logo is shown instead of POST messages.  Boot Option #1/#2 Choose boot priority from boot device AIMB-585 User Manual...

  • Page 84: Save & Exit Configuration

    Select Exit Saving Changes from the Exit menu and press <Enter>. The fol- lowing message appears: Save Configuration Changes and Exit Now? [Ok] [Cancel] Select Ok or cancel.  Discard Changes and Reset Select this option to quit Setup without making any permanent changes to the system configuration. AIMB-585 User Manual...
  • Page 85 Defaults if the user's computer is experiencing system configuration problems. Select Restore Defaults from the Exit menu and press <Enter>.  Save as User Default Save the all current settings as a user default.  Restore User Default Restore all settings to user default values. AIMB-585 User Manual...
  • Page 86 AIMB-585 User Manual...

  • Page 87: Software Introduction & Service

    Chapter Software Introduction & Service...

  • Page 88: Introduction

    Introduction The mission of Advantech Embedded Software Services is to "Enhance quality of life with Advantech platforms and Microsoft® Windows® embedded technology." We enable Windows® Embedded software products on Advantech platforms to more effectively support the embedded computing community. Customers are freed from the hassle of dealing with multiple vendors (hardware suppliers, system integrators, embedded OS distributors) for projects.
  • Page 89 System Throttling Refers to a series of methods for reducing power consump- tion in computers by lowering the clock frequency. This API allows the user to adjust the clock from 87.5% to 12.5%. AIMB-585 User Manual...

  • Page 90: Software Utility

    Monitoring is a utility for customers to monitor system health, like voltage, CPU and system temperature and fan speed. These items are important to a device, if critical errors occur and are not solved immediately, permanent damage may be caused. AIMB-585 User Manual...

  • Page 91: Chipset Software Installation Utility

    Chapter Chipset Software Installation Utility...

  • Page 92: Before You Begin

    Before You Begin To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for AIMB-585 are located on Advantech website. (http://support.advantech.com/Support/.) Updates are provided via Service Packs from Microsoft*.

  • Page 93: Windows 8 Driver Setup

    Windows 8 Driver Setup When enter the website of Advantech, then search product AIMB-585. There is "Chipset" driver inside. AIMB-585 User Manual...
  • Page 94 AIMB-585 User Manual...

  • Page 95: Vga Setup

    Chapter VGA Setup...

  • Page 96: Introduction

    Before installing this driver, make sure the CSI utility has been installed in your system. See Chapter 5 for information on installing the CSI utility. When enter the website of Advantech, then search product AIMB-585. There is "Graphic" driver inside. AIMB-585 User Manual...

  • Page 97: Lan Configuration

    Chapter LAN Configuration...

  • Page 98: Introduction

    Introduction The AIMB-585 has dual Gigabit Ethernet LANs via dedicated PCI Express x1 lanes (Intel I219LM (LAN1) and I211AT (LAN2)) that offer bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet at 1000 Mbps.

  • Page 99: Windows® 8 Driver Setup (Intel I219Lm/ Intel I211At)

    Windows® 8 Driver Setup (Intel I219LM/ Intel I211AT) When enter the website of Advantech, then search product AIMB-585. There is "LAN" driver inside. AIMB-585 User Manual...
  • Page 100 AIMB-585 User Manual...
  • Page 101 Appendix Programming the Watchdog Timer...

  • Page 102: Appendix A Programming The Watchdog Timer

    Programming the Watchdog Timer AIMB-585's watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to program it.
  • Page 103 Unlock NCT6106D Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog timer Lock NCT6106D AIMB-585 User Manual...

  • Page 104: Table A.1: Watchdog Timer Registers

    Bit 5: Write 1 to generate a timeout signal immedi- ately and automatically return to 0. [default=0] Bit 4: Read status of watchdog timer, 1 means timer is “timeout”. Write this address to I/O port 2E (hex) to lock the AA (hex) ----- watchdog timer 2. AIMB-585 User Manual...

