Do you have a question about the Remote Control and is the answer not in the manual?
Questions and answers
Jenny custer
January 17, 2025
How do I open door to system info
Jeffrey Marble
January 26, 2025
Power went out. Blue screen says to hold “OK” button for three seconds. My remote doesn’t have an “OK” button. What do I do?
Pete
February 27, 2025
How do I change the secondary remote channel (TV2) so both remotes are have the same channel. I have two remotes and want them both using the same tv from different rooms.
1 comments:
Mr. Anderson
February 27, 2025
To change the secondary remote channel for a Dish Network remote so both remotes control the same TV, follow these steps:
1. Turn on the receiver and display the System Info screen (refer to the receiver user guide if needed). 2. Write down the remote address shown on the screen. 3. Press and hold the AUX button on the remote until all mode buttons light up, then release it. The AUX button should flash. 4. Press the "3" button on the number pad. 5. Enter the remote address you wrote down in step 2 using the number pad. 6. Press the POUND (#) button. The AUX button should blink three times. 7. Press the RECORD button to confirm that the remote is programmed to match the receiver.
Now both remotes should be set to the same address and control the same TV.
This answer is automatically generated
Judy Roof
February 28, 2025
this does not look like my remote and how do I go fast forword ive ony been able to go 30 sec or 15 times
1 comments:
Mr. Anderson
February 28, 2025
To fast forward using the Dish Network remote control, press and release the fast-forward button to skip forward through recorded programs. To fast-forward quickly (x4 speed), press and hold the button before releasing. If you press and release the button once while in fast-forward mode, the speed increases to x60.
This answer is automatically generated
Gary Nelson
April 3, 2025
how do you search using the new remote
1 comments:
Mr. Anderson
April 3, 2025
You can search using the DISH Network remote control by using voice commands. With DISH Voice Remotes, simply say what you want, such as:
- "Tune to ESPN" to watch ESPN. - "Free previews" to open the Free Preview Showcase menu. - "Play," "Pause," or "Fast Forward" to control playback.
Make sure you are in SAT mode by pressing the SAT Mode button before using these features.
Need help?
Do you have a question about the Remote Control and is the answer not in the manual?
Questions and answers
How do I open door to system info
Power went out. Blue screen says to hold “OK” button for three seconds. My remote doesn’t have an “OK” button. What do I do?
How do I change the secondary remote channel (TV2) so both remotes are have the same channel. I have two remotes and want them both using the same tv from different rooms.
To change the secondary remote channel for a Dish Network remote so both remotes control the same TV, follow these steps:
1. Turn on the receiver and display the System Info screen (refer to the receiver user guide if needed).
2. Write down the remote address shown on the screen.
3. Press and hold the AUX button on the remote until all mode buttons light up, then release it. The AUX button should flash.
4. Press the "3" button on the number pad.
5. Enter the remote address you wrote down in step 2 using the number pad.
6. Press the POUND (#) button. The AUX button should blink three times.
7. Press the RECORD button to confirm that the remote is programmed to match the receiver.
Now both remotes should be set to the same address and control the same TV.
This answer is automatically generated
this does not look like my remote and how do I go fast forword ive ony been able to go 30 sec or 15 times
To fast forward using the Dish Network remote control, press and release the fast-forward button to skip forward through recorded programs. To fast-forward quickly (x4 speed), press and hold the button before releasing. If you press and release the button once while in fast-forward mode, the speed increases to x60.
This answer is automatically generated
how do you search using the new remote
You can search using the DISH Network remote control by using voice commands. With DISH Voice Remotes, simply say what you want, such as:
- "Tune to ESPN" to watch ESPN.
- "Free previews" to open the Free Preview Showcase menu.
- "Play," "Pause," or "Fast Forward" to control playback.
Make sure you are in SAT mode by pressing the SAT Mode button before using these features.
This answer is automatically generated
Where is the control menu button