Assembling Rip Fence - Delta TS350 Instruction Manual

ATTACHING THE GUIDE RAILS
1. Align the three slotted holes in the front right guide rail (A) Fig. 16, with two holes (B) in saw table and slotted hole (C)
in extension wing. Insert a M6 x 1 x 20mm carriage head screw (D) Fig. 14, through the three holes in the front right
guide rail, and the saw table. Place a M6.4 flat washer (E), and a 6.1 lockwasher (F) onto the carriage head screw (D).
Thread an M6 x 1 hex nut (G) onto the carriage head screw (D) and hand tighten only.
NOTE: Hand-tighten all hardware in Steps 1-9 for further adjustment.
2. Insert the longer end of the front guide rail extension connector (H) Fig. 17 into the end of the guide rail (A).
3. Attach the front left guide rail (J) Fig. 18 on the extension connector (H). Align the two slotted holes in the guide rail
extension (J) Fig. 16 with the hole (K) in the table and the extension wing (L). Insert an M6 x 1 x 20mm carriage head
screw (D) Fig. 16 through the two holes in the front left guide rail and the saw table. Place an M6.4 flat washer (E)
and a 6.1 lockwasher (F) on the carriage head screw (D). Thread a M6 x 1 hex nut (G) on the carriage head screw (D).
4. Fig. 19 illustrates the front guide rail loosely attached to the table saw.
5. Align the holes in the longer section of the rear guide rail (P) Fig. 20 with the holes (A), (B), and (C) in the saw table.
Place an M8.1 lockwasherand an M8.4 flat washer on an M8 x 1.25 x 16mm hex head screw. Insert the screw
through the hole (A) Fig. 20 in the rear guide rail. Place an M8.4 flat washer and an M8.1 lockwasher on the hex head
screw. Thread a M8 x 1.25 hex nut onto the hex head screw.
6. Place an M8.1 lockwasher and an M8.4 flat washer on an M8 x 1.25 x 16mm hex head screw. Insert the screw
through the holes (B) and (C) Fig. 20 in the rear guide rail and into the tapped hole in the saw table.
7. Align the holes in the shorter section of rear guide rail (R) Fig. 21, with holes (D) and (E) in the in the saw table. Place
an M8.1 lockwasher and a a M8.4 flat washer onto a M8 x 1.25 x 16mm hex head screw. Insert the screw through
the hole (E) Fig. 21, in the rear guide rail. Place a M8.4 flat washer and a M8.1 lockwasher onto the hex head screw.
Thread a M8x1.25 hex nut onto the hex head screw.
8. Place a M8.1 lockwasher and a M8.4 flat washer onto a M8 x 1.25 x 16mm hex head screw. Insert the screw through
the hole (D) Fig. 18 in the rear guide rail and thread into the tapped hole in the saw table.
9. Use a square (X) Fig. 21 or a ruler to adjust the rail, so that it is 7/16" from top of the table along the entire length.
10. Tighten all mounting hardware.

ASSEMBLING RIP FENCE

1. Insert the handle (A) Fig. 22 into the threaded hole (B) in the rip fence (C)
2. Insert a flat-head screwdriver into the rip fence handle (A) Fig. 23. Tighten the screw.
3. Tighten the hex nut (D) Fig. 23 against the fence body..
C
Fig. 22
B
A
Fig. 23
14 - English
A
D