Preparing The Remote Control; Rf Remote Control Function (For Vr-6070 Only) - Kenwood VR-6070 Instruction Manual

Setting up the system
.~~~eari!l.!Lt~1!
remote control
~,~"."
..
~,_
..
?t~£'i¥,"4:: ~-.y.-':"""""-"""'.,
... , ,_"'."-"""".-' '.'. '0'
Loading the batteries
o
Remove the cover.
e
Insert the batteries.
Remote control operation
When the STANDBY Indicator is lit. the power turns ON when you press
the POWER c' J or SOURCE c' J key on the remote control When the
power comes ON, press the key you want to operate.
IR Transmitter
E) Close the cover.
• Insert two AA-size IR6) batteries as indicated by the polarity markings
Operating other component range (fR Transmitter)
lk:
~r;;;E12::ir----
I
'
I \
/ I \
6m .
i
"
~
30' ' 30'
Remote sensor
Operating receiver range (RF Transmitter)
RF remote control function
(For VR-6010 only)
~h~~~·ijt"~·"1·,,-),_,-~·'t,-"-'·<.r.,~-,·,-,1-,_<
__ '
The remote control has the RF remote function
In
addition to the IR
remote function. The VR-6070 can receive the remote control com-
mands even when they are installed in a position where the IR remote
signal can hardly access, for example inside a cabinet
-,~,!,%');:~~\Q;'t-''':':='~;,s:.!.;;;,:,~?',; . ... ,,-!,:;,..;-:.,~,:.,.:'.:.\ .....:",..." ... :.: .:'." ':;"~';"'>"- Y'-
.,
Changing the RF transmission frequency
The RF remote function may be unavailable due to radio wave cross talk,
etc, In this case, the transmission frequency can be changed.
I
10m
I
POWER
<0
~'~~~:
, 00001
!
0000'
. 0000
0000 '
~~
'c:oo~~;
RF Remote antenna
, - - - - ' - - - - - - - l
r:
RF Transmitter
To change the RF remote transmission frequency:
o
Change the RF switch setting.
After changing the RF frequency of remote control, be also sure to
change that of the receiver
e
Change the receiver's RF reception frequency.
• Press and hold the SETUP key on the front panel of the receiver
for more than 2 seconds
Each time you press the SETUP key, the RF reception frequency
changes as follows:
0':
"RF REMOTE BAND 1"
[ ®.
"RF REMOTE BAND 2"
:1'
"RF REMOTE OFF"
• Select the same number as the positioll number of the RF
switch of the remote control except for "OFF"
• The remote control signal received by main unit IR and RF signals
• When pressing more than one remote control key successively, press the
keys securely by leaving an interval of 1 second or more between keys
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.
2 When the remote-controllable distance gets shorter than before, re-
place both batteries with new ones.
3, Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause a malfunction
in such a case, change the location of the system installation to pre-
vent malfunction.
Important notes
Here is list of adjustment which can maximize the operation of
your remote control. For optimal operation ofthe remote control:
Aim the remote control toward the room where the receiver IS
located
.i
Do not position the I'eceiver and remote control near metal (such
as heat ducts) Metal can absorb RF signals
Make sure the batteries in the remote control are fully charged
Weak batteries will affect the range of the remote control
When there IS an obstruction around other equipments that send
signal from the remote control, the control distance of the RF
remote signal will be short
Note
• The tests for range limits of the remote control and the receiver are
conducted in open-air distance test. Actual distance of the signal will
be based on the construction of the bUilding where the un,t is being
used in as well as other factors such as outside interfel'ence