User’s Guide www.fetco.com Models: CBS-2051 CBS-2052 CBS-2052 NOTICE TO INSTALLER: Please leave this book with the machine. Table of Contents Contact Information ..........2 Programming ............10 Description & Features ..........2 Batch Settings .............10 Specifications............2 Temperature Settings .........11 Requirements............2 Advanced Settings and Diagnostics ....11 Weights and Capacities ........2 Relay Test ............12 Electrical Configuration and Brewing Efficiency ...3...
5. Verify that the water line will provide at least 1 gallon per minute for the CBS-2051e, and 1.5 gallons per minute for the CBS-2052e and 2052e20, and that the water pressure is between 20 and 75 psig. 6. Use a wrench on the factory fitting when connecting the incoming water line. This will reduce stress on the...
Page 7
WIRE 208-240V The CBS-2052e and CBS-2052e20 are shipped from the factory configured for either single phase or three phase operation, depending on the version that was ordered. A tag attached to the terminal block will indicate which way the unit was configured.
Page 8
Final Setup 1. Turn on the incoming water supply line and inspect both inside and outside of the brewer for leaks in all fittings and tubes 2. Turn on the incoming power. 3. Press the brewer’s main power switch, which is hidden behind the front leg of the brewer.
Operating Instructions Control Panel Functions Only switches that are active are illuminated. Switches that are inactive or disabled are invisible. Main Power Switch Controls all power to brewer Indicator lamp at top of panel. Control Panel On/Off Switch Secondary power switch. Does not disconnect main power.
The display will show the software version. Example: 0.0 4.8 Press STOP to continue. Batches are numbered 1 – 3 or 1 – 6 (CBS-2051e) (CBS-2052e / 2052e20) PARAMETER BATCH # SETTING 1.1 1.50 Example: Left Side – Large Batch – Volume 1.5 Gal.
31 - 52 Must be set for the correct model number of the Number brewer: 51 for CBS-2051e, 52 for CBS-2052e and CBS-2052e20. Reload Defaults 0 - 1 Changes all settings to default factory settings. 0 = Do not reload defaults...
Address Description Range Default Comment Left Brew Valve 0.09 – 1.49 0.92 Flow Rate If #59 is GAL Right Brew Valve Use this to compensate for minor discrepancies in Flow Rate actual volume versus programmed volume. Set lower to increase volume, higher to decrease 0.33 –...
Error Codes How to Clear Error Code Description Possible Cause Corrective Action Codes Internal Error Control board failure. Clear error. Turn main power System had to reload Re-program the brewer to switch off and on. default settings. the desired specifications. If error occurs again, replace control board.
Parts Figure 1 – CBS-2051e Main Assembly DWG 101191-B ITEM # PART # DESCRIPTION 001049 WELDMENT CBS-2051e 57006 FILL VALVE, S-53 120VAC EXPORT 57017 FILL VALVE, S-53 220VAC 220V ONLY 24012 GASKET, S-53 FILL VALVE 31078 FITTING, S-53 FILL VALVE INLET 03074 BRACKET, S-53 82020...
Page 15
15007 STANDOFF, MALE-FEMALE, THREADED HEX 4-40-1/2" 29007 NUT, #4-40 KNURLED THUMB 51042 BOARD, POWER SUPPLY-120VAC EXPORT 51055 BOARD, POWER SUPPLY-220VAC 220V ONLY 29019 SPACER, .25" HEX x 1" LG., FEM, #4-40 THREAD 65002 CONNECTOR, COPPER LUG 52050 TERMINAL BLOCK 83026 WASHER, INTERNAL TOOTH LOCK, #8 SCREW SIZE, 104029 ASSEMBLY, TANK CBS-2051e...
Page 16
Figure 2 – CBS-2051e Tank Assembly DWG 104029-C ITEM # PART # DESCRIPTION 4039 WELDMENT, TANK CBS-2051e 83041 WASHER, .812"OD X .412"ID, FLAT 31005 FITTING, 90 ELBOW, 1/4 HOSE ID X 1/8 MPT 31116 LOCKNUT 1/8 STRAIGHT PIPE THREAD 83043 WASHER, 1.125"OD X 0.688"ID FLAT 83048 WASHER, 1.250"OD X 0.835"ID FLAT...
Page 17
13072 OUTLET, INSIDE TANK HOT WATER 83042 WASHER, .875"OD X .562"ID, FLAT 31036 FITTING COMPR. MALE CONNECTOR 1/4 TUBE OD X 1/4 MPT 31117 LOCKNUT 1/4 STRAIGHT PIPE THREAD 25098 FITTING, COMPRESSION MALE CONNECTOR 31081 PLUG, HEX HEAD 1/4" MPT 24002 O-RING, TANK COVER 102013...