Fireplace Vent Connection - Napoleon BGD40-P Installation And Operation Instruction Manual

Natural and propane gas

Hide thumbs Also See for BGD40-P:

Installation and operating instructions manual (104 pages)

Installation and operation instructions manual (36 pages)

Installation and operating instructions manual (36 pages)

Table Of Contents

Table of Contents

6. Aligning the seams of the

terminal and air terminal connector,

place the terminal over the air

terminal connector making sure

the liner goes into the hole in the

terminal. Secure with the three

screws provided.

7. Apply a heavy bead of

weatherproof caulking 2"

above the ﬂ ashing. NOTE:

Maintain a minimum 2" space

between the air inlet base

and the storm collar. Install

the storm collar around the

air terminal and slide down

to the caulking. Tighten to

ensure that a weather-tight seal between the air terminal

and the collar is achieved.

NOTE: All gas connections must be contained within the ﬁ replace when complete.

1. Move the ﬁ replace into position and secure to the ﬂ oor through the 1/4" holes located at either side of the base.

2. The ﬁ replace is designed to accept 3/8" gas supply line.

3. Connect the gas supply in accordance to local codes. In the absence thereof, install according to the

National Installation Code.

4. When ﬂ exing any gas line, support the gas valve so that the lines are not bent

or kinked.

5. Check for gas leaks by brushing on a soap and water solution.

DO NOT USE OPEN FLAME.

Purge all gas lines with the glass door open. Assure that a continuous gas ﬂ ow is at

the burner before closing the door.

CER TIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA 2.33-2002, ANSI Z21.88-2002 VENTED GAS FIREPLACE HEATER / FOYER DE CHAUFFAGE AU GAZ AVEC EVACUA TION

DIRECT VENT GAS FIREPLACE. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE

CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONTRUCTION AND SAFETY STANDARD, TITLE 24

CFR, PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 501A.

FOYER A GAZ VENTILE DIRECT. HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIE POUR INSTALLATION DANS UNE MAISON MOBILE

SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES AU GAZ, EN VIGUEUR AU CANADA OU AUX ETATS-UNIS DE LA NORME DE

SECURITE ET DE CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE REFERER A LA NORME

RELATIVE AU CRITERE DE MESURES DE SECURITE CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURES, LES SITES ET LES COMMUNAUTES, ANSI/NFPA 501A.

MODEL BGD40 - N

ALTITUDE/ELEVATION:

INPUT/ALIMENTATION:

MODEL BCDV400 - N

REDUCED INPUT/ALIMENTA TION REDUIT:

ORIFICE:

MANIFOLD PRESSURE: 3.5" WATER COLUMN

PRESSION AU COLLECTEUR: 3.5" D'UNE COLONNE D'EAU

MINIMUM SUPPLY PRESSURE: 4.5" WATER COLUMN

PRESSION D'ALIMENTATION MINIMALE: 4.5" D'UNE COLONNE D'EAU

MAXIMUM SUPPLY PRESSURE: 7.0" WATER COLUMN

PRESSION D'ALIMENTA TION MAXIMAL: 7.0" D'UNE COLONNE D'EAU

NOT FOR USE WITH SOLID FUEL. FOR USE WITH COVERS AND

GLASS DOORS CERTIFIED WITH THIS UNIT ONLY.

WARNING:

DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN CONTACT

WITH THE FLAMES, OTHER THAN THA T SUPPLIED BY THE MANUFACTURER WITH THE APPLIANCE.

MINIMUM CLEARANCE TO COMBUSTIBLE MA TERIALS /

DEGAGEMENTS MINIMAUX DES MA TERIAUX COMBUSTIBLES:

TOP, FLOOR, SIDES & BACK

DESSUS, PLANCHER, COTES & ARRIERE

RECESSED DEPTH (CORNER INSTALLATION ONL Y)

PROFONDEUR D'ENCASTRE (INSTALLATION DU COIN SEULEMENT)

VENT / EVENT

MANTLE HEIGHT / HAUTEUR DU MANTEAU

MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION HORIZONTALE MAXIMALE: 3". SEE INSTRUC-

TION MANUAL FOR GREATER EXTENSIONS. REFERER AU MANUEL D'INSTRUCTION POUR DES

EXTENSIONS PLUS GRANDES.

MINIMUM AND MAXIMUM HORIZONTAL VENT LENGTHS ARE 10 INCHES AND 20 FEET RESPEC-

TIVELY. LES LONGUEURS HORIZONTALES MINIMALE ET MAXIMALE SONT 10 POUCES ET 20 PIEDS

RESPECTIVEMENT.

WOLF STEEL LTD, BARRIE, ON, CANADA

1. Install the 5" diameter ﬂ ex pipe

to the ﬁ replace. Secure with 3

screws and ﬂ at washers. Seal

the joint and screw holes using

high temp sealant

(not supplied) or Red

RTV Silicone may

also be used in this

location.

2. Install the 8" diam-

eter ﬂ ex pipe to the

ﬁ replace. Attach and

FIGURE 40

seal the joints.

For optimum per-

formance it is recommended that all horizontal runs have a

¼" rise per foot.

GAS INSTALLATION

Proceed once the vent installation is complete.

0-4500FT(0-1370m)

30,000 BTU/h

20,000 BTU/h

#39

REFERENCE #15510

CERTIFIED FOR

CANADA AND

CERTIFIEE POUR

UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE AVEC CET

APPAREIL. UTILISER AVEC LES COUVERTURES ET LES PORTES

VITREES HOMOLOGUEES SEULEMENT AVEC CETTE UNITE.

AVERTISSEMENT:

CONTACT AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE

FABRICANT.

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS. SEE OWNERS

INSTALLATION MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND RESEALING IS

NECESSAR Y AFTER SER VICING THE VENT-AIR INTAKE SYSTEM.

25¼"

L'APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L'ENSEMBLE D'EVACUA TION PROPRE A WOLF

STEEL. REFERER AU MANUEL D'INSTALLATION DE PROPRIETAIRE POUR L'EVACUA TION PRECISE. IL

EST IMPORTANT DE BIEN REINSTALLER ET RESCELLER L'EVENT APRES AVOIR ASSURE LE MAINTIEN

DU SYSTEME DE PRISE D'AIR.

ELECTRICAL RATING / CLASSIFICA TION: 115V, 0.82AMP , 60HZ

OPTIONAL FAN KIT / ENSEMBLE DE VENTILATEUR FACUL TATIF: GZ-550KT

MADE IN CANADA / FABRIQUE AU CANADA

SERIAL NUMBER/NO. DE SERIE:

GD22