Dialogic IMG 1010 Quick Start Manual
Integrated media gateway
Hide thumbs
Also See for IMG 1010:
- Quick start manual (11 pages) ,
- Installation instructions manual (9 pages) ,
- Installation and setup manual (169 pages)
Related Manuals for Dialogic IMG 1010
Summary of Contents for Dialogic IMG 1010
- Page 1 ® Dialogic IMG 1010 Integrated Media Gateway IMG 1010 Quick Start Guide January 2012 64-1204-01 www.dialogic.com...
- Page 2 Dialogic does not provide any intellectual property licenses with the sale of Dialogic products other than a license to use such product in accordance with intellectual property owned or validly licensed by Dialogic and no such licenses are provided except pursuant to a signed agreement with Dialogic.
-
Page 3: Hardware Limited Warranty
Please refer to the following Dialogic web site for information on hardware warranty information, which applies unless different terms have been agreed to in a signed agreement between yourself and Dialogic Corporation or its subsidiaries. The listed hardware warranty periods and terms are subject to change without notice. For purchases not made directly from Dialogic, please contact your direct vendor in connection with warranty period and terms that they offer. -
Page 4: Table Of Contents
IMG 1010 Quick Start Guide Table of Contents Hardware Limited Warranty ................3 Overview ....................... 6 Shipping Information ..................6 Connecting Power ..................7 Connecting AC Power ..................7 Connecting DC Power ..................8 ... -
Page 5: Revision History
Please be aware that the following terminology and abbreviations are used throughout this document. Please also be sure to consult the legal notice for other important details. ® • When used herein, the term IMG 1010 refers to the Dialogic IMG 1010 Integrated Media Gateway product. ®... -
Page 6: Overview
Overview This IMG 1010 Quick Start Guide is an abbreviated guide which describes how power and network cabling are connected prior to configuring. From there, the guide describes installing system software and GCEMS software. Once procedure is completed, the IMG system will be ready to start the configuration process. -
Page 7: Connecting Power
IMG 1010 Quick Start Guide Connecting Power Connecting AC Power If the IMG 1010 purchased is powered by an AC voltage then the AC input power must conform to the specifications in the table below. Input Vin (voltage) 90 VAC rms... -
Page 8: Connecting Dc Power
IMG 1010 Quick Start Guide Connecting DC Power If the IMG 1010 is powered by DC voltage, the DC input power must conform to the specifications in the table below. Input Vin (voltage) -40 VAC -60 VDC 1.85 amps 2.75 amps... -
Page 9: Grounding (Dc Version Only)
IMG 1010 Quick Start Guide Grounding (DC Version Only) The DC version of the IMG 1010 should be connected to a true earth ground. To connect chassis to ground you will need the following equipment: • 10-12 AWG machine tool wire (MTW) (green/yellow). -
Page 10: Network Connections
IMG 1010 to the GCEMS server for the purpose of downloading software, managing services, and configuring the IMG 1010 using the ClientView GUI. Located on the rear of the IMG 1010 are the network interfaces. The first interface labeled CTRL 0 is a Fast Ethernet interface typically dedicated to the GCEMS server for network management functions. -
Page 11: Connecting Data 0 Interface
1. Connect the cables as shown in the figure below. The figure below displays the DATA 0 interface being connected to a public network. 2. The DATA 0 interface located on the rear of the IMG 1010 and is a Gigabit-Ethernet port dedicated to VoIP Bearer traffic (RTP) or SIP/H.323 signaling. Refer to the the topics under the IMG 1010-Installation and Setup Guide >... -
Page 12: Connecting Tdm Signaling And Bearer Ports
IMG 1010 Quick Start Guide Connecting TDM Signaling and Bearer Ports The Bearer spans (Interface Offsets) 0-27 are connected to a TDM network. Each bearer interface which represents one DS1 can have signaling and/or bearer DS0’s configured on them. The Signaling/Timing interfaces can be connected to the TDM network as well. These interfaces are typically used for SS7 or ISDN signaling but can be used for any TDM functionality as well. -
Page 13: Configure Pre-Loaded Gcems Server
IMG 1010 Quick Start Guide Configure Pre-loaded GCEMS server When purchasing an IMG 1010, the customer has the option of purchasing a server which is labeled the GCEMS server. This server has been pre-loaded with a version of Red Hat Enterprise Linux OS along with all the applications and services needed to start configuring the IMG 1010. -
Page 14: Create Symbolic Link To Load System Software
2. From the ftpBuilds run the lnimg (link img) script [root@localhost]# ./lnimg 3. Follow the instructions and enter the appropriate IMG 1010 Build Number from the Available IMG 1010 Build files. Use the format described in the lnimg script. (1051=10.5.1, 1052=10.5.2, 1053=10.5.3). -
Page 15: Create Dhcpd.conf File
IMG 3. The following is the response after all prompts are complete: dhcpd.conf created with 1 IMG's configured... 4. The file will be created in the /opt/dialogic/common/osconfig directory. 5. Move the file to the /etc directory mv dhcpd.conf /etc) -
Page 16: Start The Services Nfs, Vsftpd, And Dhcpd, Services
#/sbin/chkconfig ntpd --list (Verify that runlevels 3,4 and 5 are all on.) 5. Once these services are running and the IMG software build is available the software can be downloaded. Refer to the IMG 1010 - Software Installation and Setup > IMG 1010-Downloading System Software topic in the online documentation download the system software from the GCEMS server to the IMG 1010. -
Page 17: Install Gcems Software
5. At the end of the installation you will be prompted to log out. Log out as root user by entering the exit command. For more information on installing GCEMS and ClientView, refer to the IMG 1010 - Software Installation and Setup > Installing GCEMS software topic in the online documentation... -
Page 18: Starting Clientview To Start Configuring Switch
IMG 1010 Quick Start Guide Starting ClientView to start Configuring Switch Once the IMG 1010 has the system software installed, the cabling is connected, and the GCEMS server has been configured, the ClientView application needs to be started. Once started, the clientView application can be used to configure the system. Follow procedure below to start ClientView.
Need help?
Do you have a question about the IMG 1010 and is the answer not in the manual?
Questions and answers