For The U.k. Only - Kenwood VR-6070 Instruction Manual

Specifications
For the U.K. only
AUDIO section (KRF-X9060D)
Rated power output during STEREO operation
DIN/IEC (20 Hz - 20 kHz, 0.09% T.H.D. at 6 n)
............................................................................... 100 W + 100 W
Effective power output during SURROUND operation
FRONT (20 Hz - 20 kHz, 0.09% T.H.D. at 6 Q one channel driven)
................................................., 100 W + 100 W
CENTER (20 Hz - 20 kHz, 0.090/0 T.H.D. at 6 n one channel
driven) 100 W
SURROUND (20 Hz - 20 kHz, 0.7% T.H.D. at 6 n one channel
drivenl l00 W + 100 W
SURROUND BACK/SUBWOOFER (20 Hz - 20 kHz, 0.09%
T.H.D. at 6
n
one channel driven) 100 W
Total harmonic distortion 0.009% (1 kHz, 50 W, 6
m
Frequency response
Line
(CD/DVD,
TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
................................................. 10 Hz - 100 kHz, +0 dB - -3.0 dB
PHONO 'RIAA' response 40 Hz - 20 kHz, +1.5 dB - -3.0 dB
Maximum input level
PHONO (MM) .45 mV, 1% T.H.D. at 1 kHz
Signal to noise ratio (IHF'66)
PHONO (MM) 75 dB
Line
(CD/DVD,
TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
............................................................................................... 95 dB
Loudness control
VOLUME at -30 dB level +6 dB (100 Hz)
Input sensitivity
I
impedance
PHONO (MM) 4.0 mV
I
47 k.O
Line
(CD/DVD,
TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)
.............................................................................. 320 mV
I
47 kn
Output level
I
impedance
TAPE REC 320 mV
I
1 kn
PRE OUT (FRONT,CENTER,SURROUND) 1 V
I
500
~2
PRE OUT (SURROUND BACK) 1 V
I
500 n
PRE OUT ISUBWOOFER} 1 V
I
500
n
Tone control
BASS :10 dB (at 100 Hz)
TREBLE :!:10 dB (at 10 kHz)
DIGITAL AUDIO section
Sampling frequency 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
Input level
I
impedance
I
wave length
Optical (-15 dBm - -24 dBm), 660 nm :30 nm
Coaxial 0.5 Vp-p
I
75
n
Output level
I
impedance
I
wave length
Optical (-21 dBm - -15 dBm), 660 nm :!:30 nm
VIDEO section
VIDEO inputs
I
outputs
VIDEO (composite) 1 Vp-p
I
75
Q
S VIDEO inputs loutputs
S VIDEO (luminance signal) 1 Vp-p
I
75
Q
S VIDEO (chrominance signall 0.286 Vp-p
I
75
Q
COMPONENT VIDEO inputs loutputs
COMPONENT VIDEO (luminance signal) 1 Vp-p
I
75
Q
COMPONENT VIDEO (CB/CR-signal) :0.32 Vp-p / 75 Q
FM tuner section
Tuning frequency range 87.5 MHz - 108 MHz
Usable sensitivity
MONO 1.31JV (75 ml 13.2 dBf (40 kHz dev, SIN 26 dB)
STEREO 45 IJV (75 Ql/ 42.1 dBf (40 + 6 kHz dev, SIN 46 dB)
Total harmonic distortion
MONO (1 kHz, 40 kHz dev) 0.2% (65.2 dBf input)
STEREO (1 kHz, 40 + 6 kHz dev) 0.8% (65.2 dBf input)
Signal to noise ratio (DIN weighted at 1 kHz)
MONO 65 dB (65.2 dBf input)
STEREO 60 dB (65.2 dBf input)
Stereo separation (1 kHz) 36 dB
Selectivity (:300 kHz) 64 dB
Frequency response (30 Hz - 15 kHz) +0.5 dB, -3.0 dB
MW tuner section
Tuning frequency range 531 kHz - 1,602 kHz
Usable sensitivity (30% mod, SIN 20 dB) 16IJV
I
(600 IJV/m)
Signal to noise ratio (400 Hz, 30% mod)
.......................................................... 50 dB (60 dBIJ VEMF input)
GENERAL
Power consumption 330 W
AC outlet
SWITCHED (total 90 W max.)
Dimensions W : 440 mm (17-5/16")
H : 159 mm 16-1/4")
D : 392 mm (15-7/16")
Weight (Netl 9.8 kg (21.6Ib)
Notes
1 KENWOOD follows a poliCy of continuous advancements in development For this reason specifications may be changed without notice.
2 Tile full performance may not be exhibited in an extremely cold location (under a water-freezing temperature)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -