Strobe Mode - Elation ELED DW PAR56 User Instructions

ELED DW PAR56
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE
button until DS-1 is displayed, press the UP button to display DS-2.
Now the display will disappear after 10s. Press any button for at least
10s to turn the display on again. Be advised though that the display
will turn off automatically after 10 seconds.
To set the display press the MODE button until DS-X is displayed.
The display will now stay on at all times.
DS-1= LCD display on at all times.
DS-2= LCD display shuts off after 10 seconds.
Master-Slave Operation:
This function will allows you to link units together to run in a Master-
Slave mode. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units built-in programs.
Any unit can act as a Master or as a Slave however, only one unit can be
programmed to act as the "Master."
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR microphone cables to link your units together.
Remember that the Male XLR connector is the input and the Female
XLR connector is the ouput. The first unit in the chain (master) will
use the female XLR connector only. The last unit in the chain will use
the male XLR connector only.
2. Set the "Master" unit to your desired mode or operation.
3. For the "Slave" unit(s), set the display to DMX mode 3, or 3 Channel
mode. The display should read "3000" or any variables, i.e "3001",
"3002 etc..
4. Connect the "Slave" unit or units and they will automatically start to
follow the "Master."
Sound Active Mode:
In this mode the ELED DW PAR56 will react to sound.
1. Plug the fixture in and press the MODE button until "3-So" is dis-
played.
2. The fixture will now change via sound.
Manual CW (Cool White) Adjust:
In this mode you are able to adjust the cool white color to your
Elation Lighting - www.elationlighting.com - ELED DW PAR56 Instruction Manual Page 7
© ®
Operating Instructions ELED DW PAR56
desired temperature.
1. Plug the fixture in and press the MODE button until "4-XX" is dis-
played.
2. Adjust the cool white color by pressing the UP and DOWN buttons.
Manual WW (Warm White) Adjust:
In this mode you are able to adjust the warm white color to your de-
sired temperature.
1. Plug the fixture in and press the MODE button until "5-XX" is dis-
played.
2. Adjust the warm white color by pressing the UP and DOWN buttons.
White Preset Mode:
In this mode you can select one of the already preset white color tem-
peratures. Please see the next page for preset color temperatures.
1. Press the MODE button until "6-XX" is displayed.
2. Press either the UP or DOWN buttons to choose your desired pre-
set white color temperature.

Strobe Mode:

Activate strobing and adjust the strobe rate.
1. Press the MODE button until "7-XX" is displayed.
2. Adjust the strobe speed by pressing either the UP or DOWN but-
tons. The speed can be adjusted from "7-01" the slowest, to "7-20"
the fastest.
Pulse Mode:
Activate pulsing and adjust the pulse rate.
1. Press the MODE button until "8-XX" is displayed.
2. Adjust the pulse speed by pressing either the UP or DOWN but-
tons. The speed can be adjusted from "8-01" the slowest, to "7-16"
the fastest.
DMX Mode:
Operating through a DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. This function
also allows you to use your fixtures as spot lights. The ELED DW PAR56
has 2 DMX modes: 3 Channel mode & 4 Channel mode. See pages
10-11 for each modes' DMX traits.
1. This function will allow you to control each individual fixture's traits
Elation Lighting - www.elationlighting.com - ELED DW PAR56 Instruction Manual Page 8
© ®
Operating Instructions