Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Da-Lite Manuals
  4. Projector Accessories
  5. Multi Format Imager
  6. Instruction book

Da-Lite Multi Format Imager Instruction Book

Hide thumbs Also See for Multi Format Imager:

Advertisement

Quick Links

Download this manual
INSTRUCTION BOOK FOR
Multi Format Imager

Advertisement

loading

Related Manuals for Da-Lite Multi Format Imager

Summary of Contents for Da-Lite Multi Format Imager

  • Page 1 INSTRUCTION BOOK FOR Multi Format Imager...

  • Page 2: Important Safety Instructions

    4. Do not operate appliance if it has been dropped or damaged until it has been examined by a qualified service technician. Multi Format Imager Assembly Preparation: Have ample space for this available on a flat clean surface such as a large table or floor. The work area should be larger than the frame size.
  • Page 3 Multi Format Imager Assembly Frame Assembly: 1. In the hardware package, you will receive (12) #10 x .375" long button head screws and (8) #10 x .500" long button head screws required for frame assembly. 2. Lay frame pieces out on floor or table as shown in Figure 1. The right and left side frame assemblies have the rollers and motors attached to them.
  • Page 4 Multi Format Imager Assembly 4. Fasten (3) #10 x .375" long button head screws through top of frame into the corner connector bracket. See Figure 5. Tighten two set screws on flat "L" bracket to line up the front faces as shown in Figure 6.
  • Page 5 Multi Format Imager Assembly 7. Finish assembling corner assembly by inserting (3) #10 x .375" long button head screws through bottom of frame into the corner L connector bracket. Tighten two set screws on flat "L" bracket to line up the front faces as shown in Figure 10.
  • Page 6 Multi Format Imager Assembly 9. Assemble top right and bottom right corner assembly by inserting (3) #10 x .375" long button head screws through bottom of frame into the corner L connector bracket. Tighten two set screws on flat "L" bracket to line up the front faces as shown in Figure 12.
  • Page 7 Multi Format Imager Assembly 11. Untape black steel wire tension cable from bottom left side assembly. Un-wire tie the cable assembly. Run black steel wire tension cable down around pulley at end and bring back towards the end. You may have to pull slightly hard and clip the tension cable to the eyebolt secured in the slat bar as shown in Figure 14.
  • Page 8 Multi Format Imager Assembly 12. Assemble pinch guard bracket using (2) #10 x .375" long button head screws to opposite side of pulley bracket as shown in Figure 15. Repeat this step for bottom right corner of screen. Fasten Screws Through...
  • Page 9 Multi Format Imager Assembly 14. Assemble pinch guard bracket using (2) #10 X .375" long button head screws to opposite side of pulley bracket as shown in Figure 17. Repeat this step for top right corner of screen. Figure 17...
  • Page 10 Check to make sure both brackets are vertically level with each other. 2. To install the Multi-Format Imager over a Da-Lite Perm-Wall screen you will need to place the supplied wooden spacers 5. Drill hole for mounting bracket in to wall. Dimension for hole between the screen and the wall.
  • Page 11 Multi Format Imager Installation 6. Wall hanging brackets must be evenly spaced across top of frame. Measure the frame width and divide by three then make two marks from the end. The center of each wall bracket shall be located on those marks.
  • Page 12 Multi Format Imager Installation 7. Hang the frame assembly on the hanger brackets as shown in Figure 22. Be careful as bracket is to slide in front of the aluminum guide channel. There is a lip on the back of the frame that wedges itself in to the hanger bracket once fully installed on bracket.
  • Page 13 Multi Format Imager Wiring Diagram 1. To connect power to unit locate junction box cover on bottom frame assembly. There will be two black screws holding the wiring box cover on as shown in Figure 25. Figure 25 Remove Two...
  • Page 14 Multi Format Imager Wiring Diagram 3. Connect IR eye to splitter for screen operation. IR eye shall be plugged into a QEYE port on the primary splitter as shown in Figure 27. 6P4C Figure 27 RJ-14 Cable RJ-22 +12V Blue...
  • Page 15 Multi Format Imager Intermediate Stop Adjustment 1. To adjust intermediate stopping positions make sure both 3. Once both masks are at the desired stopping position. Press masks are completely retracted into the frame. Press the left and hold Preset 1, Preset 2 or Preset 3 button on remote for mask ">"...
  • Page 16 Multi Format Imager Limit Travel Adjustment 12. To adjust how far the mask travels outward towards the 6. Locate the two tactile buttons on the back of the switch. They are square silver with black round buttons as shown middle of masking screen, press and hold the up tactile in Figure 30.

  • Page 17: Troubleshooting

    Troubleshooting Visit www.da-lite.com/products/product_videos.php to find contact us by email at info@da-lite.com or by phone at (800) installation and troubleshooting videos and tutorials. You will 622-3737 or (574) 267-8101 with any troubleshooting questions. also find a link to Live Chat for interactive support and you can...
  • Page 20 OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE. In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, (574) 267-8101, (800) 622-3737.