Pelpro PP60 Owner's Manual

Pelpro PP60 Owner's Manual

Pelpro pp60 pellet stove owner's manual
Hide thumbs Also See for PP60:
Table of Contents

Advertisement

INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
PP60 Pellet Stove
Model(s):
SAFETY NOTICE: PLEASE READ THIS ENTIRE MANUAL
BEFORE INSTALLATION AND USE OF THIS PELLET FUEL-
BURNING ROOM HEATER. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR EVEN DEATH. CONTACT LOCAL BUILD-
ING OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION
INSPECTION REQUIREMENTS IN YOUR AREA.
Questions, problems, missing parts?
Before returning to your retailer, call our
customer service department at 877-427-3316.
This heater meets the U.S. Environmental Protection Agency's emission limits for wood heaters sold after July 1, 1990.
1
Owner's Manual
Installation & Operation
NOTICE: DO NOT DISCARD THIS MANUAL
PP60
7083-171B • July 23, 2013
WARNING
If the information in these instruc-
tions is not followed exactly, a fire
may result causing property dam-
age, personal injury, or death.
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
• Do not overfire - If heater or chimney con-
nector glows, you are overfiring. Overfiring
will void your warranty.
• Comply with all minimum clearances to
combustibles as specified. Failure to com-
ply may cause house fire.
WARNING
Hot glass will cause burns.
Do not touch glass until it is cooled
NEVER allow children to touch glass
Keep children away
CAREFULLY SUPERVISE children in same room as
fireplace.
Alert children and adults to hazards of high temperatures
High temperatures may ignite clothing or other
flammable materials.
Keep clothing, furniture, draperies and other flammable
materials away.
To obtain a French translation of this manual, please contact
your dealer or visit www.pelprostoves.com
Pour obtenir une traduction française de ce manuel, s'il vous
plaît contacter votre revendeur ou visitez www.pelprostoves.com
HOT SURFACES!
Glass and other surfaces are hot
during operation AND cool down.
NOTE
(877) 427- 3316

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PP60 and is the answer not in the manual?

Questions and answers

Summary of Contents for Pelpro PP60

  • Page 1 OWNER: Retain this manual for future reference. NOTICE: DO NOT DISCARD THIS MANUAL WARNING If the information in these instruc- tions is not followed exactly, a fire may result causing property dam- PP60 Pellet Stove age, personal injury, or death. Model(s): • Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of PP60 this or any other appliance.
  • Page 2 RELEASED QUICK START GUIDE 11.75 TOOLING ITEM PART NUMBER PART NAME *Before you plug in this appliance, follow these instructions* Operation / Opération / Operación Maintenance / Entretien / Mantenimiento Daily / Quotidien / Todos los días 1 Bag / 1 Sac / 1 Bolsa Turn Dial Control to OFF. 2.81 4X R0.13 Add pellets to hopper and close Automatic Mode * Priming Fuel...
  • Page 3: Table Of Contents

    Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. • NOTICE: Indicates practices which may cause damage to the appliance or to property. TABLE OF CONTENTS Listing and Code Approvals Getting Started A. Appliance Certification ............5 A. Design, Installation & Location Considerations ......21 B. Mobile Home Approved ............5 B. Draft ................21 C. Glass Specifications ............5 C. Negative Pressure .............21 D. Electrical Rating (On High) ..........5 D. Locating Your Appliance & Chimney .........22 E. BTU & Efficiency Specifications........5 E. Inspect Appliance & Components ........22 General Information F. Tools And Supplies Needed ..........22 Dimensions and Clearances A. Fire Safety .................6...
  • Page 4 CAUTION IMPORTANT It is highly recommended that the pellet heater After reading these instructions, if you have any doubt about your ability to complete your installation in a pro- and chimney be installed by a qualified installer. A fessional manner you should obtain the services of an qualified installer is a person or entity who regularly installer versed in all aspects as to the correct and safe installs solid burning fuel products and chimneys in installation. Do not use temporary makeshift compro- the course of their ordinary business.
  • Page 5: Listing And Code Approvals

