Fuel Range Selection; Starting Fire And Electric Ignite Screens - Cumberland Stove Works MF3800 Operator's Manual

lighter, close the door and press ON key. The sound
you hear after the ON key is pushed is the exhaust fan
running. After the ON key is pressed the control will read
as follows:
STARTINg FIRE
LEVEL 1
eLeCtriC ignition inStruCtionS
(MF3800 only)
After the Range has been loaded the controller will then
read as follows
ELECTRIC IgNITE
yes
no
IMPORTANT: Before lighting the stove for the first time,
make sure that no shipping items have been left inside the
firebox or ash pan.
When initially filling an empty hopper you must prime the
feed auger. To prime the auger press the ADD FUEL button.
This will turn the auger on for one minute or until the ADD
FUEL button is pressed again. Run the feed auger until
you see fuel start to drop into the firepot.
Note: The parlor stove has been designed with a safety
switch on the hopper lid. The auger will not run with the
hopper door open.
Once the auger is primed pressing ENTER will start the
electronic ignition sequence. Note: Pre loading the firepot
isn't necessary for electric ignition; the program is designed
to automatically load the firepot. The noises you will hear
during electric ignition are the combustion fan and air pump
running. The screen will read as follows:
ELECTRIC IgNITE
LEVEL 1
Starting Fire anD eLeCtriC ignite
SCreenS
(MF3800 only)
The starting fire and electric ignition sequences have
been designed to take a cold stove up to normal operating
temperature. These are preset feed rates and fans speeds
set by CSW to ensure the ignition of multiple types of
fuels.
800-345-6007
During starting fire and electric ignition sequences you
may change the level by pressing the TEMP UP or TEMP
DOWN buttons.
During starting fire and electric ignition sequences you may
choose to run your stove thermostatically by pressing the
THERMOSTAT ON/OFF button. See Thermostatic Control
Operation.
At any time you may add more fuel to the firepot by pressing
the ADD FUEL button. Note: the feed auger will stay on
for one minute or until the ADD FUEL button is pressed
again.
During starting fire and electric ignition sequences the
convection fan (the fan that circulates warm air throughout
room) will start once stove has reached 110 degrees. To
control convection fan speed use Fan Up and Fan Down
buttons (Buttons 3 and 8 in Figure 22). Note: Hot stoves
need air circulating through them at all times to prevent
overheating the electronic controls. Therefore, once proof
of fire is made the convection fan will continue to run.
After the stove runs it's starting fire or electric ignition
sequences the controller will read RANGE -4 (will display
chosen fuel range) LEVEL -6 (will display chosen heat
output level). This is the normal operating screens for the
MF series parlor stove.
normaL oPeration
During normal manual operation of the stove the controller
will read as follows:
TEMP 72
RANGE 1-4 LEVEL 1-6
At any time during normal operation you will be able to
change the Fuel Range by pressing the SCROLL button.
(MF 3800 only) At any time during normal operation you will
be able to run the igniter by pressing the SCROLL button
during the normal operating
At anytime during normal operation you may change the
heat level by pressing the TEMP UP or TEMP DOWN
buttons. Note: if the stove is being controlled by the local
thermostat the TEMP UP and TEMP DOWN buttons control
the thermostat setpoint. If the stove is being controlled
by the remote thermostat the TEMP UP or TEMP DOWN
buttons have no effect on the heat output.
At anytime during normal operation you may turn on or off
the thermostatic control by pressing the THERMOSTAT
ON/OFF button.
CumberlandStoveWorks.com
INSTALLATION AND OPERATION MANUAL
MF3700, MF3800 Models
Page 7