Regulatory Statements - Intermec ScanPlus 1802 Getting Started Manual

Laser warnings (ScanPlus 1802 ST only)
The ScanPlus 1802 ST is a Class 2 laser scanner and complies with the following safety stan dards:
USA: CDRH - Class II Laser Product (CFR 21 Subpart J)
IEC 825-1 EN 60825-1 - Class 2 Laser Product.
These warnings do not apply to the ScanPlus 1802 SR or VT PDF which are CCD scanners and do not contain a laser.
Fix these warning labels onto the product if they
are not already present.
Collez les étiquettes d'aver tis se ment sur votre
pro duit.
Bringen Sie Warnetiketten auf dem Produkt an.
Fije la etiqueta de advertencia en el producto.
Un'etichetta di avviso per il laser è da applicare
sul prodotto.
Cole as etiquetas de precaução no equipamento.
CAUTION – Use of controls or adjustments or performance of procedures other than those specifi ed herein result in
hazardous laser light.
VORSICHT – Bei einer anders als hier beschriebenen Verwendung der Bedienelemente oder Veränderungen oder einer
anderen Ausführung der Arbeitsabläufe entsteht gefährliches Laserlicht.
ATTENTION – L'utilisation de contrôles/commandes ou de réglages ou l'exécution de pro cé du res autres que ceux précisés
par le présent document provoquent une lumière laser dan ge reu se.
12

Regulatory statements

Intermec hereby declares that the ScanPlus 1802 Cordless System has been tested and found compliant with the
below listed stan dards as required by the R&TTE Directive 99/05/EC, EMC Directive 89/336/EEC as amended by
92/31/EEC and by the Low Voltage Di rec ti ve 73/23/EEC as amended by 93/68/EEC: ETS 300 683 (1997 - ScanPlus
1802 SR / ST Cordless System only), EN 301 489 (ScanPlus 1802 VT PDF Cordless System only), EN 300 220-1
(1999), EN 60950 and EN 60825-1. This device is TÜV GS licensed (EN 60950 and EN 60825-1) for safety only when powered
by an external Intermec power supply. The original Declaration of Conformity is available on demand. The ScanPlus 1802
Cordless System is certifi ed for use in all countries belonging to the European Union.
USA & Canada: This device complies with Part 15 of the FCC rules and RSS-210 of Industry Canada. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the
ins truc tions, it may cause harmful interference to radio com mu ni ca tions. However there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference, the user is encouraged to try
to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase
the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit diff erent from
that to which the receiver is connected or consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with the FCC Rules, the I/O cables that interconnect between the device and any peripheral
must be as specifi ed by Intermec.
Caution: Changes or modifi cations not expressly approved by Intermec could void the user's authority to operate this
equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This
device requires a radio license unless it is used totally inside a building (the user must obtain this license).
This device complies with the UL standards (UL1950 / C22.2 n°950).
Cet ap pa reil nu mé ri que de la classe B respecte toutes les exigences du Règlement sur le ma té riel brouilleur du Canada.
Cet appareil exige une license radio à moins d'être entièrement installé dans un batiment (l'utilisateur doit obtenir cette
license).
Cet équipement est conforme aux exigences de CNR-210 de Industrie Canada. L'utilisation de ce dispositif est autorisée aux
conditions suivantes: (1) Il ne doit pas produire de brouillage, et (2) l'utilisateur de l'équipement doit accepter tout brouillage
reçu, même si ce brouillage est susceptible de compromettre son fonctionnement.
Cet équipement est conforme aux normes UL (UL1950 / C22.2 n°950).
Australia-New Zealand: This equipment has been tested and found to conform to the Australian EMC
framework concerning Class B digital devices, prescribed by the Australian and New-Zealand standard
AS/NZS 3548.
The information contained in this document is for informational purposes only and is subject to change without notice.
No part of this document may be copied or reproduced in any manner without the prior written per mis sion of Intermec
Technologies Corporation.
ScanPlus/MicroBar products are covered by patents issued or pending in the USA and other countries.
The word Intermec, the Intermec logo, ScanPlus, MicroBar and EasySet are either trademarks or registered trademarks of
Intermec.
Throughout this document, trademarked names may be used. Rather than put a trademark (™ or ®) symbol in every
occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and to the benefi t of
the trademark owner, with no intention of infringement.
Class 1 LED product - safe when used in any reasonable operating conditions (ScanPlus 1802 SR and VT PDF only).
N309
13