Door Handle; Housing Dimensions - Prima LPR808 Users Manual And Installation Handbook

Step 1: Prepare installation
Do not lift the appliance by the step 1: Prepare installation
Step 1: Prepare installation

door handle.

Do not lift the appliance by the door handle.
Do not lift the appliance by the
Whilst every care is taken to eliminate
Whilst every care is taken to eliminate
door handle.
burrs and raw edges from this product,
burrs and raw edges from this product,
Whilst every care is taken to eliminate
please take care when handling - we
please take care when handling - we
recommend the use of protective gloves
burrs and raw edges from this product,
recommend the use of protective
during installation.
please take care when handling - we
gloves during installation.
recommend the use of protective
Please note that the weight of this
Please note that the weight of this
appliance is approximately 31kg
gloves during installation.
(unpacked). Take care when lifting it
appliance is approximately 31kg
Please note that the weight of this
into the housing unit - always use an
(unpacked). Take care when lifting it
appropriate method of lifting.
appliance is approximately 31kg
into the housing unit - always use an
(unpacked). Take care when lifting it
Remove the fixing screws from the
appropriate method of lifting.
into the housing unit - always use an polythene bag on the top of the appliance,
but leave the appliance in the base tray
Remove the fixing screws from the
appropriate method of lifting.
packaging until you are ready to install it.
polythene bag on the top of the
Remove the fixing screws from the
appliance, but leave the appliance in
If this appliance is to be installed near to
polythene bag on the top of the
a corner where the adjacent cabinets run
the base tray packaging until you are
appliance, but leave the appliance in
at right angles forward of the appliance,
ready to install it.
there must be a gap of at least 90 mm
the base tray packaging until you are
If this appliance is to be installed near
between the appliance and the cabinets,
ready to install it.
to a corner where the adjacent
to prevent overheating of the cabinets.
If this appliance is to be installed near
cabinets run at right angles forward of
to a corner where the adjacent
the appliance, there must be a gap of
cabinets run at right angles forward of
at least 90 mm between the appliance
the appliance, there must be a gap of
and the cabinets, to prevent overheating
at least 90 mm between the appliance
of the cabinets.
and the cabinets, to prevent overheating
of the cabinets.
585
mm
585
mm
595mm
595mm
Installation Instructions
installation instructions - 60cm
Installation Instructions
547mm
547mm
20mm
20mm
588
mm
588
mm
550mm
550mm
23

Housing dimensions

The appliance is designed to fit into a
Housing dimensions
Housing dimensions
standard 600mm wide housing unit
The appliance is designed to fit into a
The appliance is designed to fit into a
with minimum internal dimensions as
standard 600mm wide housing unit with
standard 600mm wide housing unit
minimum internal dimensions as shown.
shown.
with minimum internal dimensions as
591mm is to the underside of the worktop
591mm is to the underside of the
shown.
when the appliance is built under, or to the
worktop when the appliance is built
underside of the panel above, when the
591mm is to the underside of the
under, or to the underside of the panel
appliance is installed into a tall housing
worktop when the appliance is built
above, when the appliance is installed
unit.
under, or to the underside of the panel
into a tall housing unit.
above, when the appliance is installed
into a tall housing unit.
min
560mm
min
560mm
min 550mm
min 550mm
30 - 80mm
30 - 80mm
568
mm
568
mm
12mm
gap in plinth
12mm
gap in plinth
23
90mm (minimum)
90mm (minimum)
min
590
mm
min
590
min
mm
580
mm
min
580
mm
6mm
6mm