Additional Requirements 6.1.2 Preparing the Ceiling for Installation 6.1.3 Installing the Camera to the Mounting Plate Installing a Pipe Mount Description 7.1.1 Tools/Supplies Required 7.1.2 Preparing the Ceiling for Installation Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 4
| Table of Contents AutoDome Easy II 7.1.3 Installing the Camera to the Mounting Plate Index F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
12. Install in accordance with the manufacturer's instructions in accordance with applicable local codes. Use only attachments/accessories specified by the manufacturer. Equipment change or modification could void the user's guarantee or authorization agreement. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 6
You can view and print the full version of this Installation Manual with Adobe Acrobat Reader, both provided on the enclosed CD-ROM. This user guide is the intellectual property of Bosch Security Systems; protected by copyright. Contact: www.BoschSecurity.com F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.
Installation manual Quantity Part In-ceiling mount: VEZ-A2-IC White trim ring with 2 (two) M3 captive screws Black trim ring with 2 (two) M3 captive screws Recess mount assembly Installation manual F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
This installation should be made by qualified service personnel and conform to the National Electrical Code and applicable local codes. NOTICE! A grounded conduit is required in order to meet the EMC Regulation Requirements. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Prolonged exposure to bright lights may cause bleaching of the sensor's color filters. This will be visible as colored spots in the picture and is irreversible. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Surface Mount. Determine a secure location for the surface mount dome. ø 153.0 (6.02) 134.7 (5.3) R50.6 (1.99) Figure 4.1 Indoor Surface Mount Dimensions Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 12
Junction Box Holes Cable Hole (40 mm maximum); Crescent Shape Mounting Plate Junction Box Skip to Section 4.1.4 Installing the Camera to the Mounting Plate, page 17, to continue the installation. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Box as a template to mark the location of the four (4) M4 or #10 pan head screws (Item 1, below). Figure 4.5 Location of M4 or #10 pan head screws Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 14
Surface Mount Junction Box. These parts are supplied with the AutoDome Easy II Outdoor Camera. Ensure that the side of the retaining ring with the counter-sunk screw holes is facing you. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 15
Note: For an outdoor installation ensure that the four (4) 3.97 mm I.D. by Ø1.78 mm O-rings are threaded onto the four (4) M4 or #10 user-supplied pan head screws. Refer to step 5. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 16
Figure 4.8 Install the Mounting Plate Junction Box Holes Cable Hole (40 mm maximum); Crescent Shape 13. Skip to Section 4.1.4 Installing the Camera to the Mounting Plate, page 17, to continue the installation. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
(see the AutoDome Easy II User Manual for wiring information). Unlock the single safety locking screw on the base of the unit using the user-supplied Allen wrench. Figure 4.9 Unlock Safety Locking Screw Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 18
Attach the camera to the mounting plate by inserting the vertical tab into the recessed slot on the top of the camera dome to the right of the safety locking screw. Figure 4.11 Attach Safety Locking Screw F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 19
10. Outdoor Installation: Thread the 2.89 mm I.D. by Ø1.78 mm O-ring (item 1, below) onto the Safety Screw. 11. Secure the safety locking screw with the user supplied locking torx wrench (T-10). Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Prolonged exposure to bright lights may cause bleaching of the sensor's color filters. This will be visible as colored spots in the picture and is irreversible. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Determine a secure location for the wall mount (supplied separately). 334.0 (13.1) 301.0 (11.8) 188.0 (7.4) 203.5 (8.01) 280.0 (11.02) Figure 5.1 Wall Mount Dimensions Fit a user-provided metal single-gang junction box to the wall. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 22
Feed all wires from the metal junction box through the arm. Attach the mounting cap to the arm. Fit the arm to a metal single-gang junction box. Figure 5.3 Fit to Gang Junction Box F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
The fasteners and mounting surface must be capable of supporting a maximum load of 11.33 kg (25 pounds). 334.0 (13.1) 301.0 (11.8) 188.0 (7.4) 203.5 (8.01) 280.0 (11.02) Figure 5.4 Wall Mount Dimensions Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 24
CAUTION! You must ensure that the gasket is attached to the retaining ring as shown above to ensure an environmentally tight seal. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 25
Feed the wires through the hole in the surface, through the wall mount flat gasket (item 1, Figure 5.6) and then through the arm. CAUTION! All wires for installation applications must be routed through a grounded conduit. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 26
AutoDome Easy II Outdoor Camera. Figure 5.6 Secure arm to wall with flat gasket Skip to Section 5.1.4 Installing the Camera to the Mounting Plate, page 26, to continue the installation. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Attach user supplied ground to junction box. Connect the mating connectors with the flying leads to the user supplied wiring (see the AutoDome Easy II User Manual for wiring information). Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 28
