What To Do; If You Cannot Operate With The Remote Control; Freeze Damage Prevention - Toto WASHLET TCF6532G Instruction Manual

What to Do?

If you cannot operate with the remote control

The batteries may have worn out.
Replace the batteries.
■ Replacing the batteries
1
Unplug the power plug.
Switch the breaker on the distribution board to OFF.
(Electrical box type, Concealed power connection type)
 The POWER LED goes off.
Remove the remote control from the hanger.
2
(Page14)
Open the battery cover and replace the
3
AA batteries.
(Page14)
Mount the remote control in the hanger.
4
Insert the power plug.
5
Switch the breaker on the distribution board
to ON.
(Electrical box type, Concealed power connection type)
 The POWER LED lights up.

Freeze Damage Prevention

When the ambient temperature is likely to drop to 0°C or lower, take measures to prevent
freezing.
Attention!
●When the ambient temperature is likely to drop to 0°C or lower, do not use the energy saver feature.
(May damage the product.)
● Warm the bathroom or take measures against freezing so that the ambient temperature does not drop below 0°C.
Freeze damage prevention
■ How to drain the water
Close the shutoff valve.
1
 
The water supply stops.
38
Lit
CAUTION
Do not remove the water fi lter drain
valve while the shutoff valve is open.
(Otherwise, water may leak out)
Freeze damage prevention
Drain the pipe.
2
(1) Extend the wand.
  Operate with the buttons on the back
side of the remote control.
1. Press [MENU].
2. Use to select "CLEANING".
Press [ENTER].
3. Use to select "WAND
CLEANING MODE ON/OFF".
Press [ENTER] to extend the wand
and then press [ENTER] again
to retract the wand. (Release the
pressure from the water supply pipe.)
  Water comes out from around the wand.
(2) Unplug the power plug.
Switch the breaker on the distribution
board to OFF. (Electrical box type,
Concealed power connection type)
(3) Remove the cover and water fi lter drain valve.
Water fi lter drain
valve
Cover
Flat-head screwdriver
Resupplying the Water
Open the shutoff valve.
1
• Check that water is not leaking from a pipe or the main unit.
If the power is not turned ON
2
Insert the power plug.
Switch the breaker on the distribution board to ON.
(Electrical box type, Concealed power connection type)
Discharge water from the wand.
3
(1) Pressing down the right side of the toilet seat,
(2) Press [REAR] on the remote control to discharge water from the wand for about two minutes.
(It takes about one minute maximum before water comes out. Catch the water in a paper cup or other receptacle.)
■ If the remaining water has frozen and no water comes out
• Heat the inside of the bathroom, and warm the water supply hose and shutoff valve using a cloth soaked in warm water.
(continued)
(4) Drain the water from the water supply hose.
(Expect Concealed power connection type)
Water supply hose
Horizontally
(5) After draining the water, install the
water fi lter drain valve and cover.
  Insert the water fi lter drain valve and use a
fl at-head screwdriver to tighten it securely.
(6) Insert the power plug.
Switch the breaker on the distribution
board to ON. (Electrical box type,
Concealed power connection type)
Check that the POWER LED on
3
the main display is lit up.
(Page 15)
Set the water and toilet seat
4
temperature to "High".
(Page 22)
(To maintain the temperature.)
 
When fi nished, close the toilet seat and toilet lid.
■ To use the Washlet again
  The water needs to be resupplied. (See below)
(After draining)
Paper cup
Soft cloth soaked in water
(to prevent scratching)
39