    Listing and Code Approvals A. Appliance Certification E. BTU & Efficiency Specifications *BTU input will vary, depending on the brand of fuel you use Series: PP60 in your stove.**Heating capacity depends on climate zone, structure layout, insulation, windows, etc. Laboratory: Intertek Report No. 10072262PRT-001 Type: Solid Fuel Room Heater/Pellet MODEL: PP60 Fuel Burning Type Particulate Emissions 0.34 grams / hr Standard: ASTM E1509-04 and ULC S627- Rating: 00, Room Heater Pellet Fuel *BTU Input: 11,000 - 35,000 / hr Burning type and (UM) 84-HUD, Efficiency: Mobile Home Approved. **Heating Capacity: 750 to 1450 sq. ft. depending...
  • Page 6: General Information

    General Information A. Fire Safety Fuel Material and Fuel Storage (Cont’d) To provide reasonable fire safety, the following should be Lower Ash Content Material given serious consideration: • Most softwoods • Install at least one smoke detector on each floor of your • Fuels with low mineral content home. • Most premium grade pellets • Install at least one carbon monoxide detector on each floor Clinkers of your home. Minerals and other non-combustible materials such as sand • Locate smoke detector away from the heating appliance will turn into a hard, glass-like substance called a clinker when and close to the sleeping areas. heated in the firepot. • Follow the smoke detector manufacturer’s placement and Trees from different areas will vary in mineral content. That installation instructions and maintain regularly.
  • Page 7: General Operating Information

    Operation / Opération / Operación Maint Daily / Quotidien / Tod General Operating Information 2.81 4X R0.13 Automatic Mode * Priming Fuel Minimum / Maximum ** mode Automatique carburant d'amorçage minimale / maximale A. User Dial Control Modo Automático cebado de combustible mínimo / máximo The appliance has one dial control located on the side of the unit used for daily operation. There are four primary...
  • Page 8: C. Priming The Feed Tube 7

    F. Starting Your First Fire C. Priming the Feed Tube (Cont’d) A FIREPOT THAT IS MORE THAN HALF FULL IS OVER- 1) Turn the dial control to “OFF”. FILLED. DO NOT OVERFILL FIREPOT FOR IGNITION. 2) Make sure the firepot is clean, inplace, and free of If there are excessive pellets in the firepot the starts will debris. be extremely smokey and cause an unstable ignition that 3) Plug the unit into the wall and fill the hopper with includes but not limited to rumbling and whistling.
  • Page 9: Your Pellet Appliance - General Operating Parts

    WARNING HOT SURFACES! Glass and other surfaces are hot during operation AND cool down. Hot glass will cause burns. • DO NOT touch glass until it is cooled • NEVER allow children to touch glass • Keep children away • CAREFULLY SUPERVISE children in same room as appliance. • Alert children and adults to hazards of high temperatures. High temperatures may ignite clothing or other flammable materials. • Keep clothing, furniture, draperies and other flammable materials away. NOTICE: If you expect that children may come into contact with this appliance, we recom- mend a barrier such as a decorative screen. See your retailer for suggestions. H. Your Pellet Appliance - General Operating Parts Hopper Lid Switch Dial Control Drop Tube...
  • Page 10: Led Color Coding Chart And Explanation

    I. LED Color Coding Chart and Explanation Number of Description Notes Color Flashes between pauses Green Steady ON while Feed Motor is running continuously. When priming the feed system and filling priming feed tube (This primes the feed tube). the firepot, DO NOT OVERFILL FIREPOT (max time 2 min- FOR IGNITION The unit will automatically utes) go into start up following the prime function. Green Steady ON while Room temperature is close to set burning point and burning on lowest burnt rate. Green Unit is off and ready. To start appliance, follow start up sequence. During shut down, the blowers will shut off Green Appliance is in the start up/ignition...
  • Page 11: Ignition Cycles