Plug the matching connectors from the camera into the mating connectors from the ceiling. Figure 5.9 Connect Cables Align wires on side of mounting plate with crescent shaped cut-out. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 29
10. Rotate the camera approximately 15 degrees to the right and lock firmly into place, as shown in the next illustration. Note: Do not loosen brass mounting buttons. Figure 5.11 Attach Dome to Mounting Plate Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 30
12. Secure the safety locking screw with the user supplied locking torx wrench (T-10). 13. Pull excess wire back into the mount tube. 14. Confirm that the housing is electrically grounded. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
LTC 9349MK mounting kit is recommended (supplied separately). See the instruction book supplied with the mounting bracket for installation instructions. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 33
Ensure clamping plates are angled inward by pushing up and into the two slots. Bracket with plate should be in the lower position for AutoDome Easy II analog models. Figure 6.3 Adjust Mounting Clamps F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 34
(41.7 mm (1.64 in.) maximum ceiling thickness and 12.7 mm (0.50 in.) minimum ceiling thickness). Figure 6.4 Attach Recess Mount to Ceiling Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
CAUTION! All wires for installation applications must be routed through a grounded conduit. Attach grounding wire from unit to the mounting bracket. Attach user supplied ground to junction box. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 36
Plug the matching connectors from the camera into the mating connectors from the ceiling. Figure 6.7 Match Connectors Locking Screw Crescent Shape Mounting Plate Vertical Tab Align wires on side of mounting plate with crescent shaped cut-out. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 37
Note: Do not loosen brass mounting buttons. Figure 6.9 Attach Dome to Mounting Plate Recess Mounting Bracket Mounting Plate Mounting Bracket Tether Point F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 38
14. Use supplied T-10 wrench to secure the trim ring’s two (2) safety locking screws to the mounting bracket. 15. Snap trim ring into place. Ensure snaps are secure by attempting to lightly turn unit. Note: Unit should not turn. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Prolonged exposure to bright lights may cause bleaching of the sensor's color filters. This will be visible as colored spots in the picture and is irreversible. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Determine a secure hard surface location for the ceiling pipe mount (supplied separately). 88.8 (3.5) 88.8 (3.5) 736.0 (28.98) 3/4-14 NP 529.0 SM Threads (20.83) Ø11.2 (4x) (0.44) 429.0 (16.89) Ø153.0 Figure 7.1 Pipe Mount Dimensions Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 41
(11.8 in.), or combine the two (2) pipes with the integral coupler for 505 mm (20 in.). Outdoor Installation: Apply the following O-rings (supplied with the AutoDome Easy II Outdoor Camera) to the locations specified below: F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 42
Thread a 29.74 mm I.D. by Ø3.00 mm O-ring (item 2, above) between any interface between a pipe and a coupler. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 43
Fit the dome cap to the bottom of the pipe. Outdoor Installation: Apply the following O-ring and the retaining ring (supplied with the AutoDome Easy II Outdoor Camera) to the locations specified below: F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 44
Secure the flange using four (4) appropriate user-provided fasteners such as Moly or Toggle bolts. Outdoor Installation: Place the flat gasket (item 1, below) between the flange and the surface before securing. Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 45
Figure 7.5 Attach Pendant Pipe Mount to Ceiling CAUTION! Select a rigid mounting location to prevent excessive vibration to the AutoDome Easy II Camera. 10. Attach user supplied ground lug. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 46
(3) screws supplied (Figure 1.6). Figure 7.6 Attach Mounting Plate to Dome Cap Crescent Shape Ground Lug Dome Cap Mounting Plate Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 47
Figure 7.7 Unlock Safety Locking Screw Plug the matching connectors from the camera into the mating connectors from the ceiling. Align wires on side of mounting plate with crescent shaped cut-out. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 48
Rotate the camera approximately 15 degrees to the right and lock firmly into place, as shown in the next illustration. Note: Do not loosen brass mounting buttons. Figure 7.9 Attach Dome to Mounting Plate Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 49
11. Secure the safety locking screw with the user supplied locking torx wrench (T-10). 12. Pull excess wire back into the mount tube. 13. Confirm that the housing is electrically grounded. F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 50
DVR 9 image sensors 10 installing base 17 drywall ceiling 11 surface mount 17 mounting plate 44 multiplexer 9 pendant pipe mount 43 preparing drywall ceiling 11 recess mount 30 Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 51
| Index AutoDome Easy II F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 52
AutoDome Easy II Index | en Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 53
| Index AutoDome Easy II F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 54
AutoDome Easy II Index | en Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 55
| Index AutoDome Easy II F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
Page 56
AutoDome Easy II Index | en Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02...
Page 57
| Index AutoDome Easy II F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.