Regulatory Statements - Intermec ScanPlus 1802 Getting Started Manual

Regulatory statements

Intermec hereby declares that the ScanPlus 1802 Cordless System has been tested and found compliant with the
below listed standards as required by the R&TTE Directive 99/05/EC, EMC Directive 89/336/EEC as amended by
92/31/EEC and by the Low Voltage Directive 73/23/EEC as amended by 93/68/EEC: ETS 300 683, EN 301 489, EN
300 220-1 (1999), EN 60950 and EN 60825-1. This device is TÜV GS licensed (EN 60950 and EN 60825-1) for safety
only when powered by an external Intermec power supply. The original Declaration of Conformity is available on demand.
The ScanPlus 1802 Cordless System is certified for use in all countries belonging to the European Union.
USA & Canada: This device complies with Part 15 of the FCC rules and RSS-210 of Industry Canada. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications. However there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference, the user is encouraged to try
to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase
the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from
that to which the receiver is connected or consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with the FCC Rules, the I/O cables that interconnect between the device and any peripheral
must be as specified by Intermec.
Caution: Changes or modifications not expressly approved by Intermec could void the user's authority to operate this
equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This
device requires a radio license unless it is used totally inside a building (the user must obtain this license).
This device complies with the UL standards (UL1950 / C22.2 n°950).
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Cet appareil exige une licence radio à moins d'être entièrement installé dans un bâtiment (l'utilisateur doit obtenir cette
licence).
Cet équipement est conforme aux exigences du CNR-210 de Industrie Canada. L'utilisation de ce dispositif est autorisée aux
conditions suivantes: (1) il ne doit pas produire de brouillage, et (2) l'utilisateur de l'équipement doit accepter tout brouillage
reçu, même si ce brouillage est susceptible de compromettre son fonctionnement.
Cet équipement est conforme aux normes UL (UL1950 / C22.2 n°950).
Australia-New Zealand: This equipment has been tested and found to conform to the Australian
EMC framework concerning Class B digital devices, prescribed by the Australian and New-Zealand
standard AS/NZS 3548.
The information contained in this document is for informational purposes only and is subject to change without notice.
No part of this document may be copied or reproduced in any manner without the prior written permission of Intermec
Technologies Corporation.
ScanPlus/MicroBar products are covered by patents issued or pending in the USA and other countries.
The word Intermec, the Intermec logo, ScanPlus, MicroBar are either trademarks or registered trademarks of Intermec
Technologies Corporation.
EsaySet® is a registered trademark of Intermec Technologies Corporation.
Throughout this document, trademarked names may be used. Rather than put a trademark (™ or ®) symbol in every
occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and to the benefit of
the trademark owner, with no intention of infringement.
Class 1 LED product - safe when used in any reasonable operating conditions.
12
N309