    J. Ignition Cycles M. Clear Space 1. At the beginning of each ignition cycle, it is normal to see WARNING! RISK OF FIRE! Do NOT place combustible some smoke in the firebox. The smoke will stop once objects in front or to the sides of the appliance. High tem- the fire starts. peratures may ignite clothing, furniture or draperies. 2. The convection blower will automatically turn on after Mantel: Avoid placing candles and other heat-sensitive your appliance has been burning for approximately 10 objects on mantel or hearth. Heat may damage these minutes.
  • Page 12: Maintaining & Servicing The Appliance

    Maintaining & Servicing the Appliance A. Proper Shutdown Procedure C. General Maintenance 1. Types of Fuel CAUTION The type of fuel you are burning will dictate how often you have to clean your firepot. Shock and Smoke Hazard If the fuel you are burning has a high dirt or ash content, it • Turn dial control to OFF, let appliance complete- may be necessary to clean the firepot more than once a day. ly cool and exhaust blower must be off. Now you can unplug appliance before servicing. Poor quality fuel will cause clinkers to form in the firepot. A clinker is formed when dirt, ash or a non-burnable substance • Smoke spillage into room can occur if appliance is not cool before unplugging. is heated to 2000°F (1093°C) and becomes glass-like. See section D following for more details on fuels with high ash • Risk of shock if appliance not unplugged before content. servicing appliance. Follow the detailed instructions found in this section for each step listed as referenced in the chart below.
  • Page 13 2. Cleaning Firepot with the Firepot Clean-Out Tool; 3. Ash Removal from Firebox • Frequency: Daily or more often as needed • Frequency: Weekly or more frequently depending on • By: Homeowner ash build-up. • By: Homeowner a. The appliance must be in complete shutdown and cool a. There must not be any hot ashes in the firebox during and the exhaust blower off. If you are just cleaning the cleaning so allow the appliance to completely cool. The firepot, there is no need to unplug the appliance. firebox ash should be removed every time the exhaust b. Open the front door of the appliance and lift out the path is cleaned. Frequent cleaning of the ash in the firepot. Use the firepot cleaning tool to break up firebox will help slow down the build-up of ash in the deposits inside the firepot and dispose in an approved...
  • Page 14 6. Cleaning the Glass 8. Cleaning the Exhaust Path, Baffles & Drop Tube • Frequency: Monthly or every 25 bags or more fre- • Frequency: When clear view of the firepot becomes quently depending on ash build-up. obscure • By: Homeowner • By: Homeowner a. Appliance must be completely cool. a. Appliance must be completely cool before cleaning glass. b. Open the door and remove the center baffle first and then the right and left baffles. Thoroughly vacuum the b. Vacuum fly ash from glass and door rope. exhaust path and drop tube and continue throughout c. Use a damp paper towel or any non-abrasive glass the rest of the firebox. Also vacuum the front and cleaner. Wipe off with dry towel.
  • Page 15 10. Cleaning Convection Blower - Requires No Lubrication • Frequency: Monthly depending on Dust/Dirt build-up • By: Homeowner or Qualified Service Technician a. Be sure the appliance is allowed to cool and has been unplugged. b. Remove the right side panel. c. Sweep or vacuum out any build-up on the impellers. Use a brush or compressed air to loosen dirt if needed. Avoid damaging the impellers. 12. Preparing Firebox for Non-Burn Season • Frequency: Yearly • By: Homeowner a. Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off. b. Remove all ash from the firebox and vacuum thoroughly. c. Paint all exposed steel, including cast-iron. • Purchase high temperature paint from your local retailer. • Must use a high-temperature paint made specifi- cally for heating appliances. 11. Cleaning Exhaust Blower - Requires No 13.
  • Page 16: High Ash Fuel Content Maintenance

