Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HotSpring VIGOR Cold Plunge
Summary of Contents for HotSpring VIGOR Cold Plunge
- Page 1 VIGOR 2025 Cold Plunge Owner’s Manual...
- Page 2 115V System Owner's Record Locating the Cold Plunge Serial Number: ™ The Vigor serial number label is located inside the equipment compartment. Equipment compartment access panel can be found on page 7. You will need the cold plunge model and serial number to properly register your cold plunge and activate coverage.
-
Page 3: Table Of Contents
TABLE OF CONTENTS CONTENTS START-UP & FILL-UP INSTRUCTIONS POSITION POWER CORD SAFETY INFORMATION POSITION DRAIN TUBE IMPORTANT SAFETY INSTRUCTIONS FILLING COLD PLUNGE WITH WATER IMPORTANT COLD PLUNGE INSTRUCTIONS APPLYING POWER INSTALLATION ADDING START-UP CHEMICALS PLANNING A LOCATION FOR YOUR COLD PLUNGE WATER CHEMISTRY GUIDELINES EQUIPMENT ACCESS COLD PLUNGE MAINTENANCE... -
Page 4: Safety Information
SAFETY INFORMATION IMPORTANT SAFETY DON’T: • Do not allow children to climb onto the INSTRUCTIONS cold plunge cover. READ AND FOLLOW ALL • Do not allow children to have unsupervised access to the cold plunge. INSTRUCTIONS AVOIDING THE RISK OF AVOIDING THE RISK TO ELECTROCUTION CHILDREN... - Page 5 SAFETY INFORMATION DON’T: Wait 30 seconds and then reset the GFCI by pushing the RESET button. • Do not use the cold plunge with the The GFCI power indicator will turn on, equipment compartment door removed. restoring power to the cold plunge. If •...
- Page 6 SAFETY INFORMATION AVOIDING THE RISK OF Increased side effects of medication • The use of drugs, alcohol or medication HYPOTHERMIA before or during cold plunge use may lead Prolonged immersion in cold water can result in to unconsciousness with the possibility of HYPOTHERMIA, a dangerous condition which drowning.
-
Page 7: Safety Sign
SAFETY INFORMATION DON’T: • Pregnant or possibly pregnant women should limit cold plunge water • Do not leave the cold plunge exposed to temperatures to 80°F (26.5°C). Failure the sun without water or the cover in place. to do so using colder temperatures may Exposure to direct sunlight can cause solar result in permanent injury to your baby. -
Page 8: Installation
INSTALLATION PLANNING A LOCATION ventilation. When the cold plunge is in use, small amounts of moisture may also be produced. FOR YOUR COLD PLUNGE This moisture can damage walls and ceiling surfaces over time. Special paint is available to Consider these things when determining where to resist moisture damage. -
Page 9: Indoor Installation
INSTALLATION BE AWARE: • Water will also accumulate around the cold plunge when exiting, so flooring materials must Damage caused by inadequate or improper provide a good grip when wet. foundation support is not covered by the cold plunge warranty. It is the sole responsibility of the NOTE: Proper drainage is essential to prevent cold plunge owner to provide a proper foundation water from running all over the floor and under the... -
Page 10: Equipment Access
EQUIPMENT ACCESS EQUIPMENT ACCESS PANELS NEED Back Panel Screws Equipment Compartment Door Screws Cold plunge back panel: To access the back panel compartment: • There are 3 screws holding one T-part on each side of cold plunge. • Remove the 6 screws and 2 T-parts from the back Equipment Access Panel Door door. •... -
Page 11: Electrical Requirements
ELECTRICAL REQUIREMENTS ELECTRICAL REQUIREMENT 2. The 115 V model must use the provided 15 foot (4.5 m) GFCI cord and be plugged directly DO NOT POWER THE COLD PLUNGE into a dedicated GFCI grounded circuit wall WITHOUT FIRST FILLING WITH WATER! outlet between 6' (1.8 m) and 10' (3 m) from the cold plunge. -
Page 12: Control Panel Operation
