Fireplace Vent Connection; Mobile Home Installation - Napoleon Torch GT8P Installation And Operation Instructions Manual

Installation and operation manual (84 pages)

Installation and operating instructions manual (88 pages)

Installation and operation instructions manual (22 pages)

Table of Contents

4. Thread the air terminal connector / vent pipe assembly down through the roof. The air terminal must be located vertically

and plumb. Attach the air terminal connector to the roof support, ensuring that the top of the air terminal is 16" above the

highest point that it penetrates the roof. Figure 12. DO NOT CLAMP THE FLEX VENT PIPE.

5. Remove nails from the shingles, above and to the sides of the chimney. Place the ﬂ ashing over the air terminal connector

leaving a min. 3/4" of the air terminal connector showing above the top of the ﬂ ashing. Slide the ﬂ ashing underneath the sides

and upper edge of the shingles. Ensure that the air terminal connector is properly

centred within the ﬂ ashing, giving a 3/4" margin all around. Fasten to the roof. Do

not nail through the lower portion of the ﬂ ashing. Make weather-tight by sealing

with caulking. Where possible, cover the sides and top edges of the ﬂ ashing with

rooﬁ ng material. Figure 14.

6. Aligning the seams of the terminal and air terminal connector, place the terminal

over the air terminal connector making sure the vent pipe goes into the hole in the

terminal. Secure with the three screws provided. Figure 14.

7. Apply a heavy bead of weatherproof caulking 2" above the ﬂ ashing. Note:

Maintain a minimum 2" space between the air inlet base and the storm collar. Install

the storm collar around the air terminal and slide down to the caulking. Tighten to

ensure that a weather-tight seal between the air terminal and the collar is achieved.

Figure 14.

8. If more vent pipe needs to be used to reach the ﬁ replace, couple them together

as illustrated. The vent system must be supported approximately every 3 feet for

both vertical and horizontal runs. Use noncombustible strapping to maintain the

minimum 1" clearance to combustibles. Figure 11.

1. Install the 3" ﬂ exible vent pipe to the ﬁ replace. Secure with 3

screws and ﬂ at washers. Seal the joint and screw holes using Mill

Pac sealant (W573-0007 not supplied).

2. Install the 5" ﬂ exible vent pipe to the ﬁ replace. Attach and seal

the joints using the high temperature sealant W573-0002 (not

supplied).

This appliance is certiﬁ ed to be installed as an OEM (Original Equipment Manufacturer) installation in a manufactured

home or mobile home and must be installed in accordance with the manufacturer's instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard,

CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plate.

A conversion kit is supplied with the mobile home appliance.

This Mobile/Manufactured Home Listed appliance comes factory equipped with a means to secure the unit. The ﬁ replace is

equipped with two 1/4" diameter holes located in the front left and right corners of the base. For mobile home installations,

the ﬁ replace must be fastened in place. Use #10 hex head screws, inserted through the holes in the base to secure. Always

turn off the pilot and the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior

to lighting the ﬁ replace, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home, where not

prohibited by local codes.

This ﬁ replace is only for use with the type of gas indicated on the rating plate. This ﬁ replace is not convertible for use with

other gases, unless a certiﬁ ed kit is used.

Conversion Kits

The mobile home appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (LP).

To convert from one gas to another consult your Napoleon® dealer/distributor.

W415-0619 / B / 03.03.08