Page 1
AutoDome Easy VEZ Series Installation and Configuration Manual...
Page 2
AutoDome, Bilinx, Bosch, the Bosch logo, DiBos, FastAddress and VIDOS are registered trademarks of Bosch Security Systems, inc. The following trademarks are registered with the United States Patent and Trademark Office: Pentium is a registered trademark of Intel Corporation .NET, DirectX, Internet Explorer, Microsoft, Windows, Windows 2000 and Windows XP are registered trademarks of Microsoft Corporation Due to the nature of this material, this document refers to numerous hardware and software products by their trade names, In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies in the United States of America.
Page 3
DANGER! Danger messages denote the presence of electrical equipment that may cause electric shock or electrocution. Take care when you see this symbol to avoid serious injury or death. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
| AutoDome Easy Customer Support and Service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Service Centers Phone: 800-366-2283 or 585-340-4162 Fax: 800-366-1329 Email: cctv.repair@us.bosch.com Technical Support Phone: 800-326-1450 Email: technical.support@us.bosch.com...
Unauthorized substitutions may result in fire, electrical shock or other hazards. 9. Safety Check - Upon completion of servicing or repairs to the unit, ask the service technician to perform safety checks to ensure proper operating condition. Bosch Security Systems, Inc.
The equipment must not exceed its maximum operating could void the user’s authority to operate the temperature requirements. equipment. 2. Mechanical Loading - When rack-mounting the equip- ment, ensure that a hazardous condition is not created by uneven mechanical loading. Bosch Security Systems, Inc.
Page 7
ON. Le débranchement ment, this product may cause radio interference, in which du cordon d'alimentation permet de couper l'ali- case, the user may be required to take adequate measures. mentation des appareils. Bosch Security Systems, Inc.
Wenn das Netzkabel aus der Steckdose cuando el interruptor está en la posición de gezogen wird, ist die Spannungszuführung zum encendido. El cable de alimentación es la principal Gerät vollkommen unterbrochen. fuente de desconexión de todas las unidades. Bosch Security Systems, Inc.
Page 9
ON-OFF si trova nella uitschakelaar aan staat. Het netsnoer is de "hoofd- posizione ON. Il cavo di alimentazione costituisce schakelaar" voor alle apparatuur. il dispositivo di scollegamento dell'alimentazione principale per tutte le unità. Bosch Security Systems, Inc.
Page 10
WL-WYL znajduja sie podnapieciem, jezeli tylko przewód zasilajacy jest polaczony zezródlem zasilania. Jed- nakze urzadzenie dziala tylko wtedy, gdywylacznik znajduje sie w polozeniu WL. Przewódzasilajacy jestglównym odlacznikiem zasilania dla wszystkich rodzajówurzadzen. Bosch Security Systems, Inc.
Page 11
Safety Precautions | en Bosch Security Systems, Inc.
Page 12
| Safety Precautions Bosch Security Systems, Inc.
Installing the Base to the Mounting Plate 8.1.4 Powering On 8.1.5 Installing the Base to a Junction Box Basic Operation Keyboard Control Command Structure Program and Operation 10.1 Menu Navigation Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
Page 14
Initialize Camera Menu Dome Setup Menu 17.1 Home Function 17.2 Initialize Dome Menu 17.3 Dome Information Menu Keyboard Commands by Number Troubleshooting Preventive Maintenance Spare Parts List December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Verify that all the parts listed in Section 1.1: Parts List are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.
Do not allow children or unauthorized personnel to use the device. • Do not block any ventilation openings. • Keep this manual for future reference. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
The AutoDome Easy can be surface or wall mounted. The appropriate mount should be installed before installing the AutoDome Easy. For specific directions on mounting the unit, see the man- ual that came with your mount. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
Biphase (shielded 2-wire, half-duplex, multi-drop, 1.2 km (4000 ft.) cable limit), is the stan- dard Bosch protocol used to send Pan/Tilt/Zoom control over 2-wire shielded twisted pair (STP). The AutoDome Easy has an internal 110 Ω termination resistor between the biphase(+) and biphase(-).
