Advertisement
Available languages
Available languages
Quick Links
DUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.
1
Verify contents; inspect for damage.
x6 - Legs for T/F/Q
x9 - Legs for K/CK
x1 - Remote Control
(Varies according to base
type. Image may not match
actual remote control.)
3A
Remove cotter pin and
clevis pin from hinge (one
on each side) and fold
adjustable base out flat.
4
Cut the zip-tie and remove the mattress retainer.
!
CAUTION
BE CAREFUL USING SHARP
INSTRUMENTS. INJURY IS
POSSIBLE IF TOOLS ARE NOT
USED PROPERLY.
Sleepy's Basic Adjustable Base Setup Guide
NOTE
BASE APPEARANCE MAY VARY DEPENDING
ON FEATURES OF THE PURCHASED PRODUCT.
WARNING
!
DO NOT DROP!
ADJUSTABLE BASE IS HEAVY.
READ ALL INSTRUCTIONS BEFORE USING.
x2 - Side Mattress Retainers
x1 - Power Supply
ALLOW FOR ENOUGH SPACE TO
UNFOLD BASE IN SETUP AREA.
TEAM
LIFT
x1 - Mattress Retainer
x1 - Warranty Sheet
x1 - Remote Guide
x1 - Setup Guide
3B
When base is flat, reinsert clevis pin
and cotter pin (one on each side).
NOTE
!
WARNING
PINCH POINT WARNING!
KEEP HANDS AND FINGERS
CLEAR WHEN UNFOLDING BASE.
Open the shipping carton. Carefully, lift adjustable base
2
out of shipping carton and place on clean surface.
Remove remote, leg box, and protective plastic.
Advertisement
Related Manuals for Leggett & Platt Sleepy's Basic
Summary of Contents for Leggett & Platt Sleepy's Basic
- Page 1 Sleepy’s Basic Adjustable Base Setup Guide NOTE NOTE ALLOW FOR ENOUGH SPACE TO BASE APPEARANCE MAY VARY DEPENDING UNFOLD BASE IN SETUP AREA. ON FEATURES OF THE PURCHASED PRODUCT. WARNING WARNING TEAM LIFT DO NOT DROP! PINCH POINT WARNING! KEEP HANDS AND FINGERS ADJUSTABLE BASE IS HEAVY.
- Page 2 Screw all legs into the threaded inserts. HAND TIGHTEN. FOOT NOTE FOOT Inner holes on head end of base are to be used for headboard HEAD bracket installation. HEAD TWIN, FULL, & QUEEN SIZES (6 LEGS) KING (9 LEGS) If unassembled, plug remote control cord and power supply cord Extend power cord out head end of base.
- Page 3 Guía de instalación de la base ajustable Basic de Sleepy’s NOTA NOTA LA APARIENCIA DE LA BASE PUEDE VARIAR DEJE ESPACIO SUFICIENTE SEGÚN LAS CARACTERÍSTICAS DEL PARA DESPLEGAR LA BASE EN PRODUCTO COMPRADO. EL ÁREA DE CONFIGURACIÓN. ADVERTENCIA ELEVACIÓN EN ADVERTENCIA EQUIPO ¡NO LA DEJE CAER!
- Page 4 Inserte todas las patas en los insertos roscados. APRIETE MANUALMENTE FIRMEMENTE. NOTA Los orificios internos en la cabecera de la base se deben utilizar para la instalación del CABECERA CABECERA soporte de cabecera. TAMAÑOS GEMELA, MATRIMONIAL KING (9 PATAS) Y QUEEN (6 PATAS) Extienda el cable de alimentación desde ISi no está...
- Page 5 Guide de montage de la base ajustable Basic de Sleepy’s REMARQUE REMARQUE L’APPARENCE DE LA BASE PEUT DIFFÉRER EN FONCTION PRÉVOYER SUFFISAMMENT D’ESPACE POUR POUVOIR DÉPLIER DES CARACTÉRISTIQUES DU PRODUIT ACHETÉ. LA BASE COMPLÈTEMENT DANS L’EMPLACEMENT DÉSIRÉ. AVERTISSEMENT SOULEVER AVERTISSEMENT À...
- Page 6 Visser toutes les pattes dans les inserts filetés. SERRER À LA MAIN. REMARQUE PIED PIED Les trous intérieurs sur la tête de la base serviront au montage TÊTE TÊTE du support de la tête. TAILLES JUMEAU, DOUBLE ET GRAND (6 PATTES) TRÈS GRAND (9 PATTES) Faire passer le cordon d’alimentation principal sous Si déconnectés, branchez le cordon de la télécommande et le...
Need help?
Do you have a question about the Sleepy's Basic and is the answer not in the manual?
Questions and answers
What is the size of the screw in the leg that screws into the base for the Sleepy's Basic Adjustable Base. I cannot find the part on the website. I called yesterday and was told that there was not a taller leg or no extensions. I asked if one of the other legs from another base would work and was told no because other legs from another base cannot screw into the Sleepy's Basic Adjustable Base. I am going to go try to find something from another manufacturer. The serial # of the base is 0776T01838025. Thank you for your assistance.
The size of the screw for the leg that attaches to the Leggett & Platt Sleepy's Basic Adjustable Base is not specified in the provided context.
This answer is automatically generated
@Mr. Anderson As the manufacturer, you are unable to locate this information?
@Terese LoPresti I was able to find the thread size. I am going to say that the customer service in this instance has not been great.