Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Leggett & Platt Sleep Comfort
Summary of Contents for Leggett & Platt Sleep Comfort
-
Page 1: Owners Manual
99301076-b EDR12041 10/12 OWNERS MANUAL [ adjustable bases ]... -
Page 3: Table Of Contents
SC-MR2 Remote Control Programming ................ 14 Accessories ....................... 19 Turnbuckle Adjustment ....................20 Troubleshooting ......................21 Sleep Comfort™ Warranty ................... 22 If adjustable base does not operate or if parts are missing, call: 800-888-3078 Do not contact retail store or dealer. -
Page 4: Advisory
The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... - Page 5 In the event the technician is unable to perform service due to lack of accessibility, the service call will LOCkING CASTER be billed to the purchaser and the service will DETAIL have to be rescheduled. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
-
Page 6: Acoustics
The massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... -
Page 7: Installation
• (1) Warranty Activation Card • (1) Adjustable Base Quick Setup Guide 4” LEG 7” LEG (4 pieces) PUSH-IN LOCkING (4 pieces) LEG CASTER SCREW-IN LOCkING (4 pieces) LEG CASTER (4 pieces) REMOTE CONTROL Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... - Page 8 TAPPED HOLE AT EACH CORNER FIGURE 1: Leg and caster installation. steP 4 Remove and extend out power cord from the protective packaging. POWER CORDS MUST NOT INTERFERE WITH ANY ADjUSTABLE BASE MECHANISMS. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
- Page 9 COMPARTMENT DOOR INSTALLATION: TABS PRESS COMPARTMENT DOOR AGAINST THE BATTERY ENDS, SLIDE DOOR UP AND IN TO ENGAGE THE DOOR TABS FIGURE 3: Power down box battery installation and battery compartment door reinstallation. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
- Page 10 Return base to the level position. steP 10 Install mattress retainer at the foot end of the base as follows: a. Locate grommeted holes at foot of base (FIGURE 4). FIGURE 4: Grommeted hole locations. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
- Page 11 (FIGURES 5 and 6). Press down until horizontal retainer section is flush against base. MATTRESS RETAINER FIGURE 5: Mattress retainer installation. FIGURE 6: Mattress retainer installed. steP 11 Install mattress on adjustable base. Typical adjustable base installation is now complete. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
-
Page 12: Sc-Mr2 Remote Control
REMOTE CONTROL REqUIRES FOUR (4) AAA SIzE BATTERIES. TO CONSERvE BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY BUTTON IS PRESSED FOR MORE THAN 50 SECONDS. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... -
Page 13: Receiver Unit Operation
The power down box is factory wired to the motor, but the box itself is mobile and can be placed anywhere under the adjustable base on the floor. Position the power down box near your remote control when programming for best results. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... -
Page 14: Sc-Mr2 Remote Control Programming
Continue to hold for 5 seconds and then release the buttons (FIGURE 8). One remote control is now programmed to operate one base. FIGURE 8 Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... - Page 15 OPERATE ONLY ONE (1) REMOTE CONTROL AT A TIME. OPERATING TWO (2) REMOTE CONTROLS AT THE SAME TIME WILL MOMENTARILY BLOCk BOTH RF SIGNALS AND PREvENT BOTH CONTROLS FROM FUNCTIONING. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
- Page 16 Continue to hold for 5 seconds and then release the buttons (FIGURE 8). HEAD MASSAGE ON/OFF steP 3 BUTTON Repeat Step 1 and Step 2 for base 2. One remote control is now programmed to operate two bases. FIGURE 8 Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
- Page 17 PoS 1 and head massage on/off buttons. The transmission indicator light will flash slowly FIGURE 8 and then flash rapidly to indicate programming mode. Continue to hold for 5 seconds and then release the buttons (FIGURE 8). Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
- Page 18 POS 1 BUTTON Step 4. steP 4 Locate the power down box for base 2 and press the learn button for 1 second and release (FIGURE 7). HEAD MASSAGE ON/OFF BUTTON FIGURE 8 Sleep Comfort™ Adjustable Base Owners Manual 99301076-b...
-
Page 19: Accessories
Swing-away hinges are designed for use with dual queen or dual king size bed bases. The swing-away hinge allows easy access between two mated bases for domestic cleaning (i.e. sweeping, changing sheets) by swinging the bases apart. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... -
Page 20: Turnbuckle Adjustment
FIGURE 3 jAM NUT - CARRIAGE FIGURE 5 END OF ASSEMBLY USE STRAIGHT-EDGE TO CHECk LEvELNESS ROTATE BODY OF TURNBUCkLE UNTIL BED BASE FLATTENS WHEN LEvEL, TIGHTEN ALL jAM NUTS FIGURE 4 FIGURE 6 Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... -
Page 21: Troubleshooting
• If base is installed over a bed frame, verify massage motors are not causing bed frame (or bed frame components) to vibrate. Sleep Comfort™ Adjustable Base Owners Manual 99301076-b... -
Page 22: Sleep Comfort™ Warranty
Sleep Comfort™ Adjustable Beds (SC) warrants for life the entire bed against defects in material or workmanship. warranty - Parts warranty - Miscellaneous This warranty does not include warranted If a part needs replacement, the purchaser must return the part to SC freight prepaid. - Page 24 [ adjustable bases ] assembLeD in usa nationwiDe customer service lpadjustablebases.com © 2012 Leggett & Platt Adjustable Bed Group, a division of Leggett & Platt, Incorporated...