Contact Id Event Codes - Honeywell ADEMCO LYNXR Series Installation And Setup Manual

Report 3+1/4+1 Standard
Alarm SSS(S) A
Trouble SSS(S) T
Bypass SSS(S) B
AC Loss SSS(S) E
Low Battery SSS(S) L
Open SSS(S) O
Close SSS(S) C
Test SSS(S) G
Restore Alarm SSS(S) R
AC Restore SSS(S) R A
Low Battery Restore SSS(S) R L
Trouble Restore SSS(S) R T
Bypass Restore SSS(S) R B
ADEMCO Contact ID® Reporting takes the following format: CCCC Q EEE GG ZZZ where:
CCCC = Customer (subscriber) ID
Q = Event qualifier, where: E = new event, and R = restore
EEE = Event code (3 hex digits) (for a complete list of event codes, refer to the central office receiver manual)
GG = Always "00"
ZZZ = Zone/Contact ID® number reporting the alarm, or user number for open/close reports. System
status messages (AC Loss, Walk Test, etc.) contain zeroes in the ZZZ location.
Code
110 Fire Alarm
121 Duress
122 Alarm, 24-hour Silent
123 Alarm, 24-hour Audible
131 Alarm, Perimeter
132 Alarm, Interior
134 Alarm, Entry/Exit
135 Alarm, Day/Night
145 Wireless Dialer Tamper
146 Silent Burglary
150 Alarm, 24-Hour Auxiliary
301 AC Power
338 Wireless Dialer Low Battery
341 Wireless Dialer Tamper
342* Wireless Dialer AC Loss
344 RF Jam Detected
351* Wireless Dialer Phone Line Cut
354 Fail to Report
355 Wireless Dialer Loss of RF Supervision
(plus Zone 93)
355 (Zone 000) Reported by the 5842 Wireless Dialer
373 Fire Loop Trouble
374 Exit Error Alarm
*If supported by the 5842 Wireless Dialer that is installed.
System Communication
3+1/4+1 Expanded
SSS(S) A
AAA(A) Z
SSS(S) T
TTT(T) t
SSS(S) B
BBB(B) b
SSS(S) E
EEE(E) A C
SSS(S) L
LLL(L) L B
SSS(S) O
OOO(O) U
SSS(S) C
CCC(R) U
SSS(S) G
GGG(G)g
SSS(S) R
RRR(R) Z
SSS(S) R A
R A R A R A (R A )A c
SSS(S) R L
R L R L R L (R L )L B
SSS(S) R T
R T R T R T (R T )t
SSS(S) R B
R B R B R B (R B )b
CONTACT ID® EVENT CODES
Definition
(plus Zone 93) (Alarm)
(plus Zone 93)
(plus Zone 93) (Trouble)
(plus Zone 93)
(plus Zone 93)
4+2
SSSS AZ
SSSS Tt
SSSS Bb
SSSS EA C
SSSS LL B
SSSS OU
SSSS CU
SSSS Gg
SSSS RZ
SSSSR A A c
SSSS R L L B
SSSS R T t
SSSS R B b
Code
380 Global Trouble, Trouble Day/Night
381 RF Supervision Trouble
383 RF Sensor Tamper
384 RF Sensor Low Battery
401 Disarmed, Armed AWAY (NO DELAY),
Armed AWAY
403 Scheduled Auto Arm
406 Cancel by User
407 Remote Arm/Disarm (Downloading)
408 Quick Arm AWAY/NO DELAY
441 Disarmed/Armed STAY/NO DELAY, Quick Arm
STAY/NO DELAY
570 Bypass
602 Periodic Test
606 AAV to follow
607 System Test
623 Event Log 80% Full
654 System Inactivity
NOTE: The following codes are logged in the event log upon
occurrence, but are not reported:
305 = System Reset
627 = Keypad Program Mode Entry
–55–
Definition
(Trouble)