  • Page 105: Example Program

    Inc dx Mov al,10 Out dx,al ;----------------------------------------------------------- Dec dx ; Lock NCT6106D Mov al,0aah Out dx,al Enable watchdog timer and set 5 minutes as timeout interval ;----------------------------------------------------------- Mov dx,2eh ; Unlock NCT6106D Mov al,87h Out dx,al Out dx,al AIMB-585 User Manual...
  • Page 106 Enable watchdog timer to be reset by mouse ;----------------------------------------------------------- Mov dx,2eh ; Unlock NCT6106D Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- AIMB-585 User Manual...
  • Page 107 Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al AIMB-585 User Manual...
  • Page 108 Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------- Dec dx ; Lock NCT6106D Mov al,0aah Out dx,al AIMB-585 User Manual...

  • Page 109: Appendix B Pin Assignments

    Appendix Pin Assignments...

  • Page 110: Keyboard & Mouse Connector (Kbms1)

    Digital Visual Interface connector (DVI1) Table B.2: Digital Visual Interface connector (DVI1) Signal Signal TMDS D2- TMDS D2+ VCC (+5V) Hot plug detect TMDS D0- DDC CLK TMDS D0+ DDC DAT TMDS D1- TMDS D1+ TMDS CLK+ TMDS CLK- AIMB-585 User Manual...

  • Page 111: Com1 Connector (Com1)

    RXD [1] RTS# [1] TXD [1] CTS# [1] DTR# [1] RI# [1] Video Graphics Array connector (VGA1) Table B.4: Video Graphics Array connector (VGA1) Signal Signal DDC DAT DDC CLK VSYNC GREEN Advantech define HSYNC BLUE VCC (+5V) AIMB-585 User Manual...

  • Page 112: Displayport1(Up) + Hdmi1(Down) Stack Connector (Dp1+Hdmi1)

    ML0- CONFIG1 ML1+ AUX+ ML1- ML2+ AUX- Hot plug detect ML2- ML3+ DP_PWR (+3.3V) Signal Signal TMDS D2+ TMDS CLK- TMDS D2- TMDS D1+ TMDS D1- TMDS D0+ VCC (+5V) TMDS D0- Hot plug detect TMDS CLK+ AIMB-585 User Manual...

  • Page 113: Universal Serial Bus Port 5 / 6 / 11 / 12 (Usb561112)

    VBUS (*) VBUS (*) D-_6 D-_5 D+_6 D+_5 RX-_6 RX-_5 RX+_6 RX+_5 TX-_6 TX-_5 TX+_6 TX+_5 (*) Depends on JUSBPWR2 Jump Setting Signal Signal VBUS (*) VBUS (*) D-_12 D-_11 D+_12 D+_11 (*) Depends on JUSBPWR2 Jump Setting AIMB-585 User Manual...

  • Page 114: B.7 Rj45 + Usb3.0 Stack Connector (Lan1_Usb12)

    Table B.7: RJ45 + USB3.0 stack connector (LAN1_USB12) Signal Signal VBUS (*) VBUS (*) D-_1 D-_2 D+_1 D+_2 RX-_1 RX-_2 RX+_1 RX+_2 TX-_1 TX-_2 TX+_1 TX+_2 (*) Depends on JUSBPWR2 Jump Setting Signal Signal MDI_0+ MDI_2+ MDI_0- MDI_2- MDI_1+ MDI_3+ MDI_1- MDI_3- AIMB-585 User Manual...

  • Page 115: Rj45 + Usb3.0 Stack Connector (Lan2_Usb34)

    Table B.8: RJ45 + USB3.0 stack connector (LAN2_USB34) Signal Signal VBUS (*) VBUS (*) D-_3 D-_4 D+_3 D+_4 RX-_3 RX-_4 RX+_3 RX+_4 TX-_3 TX-_4 TX+_3 TX+_4 (*) Depends on JUSBPWR2 Jump Setting Signal Signal MDI_0+ MDI_2+ MDI_0- MDI_2- MDI_1+ MDI_3+ MDI_1- MDI_3- AIMB-585 User Manual...

