Honeywell ADEMCO LYNXR Series Installation And Setup Manual page 20

Data Field Descriptions
15-Second Dialer Delay (Burglary)
✻
50
0 = no dialer delay
1 = provide 15-second delay of burglary alarm report
when armed away
Periodic Test Report
✻
51
0 = no test report
1 = once every 24 hrs
✻ First test Report Offset
52
0 = 24 hrs after exit program mode or download
1 = 6 hours after exit program mode or download
2 = 12 hrs after exit program mode or download
3 = 18 hrs after exit program mode or download
Sescoa/Radionics Select
✻
53
0 = Radionics (0–9, B–F reporting)
1 = SESCOA (0–9 only reporting)
Lack of Usage Notification
✻ 54
0 = Disabled
1 = 1 day
2 = 7 days
3 = 27 days
Note: There will be no local annunciation indicating that
this report has been sent to the Central Station.
✻ RF Jam Detection
58
0 = no jam detection
1 = RF jam detection with event logging, but no
central station report
2 = RF jam detection with event logging and with
central station report (if trouble/restore report is
enabled in fields ✻60, ✻71)
SYSTEM STATUS AND RESTORE REPORT CODES PROGRAMMING (
Program Report Codes using the interactive
✻ ✻ ✻
fields 59- 76, 89. The following is a set of guidelines when programming report codes. The actual report code digits
that you enter depend upon the particular installation, and should be in agreement with you and the central station
office receiving the signals.
With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, A, B, C, D, E, or F. Enter "#+10" for A
(reports a "0" on some receivers), "#+11" for B, "#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F. Entering "0" in the
first box will disable a report. Entering "0" in the second box results in automatic advance to the next field.
With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, or A–F, as described above.
Entering "0" in the first box will disable a report. Entering "0" in the second box will eliminate the expanded message for
that report.
With ADEMCO Contact ID® Reporting: Enter a digit in the first box to enable the zone to report. Use a different
digit for each zone until you have used up available digits. If the number of zones exceeds the number of available
digits, begin with digit 1 again. This is an "enabling" code only and is not the actual code sent to the central station
office. Entries in the second boxes will be ignored. For system status (non-alarm) codes, enter a "1" in the first box for all
the system conditions you want to send to the central station. A "0" in the first box disables the report.
2 = weekly
3 = once every 30 days
4 = 90 days
5 = 180 days
6 = 365 days
✻
56 Enhanced Zone Programming Mode, or codes can be entered in data
–20–
If enabled, provides communication delay to the central station and allows
the subscriber time to avoid a false alarm transmission. Delay does not
apply to zone type 6, 7, 8, and 9 alarms, which are always sent as soon as
they occur. UL installations: must be 0 (no delay)
Test report code entered in field
This is the time to first report from programming or downloading.
Select 0 for all other formats.
If enabled, notifies the central station if an end user is not operating their
security system by sending a System Inactivity report 654. The report will
be sent only to the Primary phone number and only if Contact ID® format
was selected.
Note: The report will follow the
✻
was made in 49.
For Event Logging, Option 2 must be selected.
If the control detects an RF jam condition, a "FAULT" message appears for
zone 90. The Contact ID® code for RF Jam is 344.
Note: This feature cannot be used in conjunction with the 5827 wireless
keypad.
✻
64 is sent.
✻
49 = 0 rules, no matter which selection
✻ ✻ ✻
59 – 76, & 89)