Related Manuals for Network Electronics Flashlink ETH1000-D
Summary of Contents for Network Electronics Flashlink ETH1000-D
- Page 1 Flashlink User Manual ETH1000-D Gigabit Ethernet Media Converter with DWDM laser Rev. 1...
-
Page 2: Network-Electronics.com
ETH1000-D Rev. 1 Network Electronics AS P.O. Box 1020 N-3204 Sandefjord, Norway Phone: +47 33 48 99 99 Fax: +47 33 48 99 98 Email: support@network-electronics.com www.network-electronics.com Support Phone: +47 90 60 99 99 Revision history Current revision of this document is the uppermost in the table below. -
Page 3: Table Of Contents
5.1 Front panel – Status monitoring ..................10 5.2 GPI Alarm – Module status outputs..................11 6 Laser safety precautions..................12 General environmental requirements for Network Electronics equipment ....13 Product Warranty...................... 14 Appendix A Materials declaration and recycling information........15 A.1 Materials declaration......................15 A.2 Recycling information.......................15... -
Page 4: Eth1000-D Rev
Rev. 1 1 Product overview The Flashlink ETH1000-D is a 10/100/1000Base-T to 1000Base-X converter module. The module converts a 10/100/1000Mbps Ethernet signal on copper to 1000Mbps fibre suitable for long haul applications. The module has one electrical Ethernet port, and one fibre transceiver port (receiver fibre connector and transmit fibre connector). -
Page 5: Specifications
ETH1000-D Rev. 1 2 Specifications 2.1 Optical Characteristics Optical input Transmission circuit fibre: 9/125um Single Mode Sensitivity Better than –25dBm Optical wavelength 1200nm – 1610nm Detector damage threshold > +1dBm Max input power 0dBm Connector SC/UPC Optical Output Transmission circuit fibre... -
Page 6: Configuration
DIP switch 3 enables/disables 1000Base-T electrical connection. DIP switch 4 enables/disables auto-negotiation on the optical connection, 1000Base-X. When connecting ETH1000-D to ETH1000MC, auto-negotiation must be disabled. Using two ETH1000-Ds, these DIPs must be in the same situation. Dip 5, 6 and 7 are reserved. -
Page 7: Gyda-Sc Control
ETH1000-D Rev. 1 Dip 8 sets if GYDA-SC is able to configure or not. When GYDA-SC override is set, the actual setting can be read by using the info command (se GYDA-SC user manual for details). 3.2 GYDA-SC control Latest configuration from GYDA-SC is stored local on card. This prevents configuration loss during power recycling. -
Page 8: Connector Module
ETH1000-D Rev. 1 4 Connector module The ETH1000D has a dedicated connector module: ETH1000-C1. This module is mounted at the rear of the sub-rack. The module is shown in the figure below. OPT TX OPT RX 10/100/1000Base-T 4.1 Mounting the connector module The details of how the connector module is mounted, is found in the user manual for the sub- rack frame FR-2RU-10-2. -
Page 9: Terminal Format Support
ETH1000-D Rev. 1 4.2 Terminal format support The different input and output ports on ETH1000D can support a number of formats. The table below shows the input and output signals on the back plane. Terminal format support: Terminal Function Supported Format... -
Page 10: Module Status
ETH1000-D Rev. 1 5 Module status The status of the module can be monitored in three ways. 1. GYDA-SC System Controller (optional). 2. GPI at the rear of the sub-rack. 3. LED’s at the front of the sub-rack. Of these three, the GPI and the LED’s are mounted on the module itself, whereas the GYDA System Controller is a separate module giving detailed information on the card status. -
Page 11: Gpi Alarm - Module Status Outputs
ETH1000-D Rev. 1 5.2 GPI Alarm – Module status outputs These outputs can be used for wiring up alarms for third party control systems. The GPI outputs are open collector outputs, sinking to ground when an alarm is triggered. The GPI connector is shown in figure below. -
Page 12: Laser Safety Precautions
ETH1000-D Rev. 1 6 Laser safety precautions Guidelines to limit hazards from laser exposure. All the available EO units in the Flashlink range include a laser. Therefore this note on laser safety should be read thoroughly. The lasers emit light at 1310 nm or 1550 nm. This means that the human eye cannot see the beam, and the blink reflex cannot protect the eye. -
Page 13: General Environmental Requirements For Network Electronics Equipment
ETH1000-D Rev. 1 General environmental requirements for Network Electronics equipment The equipment will meet the guaranteed performance specification under the following environmental conditions: Operating room temperature range: 0°C to 40°C Operating relative humidity range: <90% (non-condensing) The equipment will operate without damage under the following environmental... -
Page 14: Product Warranty
Rev. 1 Product Warranty The warranty terms and conditions for the product(s) covered by this manual follow the General Sales Conditions by Network Electronics AS. These conditions are available on the company web site of Network Electronics AS: www.network-electronics.com network-electronics.com | 14... -
Page 15: Appendix A Materials Declaration And Recycling Information
Please contact Network Electronics’ Customer Support for assistance with recycling if this site does not show the information you require. Where it is not possible to return the product to Network Electronics or its agents for recycling, the following general information may be of assistance: −... -
Page 16: Ec Declaration Of Conformity
ETH1000-D Rev. 1 EC Declaration of Conformity MANUFACTURER Network Electronics AS P.B. 1020, N-3204 SANDEFJORD, Norway AUTHORISED REPRESENTATIVE Not applicable (Established within the EEA) MODEL NUMBER(S) ETH1000-D DESCRIPTION Gigabit Ethernet Media Converter with DWDM laser DIRECTIVES this equipment complies with...
Need help?
Do you have a question about the Flashlink ETH1000-D and is the answer not in the manual?
Questions and answers