About This Pump; Safety - ProMinent Makro TZ Operating Instructions Manual

Add-on pumps The ProMinent
Double-head version The double head versions are fitted with a second liquid end which operates in counter cycle
Correct use
of equipment Use • The pump may be used for metering liquid media only!
Safety instructions
ProMinent ®
1

About this pump

ProMinent ® Makro TZ dosing pumps are supplied with a 1.5 kW multi-voltage three-phase motor
as standard (TZMb, TZMa: 0.75 kW). The stroke length can be adjusted between 0...20 mm
(TZMb: 0...10 mm, TZMa: 0...6/9 mm). The acrylic resin coated cast housing can be combined
with up to 16 liquid ends and 5 reduction ratios. Liquid ends are available in different material
combinations to suit the particular dosing media. The Makro TZMb is fitted with a composite
diaphragm with diaphragm rupture indicator as standard. Under defined conditions and with
correct installation, the reproducibility of the dosing with the TZKa is better than  0.5 % in the
stroke length range from 10 %- 100 % and better than  1 % for the TZHa (TZMb, TZMa:  2 %
between 30 % - 100 %).
®
Makro TZ add-on metering pump can be combined with the Makro TZ main
power end to produce a duplex/multiplex pump. A main power end can be combined with up to
four add-on power ends. One power end can be used as both a single and a double head version.
(Boxer principle).
2

Safety

• The pump can be operated with the appropriate motor (TZMb, TZMa, TZHa, TZKa) and the
appropriate float switch and cable on the diaphragm rupture indicator (TZHa) in areas with
potentially explosive atmospheres in Zone 1, device category II 2G of explosion group II C in
accordance with the European Directives. In this case, the pumps must have the appropriate
identifications in accordance with ATEX Directive 94/9/EC. The explosion group, category and
protection class on the identification must correspond with or be better than the given
conditions in the envisaged application.
• All other applications and modifications are prohibited!
• Pumps without the appropriate rating plate and the appropriate EC Declaration of Conformity
for areas with potentially explosive atmospheres must never be operated in areas with
potentially explosive atmospheres.
• The pumps with piston liquid ends are not suitable for metering life-threatening liquids.
• The pump is not suitable for metering gaseous media or solids.
• The pump may be used only within the stated pressure range.
• Please observe general limitations with regard to viscosity limits, chemical resistance and
density and the stated ambient conditions.
• It is essential that you read this operating instruction manual together with the "General
Operating Instructions for ProMinent
concerning assembly, installation and maintenance!
• The pump is to be operated by appropriately trained personnel only.
WARNING
• EX pump only: Always observe the "Important supplements for dosing pumps in EX
areas" section of the "General Operating Instruction for ProMinent
Metering Pumps and Hydraulic Accessories"!
• The pump starts to operate as soon as it is connected to the mains.
Ensure that hazardous media cannot leak out.
• The pump has no on/off switch.
In the event of an electrical fault, unplug the mains cable or switch off the system at the
emergency off-switch.
• Unplug the cable from the mains before working on the pump!
• Always depressurise the liquid end before working on the pump!
• Before working on the pump, empty the liquid end and rinse out if it has been used with
hazardous or unknown chemicals.
• Always wear suitable protective equipment when working on a liquid end which has
been used with hazardous or unknown chemicals.
• Pumps must be accessible at all times for operation and maintenance.
Access should never be impeded or blocked.
About this pump / Safety
®
Metering Pumps and Hydraulic Accessories"
®
Motor-Driven
Page 9