What To Do; If You Cannot Operate With The Remote Control; Freeze Damage Prevention - Toto WASHLET S350e Instruction Manual

What to Do?

If you cannot operate with the remote control

■
Operation is also possible using the buttons on
the Washlet control panel.
● The batteries may have worn out. Replace the batteries.
■
Replacing the batteries
Press on the Washlet control panel.
1
 
The POWER LED goes off.
Remove the remote control from the hanger.
2
(Page 16)
Open the cover and replace the AA batteries.
3
(Page 16)
Mount the remote control in the hanger.
4
Press on the Washlet control panel.
5
 
The POWER LED lights up.
■
About the batteries
●
Use dry cell, alkaline batteries. Follow the instructions below to prevent the batteries from rupturing or leaking fluid.

When replacing the batteries, use new batteries of the same brand.

If you will not be using the remote control for a long time, remove the batteries.

Do not use rechargeable batteries.
50
Washlet control panel
This button cannot be
used.
POWER LED

Freeze Damage Prevention

In preparation for freezing conditions, such as in wintertime, take measures to prevent freezing.
Attention!
●
Do not use the energy-saver feature if there is a risk of the product being exposed to freezing temperatures.
(The product may be damaged.)
●
Warm the bathroom so that the temperature around the product is not below freezing or take other appropriate
measures against freezing temperatures.
●
Before starting work, set "AUTO OPEN/CLOSE" (S350e, TCF4731A, TCF4732A only) (Page 40) to "OFF".
Close the water supply valve.
1
 
The water supply stops.
Water supply valve
CAUTION
Do not remove the water filter
drain valve while the water supply
valve is open.
(Otherwise, water may leak out.)
Drain the water from the toilet tank.
2
Turn the flush handle
of the toilet tank to
the full flush side.
Release the pressure from the
3
water supply pipe.
1. Remove the remote control from the
hanger, and press [MENU] on the rear
(Page 16)
side.
2. Use to select "CLEANING" and then
press [ENTER].
3. Use to select "WAND CLEANING
MODE ON/OFF", then press [ENTER].
The wand extends and water comes out.
4. In the [WAND CLEANING MODE ON/OFF]
screen, press [ENTER] again.
The wand retracts.
5. Remove the cover.
Cover
6. Remove the water filter drain valve.
Water filter drain valve
Water collector
7. Drain the water from the water supply hose.
Water supply hose
Position horizontally
8. After draining the water, mount the water
filter drain valve.
 
Tighten it securely using a flat-head screwdriver.
Water filter drain valve
9. Mount the cover.
Check that the POWER LED on
4
the Washlet main display has lit up.
(Page 17)
Set the toilet seat temperature
5
to "High".
(Page 26)
(To maintain the temperature, close the toilet seat
and toilet lid after finishing work.)
■
When you use Washlet again, the water supply
and power supply will be required. (See below)
Resupplying the Water
(After draining)
Open the water supply valve to
1
supply water.
 
Check that there are no leaks in the
plumbing or the Washlet.
[USA]
2
Insert the power plug.
[Asia, Oceania]
Switch the breaker on the
distribution board to ON.
Discharge water from the wand.
3
1. While pressing the left side of the toilet
seat,
2. Press the "REAR" button on the remote
control to discharge water from the
wand. (Catch the water in a paper cup
or other recipient.)
■
If the remaining water has frozen and
no water comes out
 
Heat the inside of the bathroom, and warm the
water supply hose and water supply valve using a
cloth soaked in warm water.
51