    D. High Ash Fuel Content Maintenance • Frequency: As needed • By: Homeowner Poor quality pellet fuel, lack of maintenance, or if the small dial control is set to a less than optimum setting, poor com- bustion conditions that make the firepot fill quickly with ashes and clinkers. This condition makes the appliance susceptible to overfilling the firepot with pellets which may result in smoking, soot- ing and possible hopper fires. The figure below shows an example where the firepot overfills, pellets back up into the feed tube and ash has accumulated in the firebox. An inefficient and non-economical method of burning of fuel caused by poor quality pellet fuel is shown below. If the ash buildup exceeds the half way point in the firepot IMMEDIATE ATTENTION AND CLEANING IS REQUIRED.
  • Page 17: Frequently Asked Questions

    E. Frequently Asked Questions What causes my glass to become dirty? Why is there a black residue building up on the If the glass has white ash build up it is normal and the outside of my home? glass should be cleaned. If it is a black soot build up Wind can cause this to happen. If the appliance is airflow thru the unit may be restricted. The most often operating correctly very little soot should ever exit the cause is overdue maintenance and cleaning. See termination cap. Also check to be sure the venting is “Maintaining and Servicing Appliance” in the owner’s installed per the owner’s manual and local codes. manual and/or make adjustments to the trim control. Do I need an outside air kit? How can I get more heat out of the appliance? Outside air is required for mobile home installs and in The most often cause of diminished heat output is...
  • Page 18: Replacement Parts

    Replacement Parts B. Exhaust Blower Replacement A. Convection Blower Replacement 1. Turn the dial control to the off position. Unplug the power 1. Turn the dial control to the off position. Unplug the power to the unit. to the unit. 2. The convection blower is located in the rear of the unit. 2. Remove the left side panel by loosening the two or three bolts in the rear of the unit. 3. Using #2 Phillips screwdriver, loosen the bolts on the rear of the unit holding on the side panels. You do not 3. Disconnect 2 white wires from the white and blue wires of need to remove the screws. Remove side panels by the exhaust blower.
  • Page 19: Snap Disc Replacement

    D. Igniter Replacement C. Snap Disc Replacement 1. Turn the dial control to the off position. Unplug the Power - Manual Reset power to the unit. 1. Turn the dial control to the off position. Unplug the power 2. Unplug the wire leads to the igniter. to the unit. 3. Remove the screw in the side of the igniter chamber. 2. Using #2 Phillips screwdriver, loosen the bolts on the rear Pinch the ends of the bracket together and pull the of the unit holding on the left side panel. You do not need igniter straight out of the igniter chamber. to remove the screws. Remove side panels by lifting up and out. 4. If there is difficulty in removing the igniter from the chamber, the chamber can be removed from the rear 3. Locate the snap disk on the top side of the feed tube of the firebox by removing the 1/4-20 bolt.
  • Page 20: Glass Replacement

    F. Glass Replacement I. Feed Motor Replacement 1. Open the door from the appliance by lifting door off of hinge 1. Turn the dial control to the off position and unplug the unit. pins and lay on a flat surface face down. Remove the right side panel and feed motor cover plate in the rear of the unit. 2. Using a Phillips Head screw driver, remove the 3 brackets and set aside. 2. Unplug the connector from the feed motor. 3. Remove old glass and replace with the new glass. 3. Using pliers, remove the cotter pin. 4. Re-install the brackets using the same screws. 4. Remove the feed motor from the feed shaft. 5. Reinstall the new feed motor by aligning the clearance WARNING hole in the feed motor shaft with the auger spring shaft. 6. Plug the feed motor leads back in and restore power. • Glass is 5mm thick high temperature heat- resistant ceramic glass.
  • Page 21: Getting Started

    If you have a lower reading than you find on the and exhaust equipment chart, your stove does not have adequate draft to burn the • Ensure furnace and air conditioning return vents are not fuel properly. located in the immediate vicinity of the appliance • Avoid installing the appliance near doors, walkways or Minimum Vacuum small isolated spaces MODEL Requirements • Recessed lighting should be a “sealed can” design PP60 0.17 inches W.C. • Attic hatches weather stripped or sealed • Attic mounted duct work and air handler joints and seams taped or sealed www.pelprostoves.com 7083-171B • July 23, 2013...
  • Page 22: Locating Your Appliance & Chimney

