D-Link DSR-250N User Manual page 213

Unified Services Router
0x%08x 0x%08x,
0x%08x 0x%08x 0x%08x 0x%08x,
sc_txq[%d] : , i
tid %p pause %d : , tid, tid->paused
%d: %p , j, tid->tx_buf[j]
%p , buf
axq_q:
%s: unable to reset hardware; hal status
%u, __func__, status
****ASSERTION HIT****
MacAddr=%s,
TxBufIdx=%d, i
Tid=%d, tidno
AthBuf=%p, tid->tx_buf[i]
%s: unable to reset hardware; hal status
%u,
%s: unable to reset hardware; hal status
%u,
%s: unable to start recv logic,
_fmt, __VA_ARGS__ \
sample_pri=%d is a multiple of
refpri=%d, sample_pri, refpri
===========ft-
>ft_numfilters=%u===========, ft-
>ft_numfilters
filter[%d] filterID = %d
rf_numpulses=%u; rf->rf_minpri=%u; rf-
>rf_maxpri=%u; rf->rf_threshold=%u; rf-
>rf_filterlen=%u; rf->rf_mindur=%u; rf-
>rf_maxdur=%u,j, rf->rf_pulseid,
NOL
WARNING!!! 10 minute CAC period as
channel is a weather radar channel
%s disable detects, __func__
%s enable detects, __func__
%s disable FFT val=0x%x , __func__,
val
%s enable FFT val=0x%x , __func__,
val
%s debug level now = 0x%x , __func__,
dfs_debug_level
RateTable:%d, maxvalidrate:%d,
ratemax:%d, pRc->rateTableSize,k,pRc-
>rateMaxPhy
%s: txRate value of 0x%x is bad.,
__FUNCTION__, txRate
Valid Rate Table:-
DEBUG ath_pci: 32-bit DMA not available
ath_pci: cannot reserve PCI memory
DEBUG region
ath_pci: cannot remap PCI memory
DEBUG region) ;
DEBUG ath_pci: no memory for device state
%s: unable to attach hardware: '%s'
DEBUG (HAL status %u),
DEBUG %s: HAL ABI mismatch;
DEBUG %s: failed to allocate descriptors: %d,
%s: unable to setup a beacon xmit
DEBUG queue!,
DEBUG %s: unable to setup CAB xmit queue!,
%s: unable to setup xmit queue for %s
DEBUG traffic!,
%s: unable to register device, dev-
DEBUG >name
DEBUG %s: autocreation of VAP failed: %d,
ath_dev_probe: no memory for device
DEBUG state
kdot11RogueAPEnable called with
DEBUG NULL argument.
kdot11RogueAPEnable: can not add
DEBUG more interfaces
kdot11RogueAPGetState called with
DEBUG NULL argument.
kdot11RogueAPDisable called with
DEBUG NULL argument.
%s: SKB does not exist.,
DEBUG __FUNCTION__
DEBUG %s: recvd invalid skb
DEBUG unable to register KIFDEV to UMI
The system is going to factory
DEBUG defaults........!!!
DEBUG %s, msg
DEBUG %02x, *(data + i)
DEBUG Inside crypt_open in driver ######
DEBUG Inside crypt_release in driver ######
Inside crypt_init module in driver
DEBUG @@@@@@@@
Inside crypt_cleanup module in driver
DEBUG @@@@@@@@
DEBUG SKB is null : %p ,skb
DEBUG DST is null : %p ,dst
211
User Manual
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL