Table of Contents Quick Setup Confirm Your Receiver Model ...S-1 Install Your Selected Key ...S-2 Insert the Batteries...S-2 Making the Remote Work with Your Receiver ...S-3 Program the Remote to Control Your TV ...S-4 Programming the Recover Button for TV2 Operation...S-5 Placing Your Remote in Limited Mode...S-6 Operation If You Lose Your Picture ...S-6...
Quick Setup Confirm Your Receiver Model If your receiver looks like Duo ViP 222 & DuoDVR™ ViP ® one of these... DuoDVR™ ViP DISH JVC IRR The remote functions as needed in regards to watching your If your satellite television and VCR. It does not rewind or fast forward while watching a recorded VCR tape.
Install Your Selected Key Note: If you are using the blue TV2 key that comes already installed in your remote, skip this step and proceed with the next step Separate the key Pull the by inserting your remote thumbnail or a coin battery cover off.
Making the Remote Work With Your Receiver If you installed one of these keys, continue with step If you installed a UHF key, make sure the UHF antenna is installed on the back of the receiver. Confirm that you see the System Information screen.
Program the Remote to Control Your TV Turn your TV on. Press POWER. Press POUND. The TV Mode button flashes three times. Quick Setup Press & hold the TV Mode button until all Mode buttons light up. Press the UP ARROW on the remote repeatedly (about 1 press per second) until your TV turns off.
Programming the Recover Button for TV2 Operation For TV2 Remote Controls on DuoDVR Duo ViP ® 222, DuoDVR and DuoDVR Programming your RECOVER button allows you to easily regain satellite programming if you accidentally change TV channels or inputs. Press & hold the TV Mode button until all Mode buttons light up.
Quick Setup/Operation Placing Your Remote in Limited Mode Limited Mode locks out all the TV mode operations except for TV power, Mute, and Volume. This prevents you from accidentally tuning away from satellite programming. Press & hold the TV Mode button until all Mode buttons light up.
Remote Operation To use the features described in this section, make sure you are in SAT mode by pressing the SAT Mode button. Note: Some features may not be available depending on your receiver model. Receiver Power & TV Power Top button turns the receiver on and off Bottom button turns...
(PIP) Buttons Display PIP features on some TVs with PIP capabilities Note: Remote operation is different on DISH Network TVs. See your DISH Network TV User's Guide for proper operation. Operation TV Mode Remote key may be different than what is shown here for instructions.
Remote Operation To use the features described in this section, make sure you are in VCR mode by pressing the VCR Mode button. You can use this mode to operate your DVD player instead of a VCR. Remote programming is required. See page 2 for instructions. VCR/DVD Power &...
EMOTE ONTROL VERVIEW Use this full-function remote to control a variety of DISH Network receivers. Also, you can program the remote to control most of the popular brands of audio/video equipment like a TV, VCR, DVD player, or a second DISH Network satellite receiver. See Programming for Other Equipment on page 2.
TVs, page S-8 (at the beginning of this guide). • VCRs and DVD players, page S-9. • DISH Network satellite receivers, page S-7. • Stereo equipment uses only these buttons: SELECT (to change inputs), MUTE, VOLUME, and POWER. OW THE...
code 887, and then repeat the instructions for the VCR using code 797. Put the remote in TV mode to use the TV or VCR mode to use the VCR. IMITED You can program your remote control in Limited Mode to keep from accidentally changing the channel on your TV or VCR.
EMOVING IXED HANNEL Press and hold the TV or VCR mode button until all four mode lights illuminate. Press the STAR (*) key followed by two zeros (*00). Press the POUND (#) key. The TV or VCR mode button flashes three times.
Page 17
Instructions If you want to program See Limited Mode on page 3 for Limited Mode, press 1. more information. If not, skip to step 7. Press POUND (#). If you entered the code correctly, the mode button flashes three times. Press POWER to turn off If the code works, the the equipment.
CANNING FOR QUIPMENT Instructions Turn the equipment on. Use the equipment’s front panel buttons or its remote control. Press and hold the mode For example, hold the TV mode button until all the other button for a TV until all of the mode buttons light up, and other mode buttons light.
Instructions Turn the equipment back Press POWER to turn the on and try some other equipment back on. Try some buttons to make sure they other buttons to make sure they work. work. Sometimes POWER works when other buttons don’t. If necessary, repeat this You may need to repeat the scan procedure until you’ve tried...
EMOTE TO AUX M ECEIVER IN If you have another DISH Network satellite receiver installed, you can use this remote in AUX mode to control it along with your new receiver. When you program the remote to control the other receiver, the remote sends out IR and UHF (not UHF Pro) signals to the receiver.
