Vision Fitness R2050 Assembly Manual page 3

A s s e m b l y
G u i d e
R2050
STEP-THRU SEMI-RECUMBENT FITNESS BIKE
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before
proceeding, find your new Fitness Bike's serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner's Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348
NOTE:
It is recommended that you apply grease to the threads of each bolt and screw as you assemble
your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts
and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.
ORANGE BAG
1
STEP
Rear Foot
• Slide the Rear Foot into place on the
back end of the frame. Secure the foot
in place to the frame with two bolts
(M8x20L) and two lock washers (SW8)
to the outside holes and with two bolts
(M8x65L) and two lock washers (SW8)
to the inside holes. Tighten with the
5mm T-Handle Wrench
BLUE BAG
2
STEP
• Rotate the handle on the seat frame to
the forward most position. Tighten the
adjustment bolt on the seat frame
bracket with the 5mm T-Shaped wrench.
• Slide the seat frame onto the seat rail.
• Attach the seat rail stopper onto the
seat rail with two (M8x20L) bolts and
two lock washers (SW8). Tighten with
the 5mm T-handle wrench. NOTE: The
seat rail stopper and bolts are in a
separate bag.
• Connect the heart rate wires in the
seat handlebar to the heart rate wires
coming up from the seat frame.
• Mount the seat handlebars to the seat
frame with four bolts (M8x15L) and four
lock washers (SW8). Tighten with the
Adjustment Bolt
5mm T-Handle wrench.
• Mount the seat bottom cushion to the
seat frame with four bolts (M6x35L) and
four arc washers (M6). Tighten with the
4mm L-shaped wrench.
• Mount the seatback cushion to the
seat frame with four bolts (M6x35L) and
four arc washers (M6). Tighten with the
4mm L-shaped wrench.
Rear Foot
Joint Cover
1
STEP
Seat Frame
Seat Rail
Stopper
4
STEP
2
STEP
3
STEP
Console Mast
Cover
Console Mast
Bracket
Console Mast
Water Bottle
Cage
SIMPLE
DELUXE
PREMIER
CONSOLES
3 PINK BAG
STEP
• Slide the console mast cover onto
the console mast.
• Take the wire tie that exits the
bottom of the console mast and wrap
it around the wire harness and heart
rate wires that are sitting in the
console mast bracket on the frame.
Pull the wire tie up through the top of
the console mast so that the wire
harness and heart rate wires exit the
top of the mast.
• Slide the bottom of the console mast
over the frame bracket being careful
not to pinch the heart rate wires or
wire harness. Assure the mast is
positioned correctly by inserting the
Set Screw (M8x10L) through the front
edge of the mast. Tighten with the
5mm T-handle wrench. Secure the
mast to the frame with four bolts
(M8x15L) and four lock washers (SW8).
Tighten with the 5mm T-handle wrench.
• Slide the console mast cover down
so it sits on the frame covers.
• Mount the console mast handlebar
to the console mast with two bolts
(M8x20L) and two lock washers (SW8).
Tighten with the 5mm T-handle wrench.
• With the screwdriver remove the
four bolts on the back side of the
console. Plug in the wire harness and
heart rate wires to the back side of the
console. Mount the console to the
console mast with the four bolts and
screwdriver.
• Remove the water bottle cage bolts
from the backside of the console mast.
Mount the water bottle cage to the
mast with these two bolts and the
screwdriver.
PEDALS
4
STEP
• Attach the left and right pedals to
the left and right crank arms. NOTE:
both pedals and crank arms should
be labeled left or right. Tighten with
the included pedal wrench.
• Plug in the power supply to the power
socket on the front side of the bike.
CONSOLE
5
STEP
• Refer to Product Selection and
Model Configuration decal on
console or follow these steps.
• Once the product is plugged in turn
on the console
• Select product (Bike (BK) or Elliptical
(EP)) using the resistance arrow keys.
Press ENTER to select.
• Select model number (Bike (1500,
2050, 2250, 3200) or Elliptical
(1500, 6000, 6200)) using the
RESISTANCE arrow keys. Press
ENTER to select. Console will reset to
start-up screen.
• The product selection and model
configuration is now complete.