CONTROL PANEL OPERATION INITIAL START-UP MULTI COLOR LED LIGHT When the cold plunge is first powered up the There are two different light modes which can control system begins a 2 second Startup Mode. be set within the first 5 minutes of power-up by Once Startup Mode completes, the actual water holding the Light button for 8 seconds (until... -
Page 13: System & Panel Version
CONTROL PANEL OPERATION SYSTEM & PANEL VERSION LOCKING PROTECTION When the system is powered on, press the The locking screen or Child lock protection screen allows you to prevent anyone from using the Program Mode button control panel to change several times in a row to current settings. -
Page 14: Diagnostic Lcd Message
CONTROL PANEL OPERATION DIAGNOSTIC LCD MESSAGE Message Meaning Action Required No message on display. The control panel will be disabled until power Power has been cut off to the cold returns. Cold plunge settings will be preserved plunge. Check and reset GFCI on until next power up. -
Page 15: Start-Up & Fill-Up Instructions
START-UP & FILL-UP INSTRUCTIONS IMPORTANT: BECAUSE OF SHIPPING The following procedures should be followed on ORIENTATION, WAIT 24 HOURS TO FILL initial startup and whenever the cold plunge is AND START YOUR COLD PLUNGE ONCE IT drained for routine maintenance. IS IN PLACE FOR INITIAL STARTUP! FILLING THE COLD POSITION POWER CORD... -
Page 16: Applying Power
FILL-UP AND START-UP INSTRUCTIONS APPLYING POWER 3. Once powered up, if E03 message is visible on the control panel there is an air lock in the 1. Turn power to cold plunge "ON" by plugging circulation pump. Disconnect power, and turn GFCI into the wall outlet. -
Page 17: Cold Plunge Component Operation
ADDING START-UP CHEMICALS WATER CHEMISTRY and can damage the heating system. To increase pH, use a pH Up/Increaser (sodium GUIDELINES hydrogen carbonate). Any pH Up or Down should be added one teaspoon at a time, Cold plunge water chemistry is ultimately the waiting one-half hour between application responsibility of the cold plunge owner. -
Page 18: Cold Plunge Maintenance
COLD PLUNGE MAINTENANCE FILTER CARTRIDGE • Rinse cartridge using a garden hose. Rotate and separate filter pleats while spraying water MAINTENANCE to remove all dirt and debris possible. Let filter dry and look for calcium deposits (scaling) or Every month, the filter cartridge should be an oil film. -
Page 19: Surface Care
COLD PLUNGE MAINTENANCE SURFACE CARE COLD PLUNGE LED Do not use solvents or abrasive cleaners to clean REPLACEMENT the cold plunge. Typically, a mild detergent and • Turn OFF the power to the cold plunge water will resolve cleaning issues. (unplug). -
Page 20: Uv Maintenance
COLD PLUNGE MAINTENANCE UV MAINTENANCE e. Slowly remove boot cover (18) and UV-C The Ultraviolet System will require maintenance in lamp (20) from quartz order to help keep your water clean. The following tube (6). maintenance schedule is recommended: Replace new UV-C lamp •... -
Page 21: Draining Or Winterizing
DRAINING OR WINTERIZING WINTERIZING YOUR COLD Every three to six months, depending upon the water condition, you need to renew your water. PLUNGE CAUTION: READ THIS BEFORE DRAINING If you plan to store your cold plunge for the winter, YOUR COLD PLUNGE! •... -
Page 22: Gfci Tripping
TROUBLESHOOTING GUIDE COLD PLUNGE NOT In the event the cold plunge is not working the way it should, please first review all the installation and HEATING OR COOLING operating instructions in this manual and check the message on the panel display. If you are still not Should you notice the cold plunge is not heating satisfied it is working properly, please follow the or cooling while power is still available check the... - Page 24 1280 Park Center Drive Vista, California 92081 (888) 961-7727 ©2024 WATKINS WELLNESS. 300741.25 A (12/24)
Need help?
Do you have a question about the VIGOR Cold Plunge and is the answer not in the manual?
Questions and answers