Related Manuals for Hansol B15BF
Summary of Contents for Hansol B15BF
-
Page 1: Table Of Contents
Table of Contents Parts Connection to Computer How to Adjust Monitor Angle Installing Monitor Driver Name and Function of Front Power Management Feature Adjusting OSD Standard Signal Table Specification Troubleshooting Warning... - Page 2 INFORMATION TO USER: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-
Page 3: Parts
Good Posture Guide Parts Place the monitor to face the user and then adjust the monitor angle. Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cm Look down the monitor below the horizon. -
Page 4: Connection To Computer
Connection to Computer How to Adjust Monitor Angle Basic Connection How to Default Stand 12V DC connection Computer cable terminal For PC For Macintosh Use adapter. Adapter for Macintosh (Optional) Refer to the table on the rear side of the optional Macintosh adapter and adjust DIP switch by the resolution of the monitor. -
Page 5: Installing Monitor Driver
Installing Monitor Driver Run (Click) Install at Floppy driver and select the product model to set the optimum display in Window 95, 98 or 2000. Use the Driver Floppy provided. Click 'Next>'. Click 'Advanced..'. Click 'Monitor'. Automatic Installation 1. Insert the Diskette in the Floppy driver. 2. -
Page 6: Name And Function Of Front
Name and Function of Front Front panel Functions Power Switch Power switch is located in the lower center of the monitor stand. You can push the switch to turn on/off the power. Power Saving LED If the green LED around the power switch turns into blinking amber, it indicates the monitor is in power saving mode. -
Page 7: Power Management Feature
Power Management Feature Adjusting OSD When not in use for a long period of time, the monitor Brightness automatically reduces its power consumption, meeting power saving standards of EPA and NUTEK. The monitor is equipped with a power saving circuit that MENU SELECT conforms to the world-standard Display Power Manager Signalling... - Page 8 Color Vertical Position MENU SELECT MENU SELECT 1. Press the Menu button. 1. Press the Menu button. 2. Use to move Color ICON. 2. Use to move V-Position ICON. 3. Use SELECT button to select it. 3. Use SELECT button to select it. 4.
- Page 9 OSD Overlay Special SELECT MENU MENU SELECT 1. Use to move DOS Overlay ICON. 1. Press the Menu button. 2. Use SELECT button to select it. 2. Use to move SPECIAL ICON. 3. Use to adjust DOS Overlay. 3. Use SELECT button to select it. 4.
-
Page 10: Standard Signal Table
Standard Signal Table Auto-Config Horizontal Frequency Clock Frequency Vertical Frequency Resolution (KHz) (Hz) (MHz) MENU SELECT (720 X 400) 31.469 28.322 70.087 (640 X 480) 31.469 25.175 59.940 1. Press the Menu button. 2. Use to move the Auto-config ICON. (640 X 480) 37.500 75.000... -
Page 11: Specification
Specification Troubleshooting Model B15BF Power LED is off. Type Amorphous active matrix super TFT LCD Check the power connection. No picture. (Refer to page 4) Screen Size 38.1cm (Diagonal) Maximum Resolution 1024 X 768 @ 75 Hz Pixel Range 0.297 mm X 0.297 mm... -
Page 12: Warning
Warning To prevent damage or loss, please read this warning carefully. Adjust COLOR at User Mode in OSD Color Color is irregular. Menu. When connecting/disconnecting the plug, pull out the plug itself, and never pull the plug to prevent fire caused by short. - Page 13 M e m o...