    D. Locating Your Appliance & Chimney F. Tools And Supplies Needed Location of the appliance and chimney will affect performance. Tools and building supplies normally required • Install through the warm airspace enclosed by the building for installation, unless installing into an existing envelope. This helps to produce more draft, especially masonry fireplace: during lighting and die-down of the fire. Reciprocating Saw Gloves • Penetrate the highest part of the roof. This minimizes the Channel Locks Safety Glasses...
  • Page 23: Dimensions And Clearances

    Dimensions and Clearances B. Clearances to Combustibles (UL and ULC) MODEL: PP60 A. Appliance Dimensions 21-3/4 [552] 3-1/2 [89] 21-15/16 [558] Vertical Installations (Interior Flue) Straight Back Against Wall Inches Millimeters Back Wall to Appliance Side Wall to Appliance Corner Installation Inches Millimeters Walls to Appliance Horizontal Flue Installations...
  • Page 24: Hearth Pad Requirements (Ul And Ulc)

    C. Hearth Pad Requirements (UL and ULC) Use a non-combustible floor protector, extending beneath appliance and to the front, sides and rear as indicated. Measure front distance “M” from the surface of the glass door. Must extend 2 inches (51mm) beyond each side of pipe (shaded area) *C: Exception for Horizontal Installations: USA Hearth Pad Requirements CANADA INSTALLATIONS: A non combustible floor pro-...
  • Page 25: Vent Information

    Vent Information B. Venting Termination Requirements A. Chimney and Exhaust Connection CAUTION Chimney & Connector: Use 3 or 4 inch (76-102mm) Do not terminate vent in any enclosed or semi-enclosed diameter type "L" or "PL" venting system. It can be vented area such as a carport, garage, attic, crawl space, under a vertically or horizontally. sun deck or porch, narrow walkway or closely fenced area, or any location that can build up a concentration of fumes 2. Mobile Home: Approved for all Listed pellet vent. If using such as a stairwell, covered breezeway, etc. the 3 inch (76mm) vertical Top Vent Adapter Kit or the 3 to 6 inch (76-152mm) Top Vent Offset Adapter, use Listed . Termination must exhaust above air inlet elevation. It is double wall flue connector. An authorized Outside Air Kit strongly recommended that at least 60 inches (1.5m) must be used with manufactured home installations.
  • Page 26: Pellet Venting Charts

    C. Pellet Venting Charts WARNING The maximum horizontal venting allowed with no vertical vent- ing attached is 48 inches (1219mm) including one 90° elbow Fire Risk. or two 45° elbows. This is our recommended horizontal vent- • Only LISTED venting components may be ing installation. Addition of any horizontal venting beyond 48 used. inches (1219mm) requires a minimum 60 inches (1524mm) of • NO OTHER vent components may be used. additional vertical vent. Horizontal sections of vent pipe should Substitute or damaged vent components may have a 1/4 inch (6.35mm) rise per foot.
  • Page 27: Venting Systems

    Venting Systems A. Vertical - Interior - Typical Installation C. Vertical into Existing Class A Chimney PREFERRED METHOD #1 Rain Cap Rain Cap Flashing 12 in. (305mm) Minimum Flashing 12 in. (305mm) Minimum Firestop Firestop 6 in. (152mm) Class A Chimney Connector Adapter Ceiling Support...
  • Page 28: Masonry

    WARNING WARNING Fire Risk Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer Inspection of Chimney: to the owner’s information manual provided with this appli- • Masonry chimney must be in good condition. ance. For assistance or additional information consult a • Meets minimum standard of NFPA 211 qualified installer, service agency or your dealer. • Factory-built chimney must be minimum 6 inch (152mm) UL103 HT. D. Masonry Fireclay flue Concrete Cap Liner with Airspace Flashing 1 in. (25mm) Clearance with Firestop 1 in. (25mm) Clearance 3 in. (76mm) Minimum 6 in.
  • Page 29: Through The Wall

