Page 1
Use and Care Guide Liquid Propane Gas Grill Sears Item No. 415.16644900 This Grill is for Outdoor Use Only Safety WARNING • Parts • Use and Care • Read and follow all Safety, Assembly, • Assembly • and Use and Care Instructions in this...
Grill Halogen Light LIGHT OPERATION INSTRUCTIONS 1. Make sure light switch on the control panel is in the “OFF” position. 2. Connect light plug to an extension cord, then put the extension cord plug into the outlet on the wall. 3.
Cleaning the Lens 1. Prior to cleaning, make sure the light switch is in the “OFF” position and the light plug is disconnected from the power supply. 2. Do not clean the glass lens when warm. Allow to cool before cleaning. Sudden change in temperature may cause cracking of the glass lens.
Page 16
ASSEMBLY Attach the two locking casters at the rear of the bottom shelf and the two fixed casters at the front using the supplied wrench. Fixed caster Locking caster Bottom shelf Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers per panel. 7mm lock washer 1/4-20x1/2”...
Page 17
Attach light adapter to back panel using four #8-32x3/8” screws, 4mm lock washers, 4mm flat washers and #8 nuts, shown A. Place lower back panel between side panels at rear of bottom shelf. Secure lower back panel to side panels using two 1/4-20x1/2”...
Page 18
Insert front brace under control panel and between cart side panels. Secure using two 1/4-20x1½” screws, 7mm lock washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED AS ILLUSTRATED BELOW. 7mm Lock washer Qty.4 1/4-20x1½” screw Qty.4 7mm Lock 1/4-20x1½”...
Page 19
Attach left side lower fascia to left side upper fascia using three #10x3/8” screws, 5mm lock washers and 5mm flat washers, shown A. Remove the three screws and washers which were attached on left side of firebox front, shown B. Insert flange on left side shelf into side shelf brackets on side of firebox, shown C.
Page 20
On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 1/4-20x1½” screw and 7mm lock washer on each side. In upper holes, using one 1/4-20x1½” screw and 7mm lock washer on each side, shown A.
Page 21
Insert sideburner burner into left shelf. The stud on bottom of burner fits into rear small hole in sideburner drip pan on shelf, shown A. Secure burner to sideburner drip pan with one Wing nut, shown B. Make sure burner tube engages sideburner valve, shown C.
Page 23
Inside of cart, insert rear shield tabs into slots next to grease tray opening on upper back panel, shown A. Attach front shield tabs(with holes) under front brace with two #8x3/8” self-tapping screws, shown B. self-tapping screw #8x3/8” Qty.2 Note: some parts omitted front tab rear tab for clarity of illustration...
Page 24
Insert hinge pin on bottom of doors into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. PRESS Top of door Right door Hinge pin on bottom of door Left door...
Page 25
Install heat diffusers by sliding one end of each heat diffuser into slots at front of firebox and resting opposite end on pins in back of firebox. Note: Some parts omitted for clarity of illustration Front of firebox Heat diffuser Back of firebox Place cooking grates onto the firebox as shown.
Page 26
LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill.