Table of Contents
Advertisement
Quick Links
INFORMATION TO USER :
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates, uses and can
radiate radio frequency energy and,if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation; if this equipment does cause harmful interference to radio or
television reception, which can be determined by determined by turning the
equipment off and on, the user is encouraged to try to crrent the interference by
one or more of the fllowing measures:
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit difference
from that to which the recerver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment
ENERGY STAR
As an ENERGY STAR partner, Hansol Electronics Inc.
has determined that this product meets energy Star guidelines
for energy efficiency.
Table of Contents
3
4
5
6
8
10
11
18
19
20
22
Advertisement
Table of Contents
Related Manuals for Hansol H750D
Summary of Contents for Hansol H750D
-
Page 1: Table Of Contents
Changes or modifications not expressly approved by the Warning manufacturer responsible for compliance could void the user's authority to operate the equipment ENERGY STAR As an ENERGY STAR partner, Hansol Electronics Inc. has determined that this product meets energy Star guidelines for energy efficiency. -
Page 2: Parts
Good Posture Guide Parts Place the monitor to face the user and then adjust the monitor angle. Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. Look down the monitor below the horizon. -
Page 3: Connection To Signal Source
Connection to Signal Source The range of control Angle How to Adjust the Stand Basic Connection Port for AC power cable Port for Audio cable from audio source. Port for Head Phone or External Speaker Port for signal cable from DVI signal source. Kensington Lock Port for signal cable from analog signal source. -
Page 4: Installing Monitor Driver
Installing Monitor Driver Run (Click) "Install" at Floppy Diskette driver and select the model name to set the optimum display in Window 95, 98 or 2000, XP. Use the Driver provided. Click 'Monitor'. Click 'Next>'. Click 'Advanced..'. Click 'Change..'. Automatic Installation 1. -
Page 5: Name And Function Of Front
Name and Function of Front Front panel Functions Power button Power button is located in the lower center of the Front Bezel. You can push the button to turn on/off the power. Power Indicating LED Dark : Power off Green : Normal mode Green blinking : DPMS mode or Check Signal Cable mode. -
Page 6: Power Management Feature
Power Management Feature Adjusting OSD The monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling Input Source (DPMS) mode of Video Electronics Standard Association (VESA). The power management feature requires that the video card of the computer should support DPMS function. - Page 7 Clock Phase Brightness &Contrast MENU SELECT MENU SELECT 1. Press the MENU button to access main menu. 2. Use to move Clock Phase ICON. 1. Press the MENU button to access main menu. 3. Press SELECT button into the submenu. 2.
- Page 8 Preset Color Clock Phase MENU 1. Use to select the 6500K, and 9300K. SELECT 2. Press the Menu button to return previous state. 1. Press to move Clock Phase ICON. 2. Use SELECT button to select it. 6500K : Reddish white 9300K : Bluish white 3.
- Page 9 Language OSD H-Position MENU SELECT SELECT 1. Use to move Language ICON. 1. Use to move OSD H-Position ICON. 2. Press SELECT button to select it. 2. Press SELECT button to select it. 3. Use to select language. 3. Use to adjust OSD left or right.
-
Page 10: Standard Signal Table
Sound (Option) Auto-Config SELECT or MENU VOL BUTTON 1. When change DVI display into Analog display select source button located in the left. 1. Use to move Sound ICON. Analog display will be showed after Analog input message. 2. Press SELECT button to select it. 3. -
Page 11: Specification
Pin assignment table D-Sub Specification Mini 15pin connector Model H750D (B17CF Type Amorphous active matrix super TFT LCD Screen Size 43.2cm (Diagonal) Maximum Resolution 1280 X 1024 @ 75 Hz Pin No. Assignment Pin No. Assignment Red Video 5V Input Pixel Range 0.264 mm X 0.264 mm... -
Page 12: Troubleshooting
Troubleshooting Power LED is dark. Check the power connection. Adjust COLOR at User Mode in OSD Color Color is irregular. No picture. (Refer to page 4) Menu. OSD, "check cable." Check the resolution and frequency of is displayed on the Check the computer power is on. -
Page 13: Warning
Warning To prevent damage or loss, please read this warning carefully. When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short. To prevent electric shock, do not connect/dis- connect the plug with wet hand. If you see smoke or smell something burning, stop using the unit, switch off the power, pull out the plug, and then contact your local service station.