Connect shield of the cable to the Head End controller. Head End AutoDome Easy Biphase Brown Black Not Connected X SHIELD Fig. 5.1 Biphase Direct Control Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
Alarm Common Blue Wire Contact Alarm Input Violet Wire Fig. 5.3 N.O. - Normally Open Non-supervised Connections NOTICE! All the connectors marked GND are common. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
Carefully lift the bubble and set it aside. Locate the SW501 switch. Set the switches based on Table 6.1. Fig. 6.1 Setting the AutoDome Easy Address (ID) December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Page 23
AutoDome Easy Address (ID) Address Address Table 6.1 ID Settings Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
PDome Camera Protocol Function S/W No. Function NTSC NTSC/PAL Table 7.1 Dome Camera Function No. 9 No. 0 Protocol Biphase Table 7.2 Dome Camera Protocol Function December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Locate the curved indentation (see Figure 8.1, Reference # 5) to mark the center of the hole. Drill or cut the appropriate size hole required for the cables. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
Connect the prepared wiring in Section 5: Connections matching the colors of the wires. Fig. 8.2 Connecting the Cables Align the dome camera with the mounting bracket. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
During the homing phase, the camera pans left and right and tilts up and down. It also adjusts the lens focus. The entire homing phase lasts approximately 40 sec- onds and displays the following splash screen throughout its homing phase START UP BOSCH Version 2.0.x.
Depending on the type of keyboard, the control function keys are labeled: • ON or AUX ON • OFF or AUX OFF • SET or SET SHOT • SHOT or SHOW SHOT December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Controls miscellaneous dome operations such as: OSD, auto pivot, home function, and initialization (reset to factory defaults). Exit Exits the menu without saving the data. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
All preset positions must be set in sequential order. To verify the next number in the sequence, enter the Preset menu and scroll through the saved presets. The last number displayed is the next available preset position. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
The next sequential character is changed to a blank space, twist the joy- stick and repeat step 5. When satisfied with the title, select SAVE AND EXIT. To exit without saving, select EXIT W/O SAVE. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
The next sequential number is changed to blinking = =, twist the joystick and repeat step 8. 10. When satisfied with the preset tour, select SAVE AND EXIT. To exit without saving, select EXIT W/O SAVE. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Press ON + 5 + ENTER to gain access of the CONTROL. When finished selecting the cam- era’s tilt and zoom, press OFF + 5 + ENTER. Select END POINT. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
Exits the menu without saving the data. NOTICE! Sector titles are displayed any time the camera moves and disappears three (3) seconds after the camera stops. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
OFF + 6 + 5 + ENTER. Momentary can only be released with the following sequence: press OFF + 6 + 5 + ENTER. Bosch Security Systems, Inc. Installation and Configuration Manual...
OFF - Turns off digital zoom. optical zoom. Save and Exit Saves the data and exits the menu. Exit W/O Save Exits the menu without saving the data. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Saves the data and exits the menu. Exit W/O Save Exits the menu without saving the data. *Automatically adjusts the camera to the current light level, when in manual mode. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
1000, 2000, 5000, 10000 in shutter PRI and man- ual mode only. Bright Reduces the camera's iris Allows a range of 0-90. level for proper expo- sure. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Page 39
Exit W/O Save Exits the menu. Mode Iris Gain Shutter Brightness Back Light Auto Shutter PRI Iris PRI Manual Table 16.1 Mode Options Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
Save and Exit Saves the data and exits the menu. Exit W/O Save Exits the menu without saving the data. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
CAMERA WILL BE INITIALIZED!! ARE YOU SURE? CAMERA SETUP MENU CAMERA WILL BE INITIALIZED!! FOCUS CONTROL ARE YOU SURE? WB CONTROL AE CONTROL L/L CONTROL PICTURE INITIALIZE CAMERA EXIT Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
Displays the firmware version number. Save and Exit Saves the data and exits the menu. Exit W/O Save Exits the menu without saving the data. December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Save and Exit Saves the data and exits the menu. Exit W/O Save Exits the menu without sav- ing the data. Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...
DOME INFORMATION LANGUAGE: ENGLISH VERSION: 2.0.0 OSD DISPLAY: OFF EXIT AUTO PIVOT: ON HOME FUNCTION INITIALIZE DOME DOME INFORMATION SAVE AND EXIT EXIT W/O SAVE December 06, 2006 | F01U074570 | 3.0 Installation and Configuration Manual Bosch Security Systems, Inc.
Factory P/T home position Set–recalibrate home position. Shot “201- Run tour Activates preset tour 1-4. 204” Shot “301- Run auto pan Activates auto pan 1-4. 304” Bosch Security Systems, Inc. Installation and Configuration Manual December 06, 2006 | F01U074570 | 3.0...