TO REMOVE WHEELS (See Fig. 23)
Remove the klik pin and remove wheel from axle.
IMPORTANT: When installing wheel, be sure to use the
axle hole closest to the end of the shaft – do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
hole in wheel hub are not used for your model snow thrower.
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY)
Immediately prepare your snow thrower for storage at the
end of the season or if the unit will not be used for 30 days
WARNING: Never store the snow
thrower with gaso line in the tank in side
a build ing where fumes may reach an
open ﬂ ame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gas ap pliance. Allow the engine to cool
before storing in any enclosure.
When snow thrower is to be stored for a period of time,
clean it thor oughly, re move all dirt, grease, leaves, etc.
Store in a clean, dry area.
1. Clean entire snow thrower (See "CLEANING" in the
Maintenance section of this manual).
2. Inspect and replace belts, if necessary (See "TO RE-
PLACE BELTS" in the Service and Adjustments sec tion
of this manual).
3. Lubricate as shown in the Main tenance sec tion of this
4. Be sure that all nuts, bolts, screws, and pins are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if nec essary.
5. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
See engine manual.
FUEL SYS TEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuel hose, or tank during storage. Also, alcohol blended fuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
NOTE: To seal punctures or prevent ﬂ at tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and cor rosion.
See engine manual.
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower to
a qualiﬁ ed service center.
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualiﬁ ed service center,
which has proper equipment and experience to make any
necessary ad justments.
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and car buretor are empty.
Never use engine or carburetor cleaner prod ucts in the
fuel tank or permanent damage may occur.
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during stor age.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 min utes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
Drain oil (with engine warm) and replace with clean en-
gine oil. (See "ENGINE" in the Maintenance section of
this man ual).
1. Remove spark plug.
2. Pour one ounce (29 ml) of oil through spark plug hole
3. Pull recoil starter handle slowly a few times to dis tribute
4. Replace with new spark plug.
Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
Cover your snow thrower with a suitable pro tective cover
that does not retain moisture. Do not use plastic. Plastic
cannot breathe, which allows con densation to form and
will cause your snow thrower to rust.
IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm.