Table of Contents
Advertisement
you will only be able to use the POWER and VCR function buttons.
The section Programming Using the Equipment Code Tables has a step
that tells the remote control to go into Limited Mode. Also, a quick
way to put the remote in Limited Mode is on page S-3.
Note: Limited Mode cannot be used with audio amplifiers.
P
ROGRAMMING
You can set up the remote to control other equipment using the
equipment codes listed on page 10 and the modes as shown on page 1.
Instructions
1
Turn the equipment on.
2
Find the brand name of the
equipment in the tables
starting on page 10.
3
Press and hold the mode
button until all the other
mode buttons light up, and
then let go of the button.
The mode button flashes.
4
For AUX mode only. Press
0 for a second TV, or 1 for a
second VCR, or 2 for a
tuner, or amplifier.
5
Enter one of the three-digit
equipment codes from the
table using the number
buttons.
6
If you want to program
Limited Mode, press 1.
If not, skip to step 7.
U
E
SING
QUIPMENT
C
ODE
Additional Information
Use the equipment's front panel
buttons or its remote control.
If the brand isn't listed, see
Scanning for Equipment Codes
on page 4.
For example, hold the TV mode
button for a TV until all of the
other mode buttons light. When
you let go, TV will flash.
This step is for programming
the kind of equipment that
should be programmed in AUX
mode. If you're not
programming in AUX mode,
skip to step 5.
The three-digit equipment code
should be for the brand name of
your equipment that you found
in step 2.
See Limited Mode on page 2 for
more information.
T
ABLES
3
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Remote Control and is the answer not in the manual?
Questions and answers
How do I open door to system info
Power went out. Blue screen says to hold “OK” button for three seconds. My remote doesn’t have an “OK” button. What do I do?
How do I change the secondary remote channel (TV2) so both remotes are have the same channel. I have two remotes and want them both using the same tv from different rooms.
To change the secondary remote channel for a Dish Network remote so both remotes control the same TV, follow these steps:
1. Turn on the receiver and display the System Info screen (refer to the receiver user guide if needed).
2. Write down the remote address shown on the screen.
3. Press and hold the AUX button on the remote until all mode buttons light up, then release it. The AUX button should flash.
4. Press the "3" button on the number pad.
5. Enter the remote address you wrote down in step 2 using the number pad.
6. Press the POUND (#) button. The AUX button should blink three times.
7. Press the RECORD button to confirm that the remote is programmed to match the receiver.
Now both remotes should be set to the same address and control the same TV.
This answer is automatically generated
this does not look like my remote and how do I go fast forword ive ony been able to go 30 sec or 15 times
To fast forward using the Dish Network remote control, press and release the fast-forward button to skip forward through recorded programs. To fast-forward quickly (x4 speed), press and hold the button before releasing. If you press and release the button once while in fast-forward mode, the speed increases to x60.
This answer is automatically generated
how do you search using the new remote
You can search using the DISH Network remote control by using voice commands. With DISH Voice Remotes, simply say what you want, such as:
- "Tune to ESPN" to watch ESPN.
- "Free previews" to open the Free Preview Showcase menu.
- "Play," "Pause," or "Fast Forward" to control playback.
Make sure you are in SAT mode by pressing the SAT Mode button before using these features.
This answer is automatically generated
Where is the control menu button