  • Page 116: Usb Power Selection Header #2 (Jusbpwr2)

    Table B.10: LAN LED (LANLED1) Signal Signal LAN1 ACTIVE LAN2 ACTIVE LAN1 LED PWR LAN2 LED PWR LAN1 LINK1000 LAN2 LINK1000 LAN1 LINK100 LAN2 LINK100 +3.3VSB B.11 HD Audio interface (SPDIF1) Table B.11: HD Audio interface (SPDIF1) Signal SPDIF OUT AIMB-585 User Manual...

  • Page 117: Audio Amplifier Output Pin Header (Jamp1)

    AUDIO GND AMP_OUT-L AUDIO GND AMP_OUT-R B.13 Front panel audio pin header (FPAUD1) Table B.13: Front panel audio pin header (FPAUD1) Signal Signal MIC IN-L MIC IN-R FPAUD_DETECT# LINE OUT-R SENSE R1 SENSE LINE OUT-L SENSE R2 AIMB-585 User Manual...

  • Page 118: Embedded Displayport (Edp1)

    AUX+ Hot plug detect EDP Power (*) EDP Power (*) (*) Depends on JEDP1 Jump Setting B.15 Voltage selector for EDP1 connector (JEDP1) Table B.15: Voltage selector for EDP1 connector (JEDP1) Signal Signal +12V EDP1 VDD +3.3V AIMB-585 User Manual...

  • Page 119: Edp Backlight Inverter Power Connector (Inv1)

    EDP Backlight inverter power connector (INV1) Table B.16: EDP Backlight inverter power connector (INV1) Signal +12V BKL EN BKL CTRL B.17 USB Power selection header #1 (JUSBPWR1) Table B.17: USB Power selection header #1 (JUSBPWR1) Signal +3.3VSB Advantech define +3.3 AIMB-585 User Manual...

  • Page 120: Dual Port Usb3.0 Header (Usb910)

    (*) Depends on JUSBPWR1 Jump Setting B.19 Dual port USB3.0 header (USB78) Table B.19: Dual port USB3.0 header (USB78) Signal Signal VBUS (*) D+_8 RX-_7 D-_8 RX+_7 TX+_8 TX-_7 TX-_8 TX+_7 RX+_8 D-_7 RX-_8 D+_7 VBUS (*) AIMB-585 User Manual...

  • Page 121: Coms Mode Selection (Jcoms1)

    (*) Depends on JUSBPWR1 Jump Setting B.20 COMS Mode selection (JCOMS1) Table B.20: COMS Mode selection (JCOMS1) Signal VBAT RTC RESET# B.21 Alarm Board/CMM Power Connector (VOLT1) Table B.21: Alarm Board/CMM Power Connector (VOLT1) Signal +5VSB +3.3V -12V +12V AIMB-585 User Manual...

  • Page 122: System Fan #2 Connector (Sysfan2)

    SPI Pin Header (SPI_CN1) Table B.23: SPI Pin Header (SPI_CN1) Signal Signal +3.3VSB SCLK MISO MOSI B.24 System Fan #4 connector (SYSFAN4) Table B.24: System Fan #4 connector (SYSFAN4) Signal SYSTEM FAN VCC SYSTEM FAN SPEED SYSTEM FAN PWM AIMB-585 User Manual...

  • Page 123: Power Led And Keyboard Lock Pin Header (Jfp2)

    LED Power Keyboard Lock B.26 Power switch/HDD LED/SMBus/Speaker pin header (JFP1) Table B.26: Power switch/HDD LED/SMBus/Speaker pin header (JFP1) Signal Signal HDD LED+ Power Button+ SPK_P2 HDD LED- Power Button- SPK_P3 SMB_DATA System Reset+ SPK_P4 SMB_CLK System Reset- AIMB-585 User Manual...