    F. Through The Wall Horizontal termination cap must be a minimum of 6 inches. (152mm) from the wall. Approved for mobile home instal- lations. Must use 3 or 4 inch (76-102mm) “L” or “PL” listed In Canada, where passage through a wall or parti- pellet venting or Listed double wall pipe and an authorized tion of combustible construction is desired, the Outside Air Kit in mobile homes. installation shall conform to CAN/CSA-B365 NOTICE: CAUTION DO NOT DOWNWARD VENT. Please note that while the minimum clearance for the The following will occur: termination cap is 6 inches (152mm) there is the pos- • The appliance will not vent properly sibly of soot build-up around the termination area. If this • Smoke spillage in the house...
  • Page 30: Mobile Home

    Mobile Home CAUTION A. Mobile Home Installation THE STRUCTURAL INTEGRITY OF THE MOBILE HOME You must use an authorized Outside Air Kit FLOOR, WALL AND CEILING/ROOF MUST BE MAIN- for installation in a mobile home. TAINED Do NOT cut through: 1. An outside air inlet must be provided for the combustion • Floor joist, wall, studs or ceiling trusses. air and must remain clear of leaves, debris, ice and/or • Any supporting material that would affect the structural snow. It must be unrestricted while the appliance is in integrity. use to prevent room air starvation which causes smoke spillage. Smoke spillage can also set off smoke alarms. 2. The combustion air duct system must be made of metal. CAUTION It must permit zero clearance to combustible construc- tion and prevent material from dropping into the inlet or Never draw outside combustion air from: into the area beneath the dwelling and contain a rodent...
  • Page 31: Appliance Set-Up

    Appliance Set-Up A. Outside Air Kit Instructions CAUTION An outside air kit has been provide standard with the appli- Never draw outside combustion air from: ance. It is highly recommended to use the outside air kit for • Wall, floor or ceiling cavity maximum performance and to reduce effects from negative • “Enclosed space such as an attic, garage or pressure in the home. crawl space. For attachment to this platform, knock out the rectangular B. Power up the Unit plate in the rear of the unit and slide the tube in the rear of the unit. Using the hose clamp, attach the flex pipe to the 2” Plug the unit into 120VAC power. tube welded to the rear of the firebox as shown in the photo. CAUTION Shock hazard. • Do NOT remove grounding prong from plug. • Plug directly into properly grounded 3 prong receptacle.
  • Page 32: Troubleshooting

    Troubleshooting Symptom Possible Cause Corrective Action Plug in appliance - No No Power to outlet. Check circuit breaker at service panel. response. 5 amp fuse defective or blown Replace fuse. Snap disc tripped or defective. Reset or replace snap disc. Unit Will Not Light No Fuel Out of fuel. Check hopper. Fill with fuel. Vacuum switch not closing, no vacuum. Check exhaust blower is plugged in and operating. Check vacuum switch is plugged in Check vacuum hose is in good condition clear and connected at both ends Make sure venting system is clean Make sure front door is closed Check vacuum switch fitting on side of feed tube for blockage Hopper lid open. Close Hopper Lid Defective hopper switch. Check hopper switch operation Feed System is Jammed Inspect and unjam the feed assembly Feed motor not plugged in Reconnect feed motor No Igniter Igniter not plugged in Plug the igniter in Igniter not centered Center the igniter Igniter seated in chamber completely Igniter defective Replace igniter...
  • Page 33 Symptom Possible Cause Corrective Action Slow or smoky start-up Dirty exhaust and/or venting system. Check for ash build up in unit, including behind rear and/or lazy flame panels, firebox, exhaust blower and venting. Not enough combustion air Adjust the trim Misaligned igniter Center the igniter in the chamber Wet fuel / poor quality fuel Replace fuel Convection blower fails Convection Blower to start. Jammed Inspect, clean, and un-jam the blower. Not plugged in Plug the blower in Replace blower Exhaust probe Not sensing correct temperature Clean the exhaust outlet especially the right side. Control box is defective. Replace control box. Exhaust blower fails to Exhaust Blower start Jammed Inspect, clean, and un-jam the blower. Not plugged in Plug the blower in Replace blower Control board is defective. Replace control board. Convection Blower Does Convection blower short circuit. The fuse will Inspect wires, blowers, and power cord to find cause Not Turn Off...
  • Page 34 Following correction of any Alarm, turn the dial control to the OFF position, wait 10 seconds and turn back to desired setting OR unplug the unit, wait 10 seconds then restore power. Alarm Possible Cause Corrective Action (LED Flashing RED) 1 Flash: Empty Hopper No fuel is delivered to the firepot to sustain flame Fill the hopper, inspect the feed tube for jams, inspect Hopper empty (most likely)
  • Page 35: Reference Materials

