Related Manuals for Wohler RMQ-230-3G
Summary of Contents for Wohler RMQ-230-3G
- Page 1 RMQ-230 Series • RMQ-230-3G • RMQ-230-HD • RMQ-230-SD • RMQ-230-A Quad-Split, LCD, Multi-Viewer Audio/ Video Monitors User Guide Part Number 821081, Revision C...
-
Page 2: Customer Support
Wohler Technologies, Inc. reserves the right to change or improve our products at any time and without notice. In no event will Wohler Technologies, Inc. be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect in the hardware, software, or its documentation, even if advised of the possibility of such damages. -
Page 3: Table Of Contents
RMQ-230 Series Introduction Overview The RMQ-230 Series quad split, LCD video monitors are high- performance 23" professional LCD monitors that support advanced 10-bit digital processing technology and also 3D comb filter and de-interlace, accurate scaling engine, GAMMA correction and color temperature adjustment to achieve the best possible image display. -
Page 4: Safety
R M Q - 2 3 0 S e r i e s S a f e t y Safety Important Safety Instructions Read, keep, and follow all of these instructions; heed all warnings. Do not use this equipment near water, rain or moisture. Use only a dry cloth to clean the equipment. -
Page 5: Installation Recommendations
RMQ-230 Series I n s ta l la t i o n R e c o m me n d a t io n s Safety Symbols WARNING: The symbol to the left warns of electric shock hazard inside the unit. Disconnect the power cord before removing access panels when installing upgrades. -
Page 6: Unpacking And Installation
R M Q - 2 3 0 S e r i e s U n p a c k i n g a n d I n s t a l l a t i o n Note: HDMI 1.3 or 1.4 cable lengths of 2m (6 feet) are guaranteed to work well. - Page 7 RMQ-230 Series U n p a c k i n g a n d I n s t a l l a t i o n • Base board with screws • Adapter (19V) • Power cord • User guide CDROM •...
-
Page 8: Features
R M Q - 2 3 0 S e r i e s F e a t u r e s Install the base to the monitor. Place the monitor on a solid static-free surface. Connect the power cord to the rear panel of the monitor and to mains power. -
Page 9: Front Panel Features
RMQ-230 Series F r o n t P a n e l F e a t u r e s Front Panel Features The following feature descriptions refer to Figure 1–2 below. Figure 1–2 RMQ-230 Front Panel Tally Light Level Meters In-Monitor Display (IMD) Timecode... - Page 10 R M Q - 2 3 0 S e r i e s F r o n t P a n e l F e a t u r e s • Timecode: The display format for the timecode is HH: MM: SS: FF. In the event no timecode is available, the monitor will display --:--:--:--.
- Page 11 RMQ-230 Series F r o n t P a n e l F e a t u r e s • F1/Up and F2/Down: After pressing the MENU button, press to move within submenus. When not in mode, Down MENU are programmable hot keys.
-
Page 12: Rear Panel Features
R M Q - 2 3 0 S e r i e s R e a r P a n e l F e a t u r e s Figure 1–4 RMQ-230 Waveform/Vector Display Vector or Waveform Displays Rear Panel Features The descriptions of the rear panel connectors refer to Figure 1–5 below... - Page 13 RMQ-230 Series R e a r P a n e l F e a t u r e s Figure 1–6 RMQ-230 Rear Panel - Left • DC IN (jack): Accepts included power plug from an adapter. • Power (Rocker Switch): Toggles power to the monitor on or off. •...
- Page 14 R M Q - 2 3 0 S e r i e s R e a r P a n e l F e a t u r e s • Tally (DB-9-F): Controls the LED tally lights. • Audio Inputs (8 RCA) and Outputs (2 RCA): Each input pair...
-
Page 15: Using The Osd Menu
RMQ-230 Series U s i n g t h e O S D M e n u Using the OSD Menu Configuring the RMQ-230 Series monitors is accomplished in the MENU . Each of the menus in the OSD MENU is explained below. -
Page 16: Status Menu
R M Q - 2 3 0 S e r i e s U s in g t h e O SD M e n u Status Menu Note that none of the options displayed on the STATUS menu are editable. -
Page 17: Marker Menu
RMQ-230 Series U s i n g t h e O S D M e n u Table 1–3 Color Temp Menu (Continued) Default Parameters Domain Range Value RED BIAS Factory GREEN BIAS Calibrated BLUE BIAS Resets gain and bias to their factory defaults. RESET Marker Menu Important:... - Page 18 R M Q - 2 3 0 S e r i e s U s in g t h e O SD M e n u Table 1–4 Marker Menu (Continued) Default Parameters Domain Range Value Setting the picture safe area size marker for the aspect ratio (determined by the button to which the aspect function is assigned) and...
- Page 19 RMQ-230 Series U s i n g t h e O S D M e n u Audio Config Menu The menu sets up the audio sources for each channel according to the last button pressed. Speakers and the analog Audio CH 1 CH 4 Output follow...
-
Page 20: User Config Menu
R M Q - 2 3 0 S e r i e s U s in g t h e O SD M e n u Table 1–5 Audio Config Menu (Continued) Default Parameters Domain Range Value Control the audio level meter with the audio source: ACTIVE ONLY (enabled) or... - Page 21 RMQ-230 Series U s i n g t h e O S D M e n u Table 1–6 User Config Menu (Continued) Default Parameters Domain Range Value Select the function to assign to the function button: • MARKER Marker F1 BUTTON •...
-
Page 22: Osd Display
R M Q - 2 3 0 S e r i e s U s in g t h e O SD M e n u OSD Config Menu OSD CONFIG menu has two pages: The IMD DISPLAY and the PROTOCOL. - Page 23 RMQ-230 Series U s i n g t h e O S D M e n u Table 1–7 OSD Config Menu - IMD Display Default Parameters Domain Range Value Select to display the video information: • FORMAT DISPLAY • AUTO •...
- Page 24 R M Q - 2 3 0 S e r i e s U s in g t h e O SD M e n u IMD Display Table 1–8 OSD Config Menu - IMD Protocol Default Parameters Domain Range Value Select the IMD protocol you want to use:...
- Page 25 RMQ-230 Series U s i n g t h e O S D M e n u Table 1–8 OSD Config Menu - IMD Protocol Default Parameters Domain Range Value Select the IMD tally mode: • • • T1T2 IMD TLY MODE •...
-
Page 26: Specifications
R M Q - 2 3 0 S e r i e s S p e c if i c a ti o n s Specifications The general specifications of the RMQ-230 Series monitors are listed in Table 1–9 below. Table 1–9 RMQ-230 Specifications Specification... - Page 27 RMQ-230 Series S p e ci f i c a t i o n s Table 1–11 below distinguishes each of the RMQ-230 models. Table 1–11 RMQ-230 Distinctions Among Each Model Category Specification 1080p: (60/59.94/50) 1080i: (60/59.94/50) 720p: (60/59.94/50) 1035i: (60/59.94) 3G-SDI ...
-
Page 28: Technical Function Overview
R M Q - 2 3 0 S e r i e s T e c h n i c a l F u n c t i o n O v e r v i e w Table 1–13 below lists the specifications for SDI inputs. -
Page 29: Video Source
RMQ-230 Series T e ch n ic a l F u n ct i o n O v e r vi e w Figure 1–9 RMQ-230 Block Diagram RS-485 LED Tally Tally (OSD/UMD) Interface RS-485 Ext Audio Source Audio In 1 Select Audio In 2 Audio In 3...
Need help?
Do you have a question about the RMQ-230-3G and is the answer not in the manual?
Questions and answers