Microcontroller Features - Hansol 520f User Manual

*1¿ 97.3.29 10:26 AM ˘ ` 12
Preset Mode Table
The timing shown in the following table will be factory preset for display.
Horizontal Pi x el 640 720 640 640 640 640
Frequency KH 31.469 31.469 31.469 37.500 37.861 35.000 35.156
2
µs
Period(T1) 31.778 31.778 31.778 26.667 26.413 28.571 28.444
Sync Wi d t h ( T 2) µs 2.542 3.813 3.813 2.032 1.270 2.116 2.000
µs
Back Por c h( T 3) 3.178 1.907 1.907 3.810 3.810 3.175 3.555
Active(T4) µs 25.422 25.422 25.422 20.317 20.317 21.164 22.222
µs
Fr o nt Por c h( T 5) 0.635 0.636 0.636 0.508 0.762 2.116 0.667
Vertical Li n e 350 400 480 480 480 480
Frequency H 70.087 70.087 59.940 75.000 72.809 66.667 56.250
2
Period(T1) ms 14.268 14.268 16.683 13.333 13.735 15.000 17.778
ms
Sync Wi d t h ( T 2) 0.095 0.064 0.064 0.080 0.079 0.086 0.057
Back Por c h( T 3) ms 1.905 1.080 1.048 0.427 0.528 1.110 0.626
Active(T4) ms 11.136 12.711 15.253 12.800 12.678 13.714 17.067
ms
Fr o nt Por c h( T 5) 1.145 0.413 0.318 0.027 0.238 0.086 0.028
I n t e r l a ced Y/N N N N N N N
H P N - - - -
Sync Pol a r i t y
V N P - - - -
12

Microcontroller features

800 800 800 800 1024 1024 1024 1024
37.879 46.875 48.077 48.363 56.476 60.023 57.928
26.400 21.333 20.800 20.677 17.707 16.660 17.247
Display modes memory
3.200 1.616 2.400 2.092 1.813 1.219 1.662
2.200 3.232 1.280 2.462 1.920 2.235 2.078
20.000 16.162 16.000 15.754 13.653 13.003 13.299
1.000 0.323 1.120 0.369 0.320 0.203 0.208
User setting area
600 600 600 600 768 768 768 768
60.317 75.000 72.188 60.004 70.069 75.029 72.117
16.579 13.333 13.853 16.666 14.272 13.328 13.866
0.106 0.064 0.125 0.124 0.106 0.050 0.121
0.607 0.448 0.478 0.600 0.513 0.466 0.448
15.840 12.800 12.480 15.880 13.599 12.795 13.246
0.026 0.021 0.021 0.062 0.053 0.017 0.086
N N N N N N N N
- - - - - - - - Factory presetting area
- - - - - - - -
Automatic save
The microcontroller automatically detects the video board installed in your
system. When you turn on the monitor, the Micro controller first checks the
display mode memory stored in the user setting area and the factory presetting
area.
The microcontroller has memory capacity to store 24 different display modes
including timing formats and display settings. This memory capacity is
divided into two parts. One is the user setting area, the other is the factory
presetting area.
The user can add nonstandard modes. If you adjust display Image, the image
is saved automatically. Then the microcontroller always detects and displays
the last mode stored in the user setting area when the monitor is turned on.
The user setting area maintains the last 6 display modes set by the user in its
memory. When the user setting area is full(6 modes are registered), if new
nonstandard timing is registered, the oldest timing settings will be deleted.
There are 14 display modes stored in this area. These display modes are preset
at the factory and include most of the display modes currently available(see
Timing Chart of this manual).
You can also retrieve the factory preset mode by selecting the RECALL menu.
The monitor automatically saves the setting value after certain times
(20 sec) of adjusting OSD menu.
13