Operating Instructions; Becoming Familiar With Your Tri-X Controller Key Pad; When You Are Ready To Use Your Stove; Fuel Range Selection - Cumberland Stove Works MF3800 Operation And Maintenance Manual

OperatiOn
BecOMinG FaMiLiar WitH YOUr
tri-x cOntrOLLer keY pad
1 3
2 4
expLaininG tHe tri-x cOntrOLLer keY pad
1: On Switch – Starts Stove Operation When Instructed.
2: Off Switch – Turns Off Stove Operation at Anytime
3: temperature Up control – Controls heat levels 1 - 6
4: temperature down control - Controls heat levels 1 - 6
5: Fan Up control – Makes room fan go faster
6: Fan down control – Makes room fan go slower
7: add Fuel control – Turns Auger on for 1 minute
8: thermostat On / Off – Turns On / Off Thermostat
Options
9: Scroll – Changes heat Ranges / Reignition
10: enter – Chooses the Top Selection on the Screen
11: display Screen

WHen YOU are readY tO USe YOUr StOVe:

iMPORTaNT: Before filling the hopper, make sure all shipping
and packaging items are removed from the hopper and there
are no obstructions in the auger housing opening.
Fill the hopper with a bag of approved solid fuel and close the lid.
Upon plugging in the power supply cord, your stove will begin
power-up. With the stove now powered up, the first screen you
will see on the controller is the model and version of software
loaded in the control. The controller will then default to the
Fuel Range Selection Mode on the screen:
RANgE 1
RANgE 2
11
5
7 9
8 10
6
cumberlandStoveWorks.com
OPERATIOn AND MAINTENANCE MANUAL
WarninG
neVer pUt StartinG peLLetS Or BUrn GeL intO tHe
HOpper OF tHe StOVe. tHiS cOULd reSULt in deatH Or
SeriOUS inJUrY and Or prOpertY daMaGe. dOinG SO
WiLL VOid aLL WarrantieS.

FUeL ranGe SeLectiOn

The CSW Multi Fuel Parlor stove has four fuel ranges and six heat
output levels within each fuel range. T his gives the stove 24 levels
of variability maximizing the burn with your chosen fuel. Range
1 Level 1 is the lowest feed rate/combustion airflow and Range 4
Level 6 is the highest feed rate/combustion airflow. See FiGUre 7.
Each range is a group of feed rate options--there are 6 settings
within each group. The feed rate increases with the range and
level. A higher feed rate increases the heat capacity. Increasing
the level increases the speed of the combustion motor and
feed rate. A faster combustion motor speed increases airflow in
the stove, which is beneficial when burning lower quality fuels.
ranGeS FOr apprOVed FUeLS
Corn: 1-2 / Wood Pellets: 2-3-4 / Cherry Pits: 4
Range 4
Range 3
Range 2
1 2 3 4 5 6
Levels 1-6
Range 1
1 2 3 4 5 6
Levels 1-6
Lowest Feed Rate/
Combustion Airflow
Figure 7: Feed rate chart.
SeLectinG tHe ranGe
The control will offer two selections on the screen. To browse
through the range selections use the SCROLL button. To choose
a range, scroll through until the desired range is on top and
press ENTER. nOte: When using the ScrOLL button to
choose a fuel range, the screen will display two options.
pressing enter will always select the top option. Range
may be changed at anytime after the ignition cycle during the
stove operation by pressing the SCROLL button. The screen
will appear as follows:
RANgE 1
RANgE 2
Model MF3800
1 2 3 4 5 6
Levels 1-6
1 2 3 4 5 6
Levels 1-6
Highest Feed Rate/
Combustion Airflow
page 13