Note: If you aren’t sure how to access the System Info screen or if there isn’t a SYSTEM INFO button on the front panel of your receiver, check your receiver’s User Guide. Write down the address shown: Press and hold the AUX button until all the other mode buttons light up, and then let go of the button.
Page 22
Instructions For AUX mode, the first group of flashes tells you what type of device the AUX mode controls, then the following flashes tell you each digit of the equipment code. A quick flash (zero) before the three-digit code is for a TV; one regular flash is for a VCR or DVD player;...
On/Off command when trying to ensure the satellite receiver is reliably in one state or the other. To use discrete power commands, complete the following: Program the DISH Network remote to the desired remote address (see Changing the Remote and Receiver Address in the next section).
VOIDING EMOTE ONFLICTS When your remote control uses UHF, you may experience interference from other nearby remotes. In situations where neighbors are near (apartments, townhouses, etc.), your receiver could be picking up signals from your neighbors’ remotes. The instructions in this section describe how to avoid remote conflicts.
UHF F HANGING THE REQUENCY —DISH P -DVR 942, D WITCH LAYER DVR V P 622 DVR, DVR O All receiver models, except the DISH Player-DVR 942, ViP 222, ViP 622 DVR, and ViP 722 DVR, must use switch position A or the remote does not control the receiver.
TV1 UHF P ETTING DVR 522 DVR 625 O Use these special instructions only if you are going to use the green 1 UHF Pro key to control the TV1 side of your DuoDVR 522 or 625 (also known as DISH Player-DVR 522 or 625). When you are finished setting up the remote control, you’ll be able to operate the TV1 side of your DuoDVR 522 or DuoDVR 625 from long distances.
Page 27
Use the ARROW buttons to move the highlight to the TV1 Rem Addr box as shown below). This is remote address (the important—if you do not move the highlight, your remote changes the receiver's TV2 remote address (the box) and causes your Remote Control 1 to control the TV2 side of your receiver.
Page 32
VCR C ODES ONTINUED Yamaha 581 592 594 682 Zenith 500 501 533 779 DVD P LAYER ODES Programming in AUX mode: Use these codes to program in VCR mode; if programming in AUX mode, press 1 before entering the DVD Player code.
Page 34
TV/DVD C OMBO ODES Programming for combination equipment: Program the remote control in TV mode using the TV code and then in VCR mode (or AUX—press 1 before entering the DVD code) using the DVD code. TV Code Apex Broksonic Cytron Panasonic Sansui...
Page 35
TV/VCR/T UNER OMBO ODES TV Code Panasonic VCR/DVD C OMBO ODES Programming for combination equipment: Program the remote control in VCR mode using the VCR code and then DVD in AUX mode (press 1 before entering the DVD code) using the DVD code. VCR Code Go Video No Code...
ROUBLESHOOTING What’s What’s Wrong Happening While If you don’t press Start over again. performing a a button for 20 remote control seconds in a procedure, the programming remote control sequence, the remote stops working. shuts off its programming function. You cannot find The keys have two Turn the keys over until you find the the key(s)
Page 37
What’s What’s Wrong Happening Your remote • The remote control • Make sure the remote control is in the control isn’t is in the wrong correct mode. For example, if you want working mode. to use the satellite receiver, put the remote control in Remote Control Modes on page 1).
This warranty extends only to the original user (“you,” “your”) of the DISH Network remote control and is limited to the purchase price of the remote control. DISH Network and its affiliated companies (“we,” “our,” “us”) warrant this remote control against defects in materials or workmanship as follows.
Page 39
ETWORK XCHANGE ROGRAMS DISH Network offers two options if you need to replace your remote control; the Advanced Exchange Program and the Post Receipt Exchange Program. Advance Exchange Program The Advanced Exchange Program allows you to have a replacement remote shipped immediately to you.
Page 40
Review this User Guide. See Troubleshooting on page 24. Call the Customer Service Center at 1-800-333-DISH (3474). Have the date of purchase and your customer account number ready. a. If the representative finds you should return the remote control, you’ll get a telephone number to call for a Return Authorization (RA) number.
Page 41
Inverness Circle East, Englewood, Colorado 80112. Document Number: 167820 Printed in DISH Network is a trademark and service mark of DISH Network. All product names, trade names, or corporate names mentioned in this Guide are acknowledged to be the proprietary property of the...
Page 47
If you enter a “1” as the last number of your code, your remote is in Limited Mode (see page 3 for more details). To read out your remote codes, see page 9 for instructions.
Page 48
For all your customer needs, call the Customer Service Center at 1-800-333-DISH(3474) 167820...