    Reference Materials A. Component Function 1. Control Board When describing the location of a component, The control board is located on the right side of the appliance it is always AS YOU FACE THE FRONT OF THE behind the lower right side panel. APPLIANCE. 2. Convection Blower Snap Disc (Back Burn Protector) 200°F The convection blower is mounted in the rear of the unit. It pushes air up the rear of the firebox, across the top and out Snap disc is mounted on the back of the auger tube in the the front. As the air moves past the firebox it is heated.
  • Page 36: Wiring Diagram

    B. Wiring Diagram IGNITER VACUUM HOPPER FEED MOTOR SWITCH SWITCH EXHAUST BLOWER CONVECTION BLOWER NEUTRAL 110 V LINE SNAP DISC FUSE EXHAUST TEMPERATURE AMBIENT TEMPERATURE SERIAL PORT (SERVICE ONLY) POT SET TEMP VCC POT SET TEMP GND POT SET TEMP SIG POT FEED ADJUST VCC POT FEED ADJUST GND POT FEED ADJUTS SIG...
  • Page 37: Replacement Parts

    C. Replacement Parts 15.2 15.1 ITEM DESCRIPTION COMMENTS PART NUMBER STOCKED at DEPOT HOPPER LID ASSEMBLY SRV7083-019 SIDE CURTAIN LEFT HAND SRV7083-154 DOOR ASSEMBLY SRV7083-021 3.1 GLASS ASSEMBLY SRV7081-173 3.2 ROPE, DOOR, 3/4” X 84” 832-1680 3.3 HINGE PIN QTY: 2 433-1590/2 3.4 THREADED HINDLE ASSEMBLY KIT KS-5140-1448 3.5 HANDLE BLACK PHENOLIC KIT KS-5140-1442 BAFFLE KIT SRV7079-006 FIREPOT SRV7077-003 CONTROL BOARD SRV7079-050 CONVECTION BLOWER SRV7000-659 IGNITER KIT...
  • Page 38: Service & Maintenance Log

    D. Service & Maintenance Log Date of Service Performed By Description of Service 7083-171B • July 23, 2013 (877) 427- 3316...
  • Page 39: Warranty

    E. Warranty Hearth & Home Technologies, Inc. PELPRO LIMITED WARRANTY Hearth & Home Technologies Inc., on behalf of its hearth brands (“HHT”), extends the following warranty for PELPRO wood and pellet hearth appliances that are purchased from an HHT authorized dealer. WARRANTY COVERAGE: If an inspection by the dealer indicates that a limited warranty claim is justified, and all conditions of this limited warranty have been met, the manufacturer's total responsibilities and liabilities shall be to repair or replace, at the manufacturer's option, the...
  • Page 40 CONTACT INFORMATION: 1445 North Highway Colville, WA 99114 Please contact the Hearth & Home Technical Group with any questions or concerns. www.pelprostoves.com For Customer Service 1-877-447-3316 Prior to calling, please have the model, serial number, and sales receipt of the unit you are calling about. This information can be found at the rear of the unit.

Table of Contents

Save PDF