Cornelius ED 300 BC Operator's Manual
  1. Manuals
  2. Brands
  3. Cornelius Manuals
  4. Beverage Dispenser
  5. ED 300 BC
  6. Operator's manual

Cornelius ED 300 BC Operator's Manual

Ice/beverage dispenser
Hide thumbs Also See for ED 300 BC:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual, Installation Manual
Telephone (800) 238–3600
Operator's Manual
ICE/BEVERAGE DISPENSER
Model: ED 300 BC
IMPORTANT:
TO THE INSTALLER.
It is the responsibility of
the Installer to ensure that
the water supply to the
dispensing equipment is
provided with protection
against backflow by an air
gap as defined in
ANSI/ASME A112.1.2-1979;
or an approved vacuum
breaker or other such
method as proved effective
by test.
Water pipe connections
and fixtures directly
connected to a potable
water supply shall be
sized, installed, and
maintained according to
Federal, State, and Local
Codes.
Part No.92059OPR
March 24, 2004
Revised: N/A
Revision: A
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
This Manual must be read and understood before installing or operating this equipment
IMI CORNELIUS INC; 2004
IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303
Facsimile (800) 535–4231
PRINTED IN U.S.A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ED 300 BC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Cornelius ED 300 BC

Summary of Contents for Cornelius ED 300 BC

  • Page 1 IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303 Telephone (800) 238–3600 Facsimile (800) 535–4231 Operator’s Manual ICE/BEVERAGE DISPENSER Model: ED 300 BC IMPORTANT: TO THE INSTALLER. It is the responsibility of the Installer to ensure that the water supply to the...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Page MAINTENANCE ............DAILY .

  • Page 3: Maintenance

    MAINTENANCE The following dispenser maintenance should be performed at the intervals indicated: DAILY (or as required) Remove foreign material from vending area drip tray to prevent drain blockage. WEEKLY (or as required) Clean vending area. Check for proper water drainage from the vending area drip tray. MONTHLY Clean and sanitize the hopper interior (see CLEANING INSTRUCTIONS).

  • Page 4: Dispenser

    DISPENSER 1. CLEANING EXTERIOR SURFACES Important: Perform the following daily. Remove the cup rest from drip tray. Wash the drip tray with soap solution. Rinse with clean water and allow solution to run down the drain. Wash cup rest with soap solution and rinse in clean water. Install the cup rest into the drip tray. Clean all exterior surfaces with soap solution and rinse in clean water.

  • Page 5: Beverage System If Applicable

    BEVERAGE SYSTEM IF APPLICABLE WARNING: Disconnect Power Before Cleaning! Do not use metal scrapers, sharp objects or abrasives on the ice storage hopper, top cover and the agitator disk, as damage may result. Do not use solvents or other cleaning agents, as they may attack the plastic material. Soap solution - use a mixture of mild detergent and warm 100 degrees F potable water.
  • Page 6 Sanitize syrup lines, B-I-B Systems Remove all the quick disconnects from all the B-I-B containers. Fill a suitable pail or bucket with soap solution. Submerge all disconnects (gas and liquid) in the soap solution and then clean them using a nylon bristle brush.

  • Page 7: Removal And Replacement Of Agitators

    REMOVAL AND REPLACEMENT OF AGITATORS RIGHT HAND AGITATOR LEFT HAND WITH HOLE IN UPRIGHT AGITATOR O–RING COUNTER CLOCKWISE CLOCKWISE ROTATION ROTATION FRONT (VALVE SIDE) VIEW FROM TOP OF DISPENSER To Remove Agitators For Cleaning 1. Lift agitator and disc from unit.. 2.

  • Page 8: Troubleshooting

    TROUBLESHOOTING IMPORTANT: Only qualified personnel should service internal components or electrical wiring. WARNING: If repairs are to be made to a product system, remove quick disconnects from the applicable product tank, then relieve the system pressure before proceeding. If repairs are to be made to the CO system, stop dispensing, shut off the CO supply, then relieve the...

  • Page 9: Beverage Not Sweet Enough

    Trouble Probable Cause BEVERAGE NOT SWEET ENOUGH. Empty syrup tank. Faucet brix requires adjusting. BEVERAGES NOT COLD (UNITS WITH BUILT–IN Unit standing with no ice in hopper – no ice in COLD PLATE). cold plate cabinet. AGITATORS TURN IN OPPOSITE DIRECTIONS This is normal and is necessary for uniform ice agitation.

  • Page 11: Warranty

    WARRANTY IMI Cornelius Inc. warrants that all equipment and parts are free from defects in material and work- manship under normal use and service. For a copy of the warranty applicable to your Cornelius prod- uct, in your country, please write, fax or telephone the IMI Cornelius office nearest you. Please provide the equipment model number, serial number and the date of purchase.
  • Page 12 IMI CORNELIUS INC. CORPORATE HEADQUARTERS: One Cornelius Place Anoka, Minnesota 55303-6234 (763) 421-6120 (800) 238-3600 92059OPR...

Table of Contents