  • Page 124: Cir Interface, Watchdog Timer Output And Obs Beep (Jir1+Jobs1+Jwdt1)

    IRTX SP1 Buzzer Beep input B.28 AT/ATX Mode selection (PSON1) Table B.28: AT/ATX Mode selection (PSON1) Signal +3.3V B.29 SMBus connector from PCH (SMBUS1) Table B.29: SMBus connector from PCH (SMBUS1) Signal +5VSB SMB CLK SMB DAT AIMB-585 User Manual...

  • Page 125: Serial Ata Interface Connector (Sata1 / Sata2 / Sata3 / Sata4)

    B.30 Serial ATA interface connector (SATA1 / SATA2 / SATA3 / SATA4) Table B.30: Serial ATA interface connector (SATA1 / SATA2 / SATA3 / SATA4) Signal AIMB-585 User Manual...

  • Page 126: Minipcie, Msata Connector (Minipcie1)

    Reserved +1.5V CLKREQ# Reserved Reserved REFCLK- Reserved REFCLK+ Reserved Reserved Reserved Reserved DISABLE# DETECT# RESET# PCIE_RX+ +3.3Vaux PCIE_RX- +1.5V SMB_CLK PCIE_TX- SMB_DATA PCIE_TX+ USB_D- USB_D+ +3.3Vaux +3.3Vaux Reserved V1.2_DETECT# LED_WLAN# Reserved Reserved Reserved +1.5V Reserved MSATA_DETECT# +3.3Vaux AIMB-585 User Manual...
  • Page 127 Signal Reserved +3.3V Reserved Reserved +1.5V Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved DETECT# Reserved +3.3V +1.5V SMB_CLK SMB_DATA Reserved Reserved +3.3V +3.3V Reserved Reserved Reserved Reserved Reserved Reserved +1.5V Reserved MSATA_DETECT# +3.3V AIMB-585 User Manual...

  • Page 128: Cmos Battery Connector (Bat1)

    B.33 Dual port USB3.0 header (USB1516) Table B.33: Dual port USB3.0 header (USB1516) Signal Signal VBUS (*) D+_15 RX-_16 D-_15 RX+_16 TX+_15 TX-_16 TX-_15 TX+_16 RX+_15 D-_16 RX-_15 D+_16 VBUS (*) (*) Depends on JUSBPWR1 Jump Setting AIMB-585 User Manual...

  • Page 129: Com3 ~ Com6 Box Header (Com3456)

    CTS# [4] DTR# [4] RI# [4] DCD# [5] DSR# [5] RXD [5] RST# [5] TXD [5] CTS# [5] DTR# [5] RI# [5] DCD# [6] DSR# [6] RXD [6] RST# [6] TXD [6] CTS# [6] DTR# [6] RI# [6] AIMB-585 User Manual...

  • Page 130: Atx 24Pin Power Connector (Eatxpwr1)

    +12V +3.3V B.36 16-bits General Purpose I/O pin header (GPIO1) Table B.36: 16-bits General Purpose I/O pin header (GPIO1) Signal Signal GPIO0 GPIO8 GPIO1 GPIO9 GPIO2 GPIO10 GPIO3 GPIO11 GPIO4 GPIO12 GPIO5 GPIO13 GPIO6 GPIO14 GPIO7 GPIO15 AIMB-585 User Manual...

  • Page 131: Com2 Box Header (Com2)

    RST# [2] TXD [2] CTS# [2] DTR# [2] RI# [2] B.38 Low pin count interface connector (LPC1) Table B.38: Low pin count interface connector (LPC1) Signal Signal CLK (24MHz) RESET# FRAME# +3.3V SMB CLK SERIRQ SMB DAT +5VSB AIMB-585 User Manual...

