Kenmore 415.16649010 Use & Care Manual page 8

Main Burner Ignitor Lighting
Do not lean over grill while lighting.
1. Turn OFF all Gas Burner Control Valves.
2. Turn ON gas at LP cylinder.
3. Open main burner lid during Lighting.
4. To ignite any main burner, push in and turn the burner control
knob to the position. You will hear a clicking sound as the
burner is being ignited.
5. Once burner has ignited, turn knob to desired setting.
6. If Ignition does not occur in 5 seconds, turn the burner control
to OFF, wait 5 minutes for gas to clear away
lighting procedure.
7. Repeat steps 4 through 6 for the remaining main burners.
Searing Sideburner Ignitor Lighting
Do not lean over grill while lighting.
1. Open sideburner lid during lighting. Turn on gas at LP
cylinder.
2. Push in and turn control knob to
sound as the burner is being ignited. Ignition should occur
within 5 seconds, but leave the knob in the
full 10 seconds to maintain ignition.
3. Once burner has ignited, turn knob to desired setting.
4. If ignition does NOT occur in 5 seconds, turn the burner
control OFF. Wait 5 minutes
the lighting procedure.
Rotisserie Burner Ignitor Lighting
Do not lean over grill while lighting.
1. Open main burner lid during lighting. Turn on gas at LP
cylinder.
2. Push in and turn control knob to
sound as the burner is being ignited. Ignition should occur
within 5 seconds, but leave the knob in the
full 10 seconds to maintain ignition.
3. Once burner has ignited, turn knob to desired setting.
4. If ignition does NOT occur in 5 seconds, turn the burner
control OFF. Wait 5 minutes
the lighting procedure.
WARNING
Turn controls and gas source or tank OFF when not
in use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
8 • 464224010
, and repeat the
. You will hear a clicking
position for a
for gas to clear away , and repeat
. You will hear a clicking
position for a
for gas to clear away , and repeat
Match-Lighting
Do not lean over grill while lighting.
Open lid. Turn on gas at LP cylinder.
Light Burners one at time.
Match Lighting the Main Burners
1. Place match into match holder (hanging from right cart side).
2. Strike the match and position lit match through match light
hole on right hand side of cart. Shown Figure A.
3. Position lit match next to burner. Shown Figure B.
4. Push in and turn far right control knob to
burner lights and stays lit.
5. If ignition does NOT occur in 5 seconds, turn the burner
control knob OFF, wait 5 minutes
repeat the lighting procedure.
6. Light other burners in sequence from right to left by pushing
knob in and turning to
Match Light
Hole
Figure A
Match lighting the Rotisserie Burner - Figure C
1. Place match in match holder. Strike the Match. Position lit
match close to the front center of the rotisserie burner.
2. Push in and turn rotisserie burner control knob to
3. If ignition does NOT occur in 5 seconds, turn the burner
control knob OFF, wait 5 minutes
repeat the lighting procedure.
Rotisserie Burner
Figure C
Match lighting the Searing Sideburner - Figure D
1. Place match in matchholder. Strike the Match. Position lit
match close to the Searing burner.
2. Push in and turn Searing burner
knob to position. Be sure
burner lights and stays lit.
3. If ignition does NOT occur in 5
seconds, turn the burner control
knob OFF, wait 5 minutes
to clear away , and repeat the
lighting procedure.
position. Be sure
for gas to clear away
position.
Match shown next to burner
tube (under heat tent)
Figure B
for gas to clear away
Match holder
for gas
Figure D
, and
.
, and