Turning On The Appliance; Change The Program; At The End Of The Wash Cycle; Changing Washing Program - Whirlpool ADP8000 Instruction Manual

Starting a cycle wash
Open the door, draw
1
It is recommended to load the lower basket first, then the upper one (see the section entitled
"
Loading the Dishwasher ).
2 Pour in the detergent (see the section entitled Detergent and Rinse Aid ).
3 Ensure that the dis hwasher is connected to the p owe r supply, th e water is connected an d
turned on and the drain hose is connected correctly.
4 Close the door, press the power button, and the power indicator light will turn on.
5 Press the program button to select the desired wash program, then press the Start/Pause button
and the dishwasher starts.
When you press the Start/Pause button to pause during washing, the program light
will stop blinking and the dishwasher will sound every minute unless you press the
Start/Pause button to start.
Premise:
1 A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled.
2 Press the Start/Pause button and then press the program button for
in a standby state. On in standby state, you can change the program to the desired cycle setting (see the
section entitled " Starting a washing program" ).
3 The program indicator lights show the state of the dishwasher:
a)
The selected program indic ator is flashing-->The progra m is running.
b)
The selected program indic ator is on but not flashing-->The dishwasher is in stan dby state or pause.
c)
Some of the progra m li ghts are flashing more qu ickl y-->Error
If you open the door
will stop blinking and the buzzer will sound every minute unless you close the door .
After you close the door ,the machine will keep on working after 10 seconds.
If some of the program lig hts keep flashing very q uickly afte r the warning soun d, that indicates that the
machine is out of order, please note do wn which lights are flashing, turn off the main power and wa ter
supply before calling for a service (see the section entitled Error co des ).
A forgotten dish can be added any time before the detergent dispenser opens.
1
Press the START/PAUSE button.
2 After the spray arms stop working, you can open the
door completely.
3
Add forgotten dishes.
W hen the working cycl e has finished, the bu zzer of the d ishw ash er w ill sound for 8 seconds, t hen stop . Turn off
the applia nce using the po wer button, shut off the water supp ly and open the doo r of t he dishw asher.
Wait f or a few minutes before u nloading the dishwasher to a void handling the dishes and utensils while they
are still hot an d more susce ptible to breakage. They will also dry bett er.
Switch Off the Dishwasher
1.Switch off the dishwasher by p ressing t he power button.
2.Turn o ff th e water tap.
Open the door carefully
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down be fore rem oving from
the appliance.
Open the dishwasher's door, leave it ajar and wai t a few m inut es before remov ing t he dishes. In this way they
will be cooler an d the drying will be improved.
out the lower and upper basket, load the dishes and push them back.
"
during a wash cycle
It is dangerou s to ope n the door when w ashing, beca use the hot wate r ma y scald you.
"
more than 3 seconds
(see the section entitled " Error codes " ).
, the machine will pause. The program light
"
4
Close the door.
5
Press the START/PAUSE button, the dishwasher will run
after 10 seconds.
11
"
to put the machine
"