  • Page 132: Com2 Rs232,Rs422,Rs485 Selection Pin Header (Jsetcom2)

    DCDB SOUT [2] COM2_DCD# COM2_SOUT COM2_TXD485- COM2_RXD485+ SIN [B] DTR [B] COM2_SIN COM2_DTR# COM2_TXD485+ COM2_RXD485- B.40 Case Open selection pin header (JCASEOP_SW1) Table B.40: Case Open selection pin header (JCASEOP_SW1) Signal Normal Open Advantech define Normal Close AIMB-585 User Manual...

  • Page 133: Case Open Connector (Jcase1)

    CPU FAN connector (CPUFAN1) Table B.42: CPU FAN connector (CPUFAN1) Signal CPU FAN VCC CPU FAN SPEED CPU FAN PWM B.43 ATX 4 Pin main power connector (ATX12V1) Table B.43: ATX 4 Pin main power connector (ATX12V1) Signal +12V +12V AIMB-585 User Manual...

  • Page 134: System Fan #1 Connector (Sysfan1)

    Table B.45: System Fan #3 connector (SYSFAN3) Signal SYSTEM FAN VCC SYSTEM FAN SPEED SYSTEM FAN PWM B.46 COM1 RI# selection pin header (JSETCOM1_V1) Table B.46: COM1 RI# selection pin header (JSETCOM1_V1) Signal Signal RI# [1] Advantech define Advantech define +12V Advantech define AIMB-585 User Manual...

  • Page 135: (Jusbpwr2)

    Set USB VBUS as +5V B.48 USB VBUS selection for USB78, USB910, USB1516 (JUSBPWR1) Table B.48: USB VBUS selection for USB78, USB910, USB1516 (JUSBPWR1) Function Jumper Setting Set USB VBUS as +5VSB (Default) Set USB VBUS as +5V AIMB-585 User Manual...

  • Page 136: Voltage Selection For Edp1 Connector (Jedp1)

    Table B.49: Voltage selection for EDP1 connector (JEDP1) Function Jumper Setting Jumper position for +3.3V (Default) Jumper position for +5V Jumper position for +12V B.50 CMOS clear (JCOMS1) Table B.50: CMOS clear (JCOMS1) Function Jumper Setting Keep CMOS Data (Default) Clear CMOS Data AIMB-585 User Manual...

  • Page 137: Pwrbtn#/ Reset#/Hdd Led / Serial Bus From Hw Monitor Ic/Internal Buzzer / External Speaker Header (Jfp1)

    CIR interface, Watchdog timer output and OBS beep (JIR1+JOBS1+JWDT1) Table B.52: CIR interface, Watchdog timer output and OBS beep (JIR1+JOBS1+JWDT1) Function Jumper Setting Watchdog Timer Output (4-6) (Default) OBS BEEP(8-10) (Default) Watchdog Timer Disable (2-4) OBS BEEP(8-10) (Default) AIMB-585 User Manual...

  • Page 138: At / Atx Mode Selection (Pson1)

    COM2 RS232?RS422?RS485 selection pin header (JSETCOM2) Table B.54: COM2 RS232?RS422?RS485 selection pin header (JSETCOM2) Function Jumper Setting RS-232 Mode (Default) (5-6) (7-9) (8-10) (13-15) (14-16) RS-422 Mode (3-4) (9-11) (10-12) (15-17) (16-18) RS-485 Mode (1-2) (7-9) (8-10) (13-15) (14-16) AIMB-585 User Manual...

  • Page 139: Case Open Selection Pin Header (Jcaseop_Sw1)

    B.56 COM1_RI# Pin RI# / 5V / 12V selection (JSETCOM1_V1) Table B.56: COM1_RI# Pin RI# / 5V / 12V selection (JSETCOM1_V1) Function Jumper Setting Jumper position for RI# (Default) Jumper position for +5V Jumper position for +12V AIMB-585 User Manual...
  • Page 140 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2016...
  • Page 141 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Advantech AIMB-585QG2-00A1E...

Table of Contents