Related Manuals for Hansol 700Fs
Summary of Contents for Hansol 700Fs
- Page 1 TFT-LCD Color Monitor Printed on the recyclable paper Printed in Korea www.hansolel.co.kr Part No. 942227020001-01...
-
Page 2: Table Of Contents
Table of Contents Parts Connection to Computer How to Adjust Monitor Angle Installing Monitor Driver Power Management Feature Name and Function of Front Adjusting OSD Installing VESA stand and USB Installing Option Stand Standard Signal Table Specification Troubleshooting Warning... -
Page 3: Parts
Good Posture Guide Parts Place the monitor to face the user and then adjust the monitor angle. Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. Look down the monitor about 50cm below the horizon. -
Page 4: Connection To Computer
Connection to Computer Applied Connection Basic Connection 1. Connect the adapter to "12V DC" input terminal. 12V DC connection Computer cable 2. Connect the computer cable to PC. terminal For PC 3. Connect audio output to Audio In (Stereo). 4. Connect headphone or earphone to H-Phone terminal. For Macintosh Use adapter. -
Page 5: How To Adjust Monitor Angle
How to Adjust Monitor Angle Installing Monitor Driver Run (Click) Install at Floppy driver and select the product model to set the How to Default Stand optimum display in Window 95, 98 or 2000. Use the Driver Floppy provided. Automatic Installation 1. -
Page 6: Power Management Feature
Power Management Feature When not in use for a long period of time, the monitor automatically reduces its power consumption, meeting power saving standards of EPA and NUTEK. The monitor is equipped with a power saving circuit that conforms to the world-standard Display Power Manager Signalling Click 'Next>'. -
Page 7: Name And Function Of Front
Name and Function of Front Front panel Functions Power Switch Power switch is located in the lower center of the monitor stand. You can push the switch to turn on/off the power. Power Saving LED If the green LED around the power switch turns into blinking amber, it indicates the monitor is in power saving mode. -
Page 8: Adjusting Osd
Adjusting OSD Brightness Vertical Position MENU MENU 1. Press the Menu button. 1. Press the Menu button. 2. Use to select the Brightness ICON. 2. Use to select the V-Position ICON. 3. Use to adjust display upward or downward. 3. Use to adjust the brightness. - Page 9 Color Special MENU MENU 1. Press the Menu button. 1. Press the Menu button. 2. Use to select the Color ICON. 2. Use to select the Special ICON. 3. Use into the submenu. 3. Use into the submenu. Video Level Preset Color MENU MENU...
- Page 10 OSD Overlay Auto-Config MENU MENU 1. Press the Menu button. 1. Use to select the OSD Overlay. 2. Use to select the Auto-Config. 2. Use to adjust OSD Overlay. 3. Use to readjust the display condition. 3. Press the Menu button to exit. In most cass, Auto-Config adjusts display appropriately.
-
Page 11: Sound Control
Treble Sound Control MENU MENU 1. Use to select the Treble. 1. Press the Menu button. 2. Use to adjust treble. 2. Use to select the Sound Control. 3. Press the Menu button to exit. 3. Use into the submenu. Volume Factory Init MENU... -
Page 12: Installing Vesa Stand And Usb
4. Locate the option stand on the 3. Disassemble the stand. supporter. Install USB in the designated location in the rear side of the stand. (Use dedicated USB from Hansol Electronics only.) 5. Tighten four screws. 6. Stand the monitor and spread out the stand bar. -
Page 13: Standard Signal Table
Standard Signal Table Specification Model 700Fs Horizontal Frequency Vertical Frequency Clock Frequency Resolution (KHz) (MHz) (Hz) Type Amorphous active matrix super TFT LCD 28.322 (720 X 400) 31.469 70.087 Screen Size 43.18cm (Diagonal) 25.175 (640 X 480) 31.469 59.940 Maximum Resolution 1280 X 1024@75 Hz 31.500... -
Page 14: Troubleshooting
Troubleshooting Adjust COLOR at User Mode in OSD Color Color is irregular. Menu. Power LED is off. Check the power connection. No picture. (Refer to page 4) Check the resolution and frequency of Double images or computer and video card, and set up a 'ghosts'. -
Page 15: Warning
Warning M e m o To prevent damage or loss, please read this warning carefully. When connecting/disconnecting the plug, pull out the plug itself, and never pull the plug to prevent fire caused by short. To prevent electric shock, do not connect/dis- connect the plug with wet hand.