Table of Contents
Advertisement
What's
Happening
When you press
the remote
control Mute or
Volume button,
nothing
happens.
Your PIP
(Picture-In-
Picture) button
isn't working.
L
W
IMITED
This Limited Warranty is a legal document. Keep it in a safe place.
Remember to keep your Sales Receipt for warranty service. We will
consider any items you return without a copy of the Proof of Purchase to
be out of warranty.
This warranty extends only to the original user ("you," "your") of the DISH Network
remote control and is limited to the purchase price of the remote control. EchoStar
Technologies Corporation and its affiliated companies ("we," "our," "us") warrant this
remote control against defects in materials or workmanship as follows.
For one year from the original date of purchase, if we find the remote control is defective
subject to the limits of this warranty, we will replace the remote at no charge for parts or
labor. We warrant any such work done against defects in materials or workmanship for the
remaining part of the original warranty period.
This warranty does not cover installation of the DISH Network System; consumer
instruction; physical set up or adjustment of any consumer electronic equipment; remote
control batteries; signal reception problems; loss of use of the equipment; unused
programming charges due to equipment malfunction; cosmetic damage; damage due to
lightning, electrical or telephone line surges, fire, flood, or other acts of Nature; accident;
misuse; abuse; repair or alteration by other than our factory service; negligence;
commercial or institutional use; improper or neglected maintenance; equipment sold AS IS
or WITH ALL FAULTS; equipment removal or reinstallation; shipping damage if the
equipment was not packed and shipped in the manner we prescribe; nor equipment
purchased, serviced, or operated outside the contiguous United States of America.
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE
REMEDY. WE SHALL NOT BE HELD LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED
WARRANTY ON THIS DEVICE, NOR FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGE RESULTING FROM THE USE OF, OR INABILITY TO
USE, THIS DEVICE. UNDER NO CIRCUMSTANCES SHALL OUR LIABILITY, IF
ANY, EXCEED THE PURCHASE PRICE PAID FOR THIS DEVICE. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS
DEVICE IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. WE
RESERVE THE RIGHT TO REFUSE TO HONOR THIS WARRANTY IF WE
DETERMINE ANY OF THE ABOVE EXCEPTIONS TO HAVE CAUSED THIS
DEVICE NOT TO HAVE PERFORMED PROPERLY. THIS WARRANTY SHALL BE
What's Wrong
• Maybe you have
not set up the
remote control.
• Maybe you're
trying to control
TV volume but
you set up the
remote to control a
tuner or amplifier
in AUX mode.
• Your receiver
doesn't use PIP.
ARRANTY
What You Can Do
• See Programming the Remote to
Control Your TV on page S-2 and
Programming for Other Equipment on
page 2.
• Set up the remote to control either
TV volume or tuner/amplifier volume,
whichever you want. See page 6.
• Upgrade to a receiver with this feature.
19
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Remote Control and is the answer not in the manual?
Questions and answers
How do I open door to system info
Power went out. Blue screen says to hold “OK” button for three seconds. My remote doesn’t have an “OK” button. What do I do?
How do I change the secondary remote channel (TV2) so both remotes are have the same channel. I have two remotes and want them both using the same tv from different rooms.
To change the secondary remote channel for a Dish Network remote so both remotes control the same TV, follow these steps:
1. Turn on the receiver and display the System Info screen (refer to the receiver user guide if needed).
2. Write down the remote address shown on the screen.
3. Press and hold the AUX button on the remote until all mode buttons light up, then release it. The AUX button should flash.
4. Press the "3" button on the number pad.
5. Enter the remote address you wrote down in step 2 using the number pad.
6. Press the POUND (#) button. The AUX button should blink three times.
7. Press the RECORD button to confirm that the remote is programmed to match the receiver.
Now both remotes should be set to the same address and control the same TV.
This answer is automatically generated
this does not look like my remote and how do I go fast forword ive ony been able to go 30 sec or 15 times
To fast forward using the Dish Network remote control, press and release the fast-forward button to skip forward through recorded programs. To fast-forward quickly (x4 speed), press and hold the button before releasing. If you press and release the button once while in fast-forward mode, the speed increases to x60.
This answer is automatically generated
how do you search using the new remote
You can search using the DISH Network remote control by using voice commands. With DISH Voice Remotes, simply say what you want, such as:
- "Tune to ESPN" to watch ESPN.
- "Free previews" to open the Free Preview Showcase menu.
- "Play," "Pause," or "Fast Forward" to control playback.
Make sure you are in SAT mode by pressing the SAT Mode button before using these features.
This answer is automatically generated
Where is the control menu button